Hallo,
hier kommt also die apcupsd.conf.
Das Programm kann mit der USV nicht richtig kommunizieren,
wenn ich das P. starten will kommt
fatal error in apcserial.c at line 171
panic! can't communicate with ups via serial port
## apcupsd.conf v1.1 ##
#
# for apcupsd release 3.8.2 suse
#
# "apcupsd" POSIX config file
#
# If you have used a prior version of apcupsd, the CONTROL script file
# (/sbin/powersc) has now been replaced by /etc/apcupsd/apccontrol.
# Consequently, the CONTROL configuration statement is obsolete.
# The following configuration statements have been replaced by scripts
# called from /etc/apcupsd/apccontrol, and thus are obsolete:
# BATTCMD, LIMITCMN, LOADCMD, PWRCMD, REBOOTCMD, REMOTECMD, RETCMD,
# and TIMECMD.
#
#
#
# ========= General configuration parameters ============
#
# UPSCABLE [ simple | smart |
# 940-00(20B,23A,24B,24C,24G,95A,95B,95C) |
# 940-15(24C) |
# ether ]
# defines the type of cable that you have.
UPSCABLE smart
#
# UPSTYPE [ backups | sharebasic | netups |
# backupspro | smartvsups |
# newbackupspro | backupspropnp |
# smartups | matrixups | sharesmart ]
# defines the type of UPS you have.
UPSTYPE backupspro
#
#
#DEVICE <string> /dev/<serial port>
# name of your serial port
DEVICE /dev/ttyS0
#
#LOCKFILE <path to lockfile>
# path for serial port lock file
LOCKFILE /var/lock
#
#
#
# ======== configuration parameters used during power failures
==========
#
# Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so
# the first that occurs will cause the initation of a shutdown.
#
# If during a power failure, the remaining battery percentage
# (as reported by the UPS) is below or equal to BATTERYLEVEL,
# apcupsd will initiate a system shutdown.
BATTERYLEVEL 5
#
#
# If during a power failure, the remaining runtime in minutes
# (as calculated internally by the UPS) is below or equal to MINUTES,
# apcupsd, will initiate a system shutdown.
MINUTES 3
#
#
# If during a power failure, the UPS has run on batteries for TIMEOUT
# many seconds or longer, apcupsd will initiate a system shutdown.
# A value of 0 disables this timer.
#
# Note, if you have a Smart UPS, you will most likely want to disable
# this timer by setting it to zero. That way, you UPS will continue
# on batteries until either the % charge remaing drops to or below
BATTERYLEVEL,
# or the remaining battery runtime drops to or below MINUTES. Of
course,
# if you are testing, setting this to 60 causes a quick system
shutdown
# if you pull the power plug.
# If you have an older dumb UPS, you will want to set this to less than
# the time you know you can run on batteries.
TIMEOUT 0
#
#
# Time in seconds between annoying users to signoff prior to
# system shutdown. 0 disables.
ANNOY 300
#
# Initial delay after power failure before warning users to get
# off the system.
ANNOYDELAY 60
#
# The condition which determines when users are prevented from
# logging in during a power failure.
# NOLOGON <string> [ disable | timeout | percent | minutes | always ]
NOLOGON disable
#
#
# If killdelay is set, apcupsd will continue running after a
# shutdown has been requested, and after the specified time in
# seconds attempt to kill the power. This is for use on systems
# where apcupsd cannot regain control after a shutdown.
# KILLDELAY <seconds> 0 disables
KILLDELAY 0
#
#
# ==== Configuration statements the network information server =========
#
# NETSERVER [ on | off ] on enables, off disables the network
# information server. If netstatus is on, a network information
# server process will be started for serving the STATUS and
# EVENT data over the network (used by CGI programs).
NETSERVER on
#
# NISPORT <port> default is 7000
# port to use for sending STATUS and EVENTS data over the network.
# It is not used unless NETSERVER is on. If you change this port,
# you will need to change the corresponding value in the cgi directory
# and rebuild the cgi programs.
NISPORT 7000
#
# If you want the last few EVENTS to be available over the network
# by the network information server, you must define an EVENTSFILE.
# Only the last 50 or so events are kept.
EVENTSFILE /var/log/apcupsd.events
#
#
#
#
# ===== Configuration statements to control apcupsd system logging
========
#
# Time interval in seconds between writing the STATUS file; 0 disables
STATTIME 0
#
# Location of STATUS file (written to only if STATTIME is non-zero)
STATFILE /var/log/apcupsd.status
#
#
# LOGSTATS [ on | off ] on enables, off disables
# Note! This generates a lot of output, so if
# you turn this on, be sure that the
# file defined in syslog.conf for LOG_NOTICE is a named pipe.
# You probably do not want this on.
LOGSTATS off
#
#
# Time interval in seconds between writing the DATA records to
# the log file. 0 disables.
DATATIME 0
#
# FACILITY defines the logging facility (class) for logging to syslog.
# If not specified, it defaults to "daemon". This is useful
# if you want to separate the data logged by apcupsd from other
# programs.
#FACILITY local0
#
#
#
#
# ========== Configuration statements used in updating the UPS EPROM
=========
#
# UPS name, max 8 characters -- used only during -n or --rename-ups
UPSNAME UPS_NAME
#
# Battery date - 8 characters -- used only during -u or
--update-battery-date
#BATTDATE mm/dd/yy
#
# The following items are set during -c or --configure
#
# Sensitivity to line voltage quality (H cause faster transfer to
batteries)
# SENSITIVITY H M L (default = H)
#SENSITIVITY H
#
# UPS delay after power return (seconds)
# WAKEUP 000 060 180 300 (default = 0)
#WAKEUP 60
#
# UPS Grace period after request to power off (seconds)
# SLEEP 020 180 300 600 (default = 20)
#SLEEP 180
#
#
# Low line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 106 103 100 097
# M 177 172 168 182
# A 092 090 088 086
# I 208 204 200 196 (default = 0 => not valid)
#LOTRANSFER 208
#
# High line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 127 130 133 136
# M 229 234 239 224
# A 108 110 112 114
# I 253 257 261 265 (default = 0 => not valid)
#HITRANSFER 253
#
# Battery change needed to restore power
# RETURNCHARGE 00 15 50 90 (default = 15)
#RETURNCHARGE 15
#
# Alarm delay
# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low
battery, N = never
# BEEPSTATE 0 T L N (default = 0)
#BEEPSTATE T
#
# Low battery warning delay in minutes
# LOWBATT 02 05 07 10 (default = 02)
#LOWBATT 2
#
# UPS Output voltage when running on batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 115
# M 208
# A 100
# I 230 240 220 225 (default = 0 => not valid)
#OUTPUTVOLTS 230
#
# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
# SELFTEST 336 168 ON OFF (default = 336)
#SELFTEST 336
#
#
#
# ========== Configuration statements used if sharing =============
# a UPS and controlling it via the network
#
# The configuration statements below are used if you
# want to share one UPS to power multiple machines and have them
# communicate by the network. Obviously, the master is connected
# to the UPS via the serial cable, and it communicates to the
# "slaves" via the network -- i.e. the slaves get their info
# concerning the UPS via the ethernet.
#
# UPSCLASS [ standalone | shareslave | sharemaster | netslave |
netmaster ]
# normally standalone unless you share a UPS with multiple machines.
UPSCLASS standalone
#
# Unless you want to share the UPS (power multiple machines).
# this should be disable
# UPSMODE [ disable | share | net | sharenet ]
UPSMODE disable
#
#NETACCESS <string> [ true | false ] Enable Network Access Support
NETACCESS true
#
# NETTIME <int>
#NETTIME 100
#
# NETPORT <int>
#NETPORT 6666
#
# MASTER <string>
MASTER
#
# SLAVE <string>
#SLAVE
#
# USERMAGIC <string>
#USERMAGIC
#