Hallo,
mein Megaraid 9271-8i Controller piepst und zeigt im Storage Manager auch an,
dass ein Alarm aktiv ist. Darüber hinaus aber keinen Fehler. Alle VDs sind in
optimalem Zustand.
Eine Suppor-Anfrage bei Broadcom wird aus welchen Gründen auch immer nicht
abgesendet, obwohl das Webformular an jedem Eintrag einen grünen Haken
schreibt.
Der Controller hat die aktuelleste Firmware.
Angeschlossen sind 6 SAS HDs im RAID 10 mit je einer Hot Spare.
Außerdem 2 SSDsf im Raid 1 als Cache.
Hat jemand eine Idee wie ich den Fehler lokalisieren und beheben kann.
Neustart und Spannungswechslel waren erfolglos.
Oder kennt jemand ein Forum, in dem solchte Themen besprochen werden?
--
Dirk
Nachstehend die Controllerdaten:
Generating detailed summary of the adapter, it may take a while to complete.
Controller = 0
Status = Success
Description = None
Basics :
======
Controller = 0
Model = LSI MegaRAID SAS 9271-8i
Serial Number = SV42432893
Current Controller Date/Time = 02/17/2024, 14:53:51
Current System Date/time = 02/17/2024, 14:53:51
SAS Address = 500605b008f770d0
PCI Address = 00:05:00:00
Mfg Date = 06/12/14
Rework Date = 00/00/00
Revision No = 28A
Version :
=======
Firmware Package Build = 23.34.0-0019
Firmware Version = 3.460.115-6465
Bios Version = 5.50.03.0_4.17.08.00_0x06110200
WebBIOS Version = 6.1-76-e_76-Rel
Preboot CLI Version = 05.07-00:#%00011
NVDATA Version = 2.1507.03-0162
Boot Block Version = 2.05.00.00-0010
Bootloader Version = 07.26.26.219
Driver Name = megaraid_sas
Driver Version = 07.713.01.00-rc1
Bus :
===
Vendor Id = 0x1000
Device Id = 0x5B
SubVendor Id = 0x1000
SubDevice Id = 0x9271
Host Interface = PCI-E
Device Interface = SAS-6G
Bus Number = 5
Device Number = 0
Function Number = 0
Pending Images in Flash :
=======================
Image name = No pending images
Status :
======
Controller Status = Optimal
Memory Correctable Errors = 0
Memory Uncorrectable Errors = 0
ECC Bucket Count = 0
Any Offline VD Cache Preserved = No
BBU Status = 0
Support PD Firmware Download = No
Lock Key Assigned = No
Failed to get lock key on bootup = No
Lock key has not been backed up = No
Bios was not detected during boot = No
Controller must be rebooted to complete security operation = No
A rollback operation is in progress = No
At least one PFK exists in NVRAM = Yes
SSC Policy is WB = Yes
Controller has booted into safe mode = No
Supported Adapter Operations :
============================
Rebuild Rate = Yes
CC Rate = Yes
BGI Rate = Yes
Reconstruct Rate = Yes
Patrol Read Rate = Yes
Alarm Control = Yes
Cluster Support = No
BBU = Yes
Spanning = Yes
Dedicated Hot Spare = Yes
Revertible Hot Spares = Yes
Foreign Config Import = Yes
Self Diagnostic = Yes
Allow Mixed Redundancy on Array = No
Global Hot Spares = Yes
Deny SCSI Passthrough = No
Deny SMP Passthrough = No
Deny STP Passthrough = No
Support more than 8 Phys = Yes
FW and Event Time in GMT = No
Support Enhanced Foreign Import = Yes
Support Enclosure Enumeration = Yes
Support Allowed Operations = Yes
Abort CC on Error = Yes
Support Multipath = Yes
Support Odd & Even Drive count in RAID1E = No
Support Security = No
Support Config Page Model = Yes
Support the OCE without adding drives = Yes
Support EKM = No
Snapshot Enabled = No
Support PFK = Yes
Support PI = Yes
Support LDPI Type1 = No
Support LDPI Type2 = No
Support LDPI Type3 = No
Support Ld BBM Info = No
Support Shield State = Yes
Block SSD Write Disk Cache Change = No
Support Suspend Resume BG ops = Yes
Support Emergency Spares = No
Support Set Link Speed = Yes
Support Boot Time PFK Change = No
Support JBOD = No
Disable Online PFK Change = No
Support Perf Tuning = Yes
Support SSD PatrolRead = Yes
Real Time Scheduler = Yes
Support Reset Now = Yes
Support Emulated Drives = Yes
Headless Mode = Yes
Dedicated HotSpares Limited = No
Point In Time Progress = Yes
Extended LD = Yes
Boot Volume Supported = No
Support Uneven span = No
Support Config Auto Balance = No
Support Maintenance Mode = No
Support Diagnostic results = No
Support Ext Enclosure = Yes
Support Sesmonitoring = No
Support SecurityonJBOD = No
Support ForceFlash = No
Support DisableImmediateIO = No
Support LargeIOSupport = No
Support DrvActivityLEDSetting = Yes
Support FlushWriteVerify = Yes
Support CPLDUpdate = No
Support ForceTo512e = Yes
Support discardCacheDuringLDDelete = No
Support JBOD Write cache = No
Support Large QD Support = No
Support SRIOV Options = No
Supported PD Operations :
=======================
Force Online = Yes
Force Offline = Yes
Force Rebuild = Yes
Deny Force Failed = No
Deny Force Good/Bad = No
Deny Missing Replace = No
Deny Clear = No
Deny Locate = No
Support Power State = Yes
Set Power State For Cfg = No
Support T10 Power State = No
Support Temperature = Yes
NCQ = Yes
Support Max Rate SATA = No
Support Degraded Media = No
Support Parallel FW Update = No
Support Drive Crypto Erase = No
Supported VD Operations :
=======================
Read Policy = Yes
Write Policy = Yes
IO Policy = Yes
Access Policy = Yes
Disk Cache Policy = Yes
Reconstruction = Yes
Deny Locate = No
Deny CC = No
Allow Ctrl Encryption = No
Enable LDBBM = No
Support FastPath = Yes
Performance Metrics = Yes
Power Savings = No
Support Powersave Max With Cache = No
Support Breakmirror = No
Support SSC WriteBack = Yes
Support SSC Association = Yes
Support VD Hide = No
Support VD Cachebypass = No
Support VD discardCacheDuringLDDelete = No
Advanced Software Option :
========================
--------------------------------------------------------------
Adv S/W Opt Time Remaining Mode
--------------------------------------------------------------
MegaRAID FastPath Unlimited Secured
MegaRAID CacheCade Pro 2.0 Unlimited Secured
MegaRAID RAID6 Unlimited Factory Installed
MegaRAID RAID5 Unlimited Factory Installed
Cache Offload Unlimited Factory Installed
--------------------------------------------------------------
Safe ID = 95C8A1TVM2X9UJTEGN74D1VKQVGRCM6AF2HCP6RZ
HwCfg :
=====
ChipRevision = D1
BatteryFRU = N/A
Front End Port Count = 0
Backend Port Count = 8
BBU = Present
Alarm = On
Serial Debugger = Present
NVRAM Size = 32KB
Flash Size = 16MB
On Board Memory Size = 1024MB
CacheVault Flash Size = NA
TPM = Absent
Upgrade Key = Present
On Board Expander = Absent
Temperature Sensor for ROC = Present
Temperature Sensor for Controller = Absent
Upgradable CPLD = Absent
Current Size of CacheCade (GB) = 73
Current Size of FW Cache (MB) = 787
ROC temperature(Degree Celsius) = 76
Policies :
========
Policies Table :
==============
------------------------------------------------
Policy Current Default
------------------------------------------------
Predictive Fail Poll Interval 300 sec
Interrupt Throttle Active Count 16
Interrupt Throttle Completion 50 us
Rebuild Rate 30 % 30%
PR Rate 30 % 30%
BGI Rate 30 % 30%
Check Consistency Rate 30 % 30%
Reconstruction Rate 30 % 30%
Cache Flush Interval 4s
------------------------------------------------
Flush Time(Default) = 4s
Drive Coercion Mode = 1GB
Auto Rebuild = On
Battery Warning = On
ECC Bucket Size = 15
ECC Bucket Leak Rate (hrs) = 24
Restore HotSpare on Insertion = Off
Expose Enclosure Devices = On
Maintain PD Fail History = Off
Reorder Host Requests = On
Auto detect BackPlane = SGPIO/i2c SEP
Load Balance Mode = Auto
Security Key Assigned = Off
Disable Online Controller Reset = Off
Use drive activity for locate = On
Boot :
====
BIOS Enumerate VDs = 1
Stop BIOS on Error = Off
Delay during POST = 0
Spin Down Mode = Internal Only
Enable Ctrl-R = No
Enable Web BIOS = Yes
Enable PreBoot CLI = Yes
Enable BIOS = No
Max Drives to Spinup at One Time = 2
Maximum number of direct attached drives to spin up in 1 min = 10
Delay Among Spinup Groups (sec) = 12
Allow Boot with Preserved Cache = Off
High Availability :
=================
Topology Type = None
Cluster Permitted = No
Cluster Active = No
Defaults :
========
Phy Polarity = 0
Phy PolaritySplit = 0
Strip Size = 64 KB
Write Policy = WB
Read Policy = RA
Cache When BBU Bad = Off
Cached IO = Off
VD PowerSave Policy = Automatic
Default spin down time (mins) = 30
Coercion Mode = 1 GB
ZCR Config = Unknown
Max Chained Enclosures = 16
Direct PD Mapping = No
Restore Hot Spare on Insertion = No
Expose Enclosure Devices = Yes
Maintain PD Fail History = No
Zero Based Enclosure Enumeration = No
Disable Puncturing = No
EnableLDBBM = No
DisableHII = No
Un-Certified Hard Disk Drives = Allow
SMART Mode = Mode 6
Enable LED Header = No
LED Show Drive Activity = No
Dirty LED Shows Drive Activity = No
EnableCrashDump = No
Disable Online Controller Reset = No
Treat Single span R1E as R10 = No
Power Saving option = Enabled
TTY Log In Flash = Yes
Auto Enhanced Import = Yes
BreakMirror RAID Support = No
Disable Join Mirror = No
Enable Shield State = No
Time taken to detect CME = 60 sec
Capabilities :
============
Supported Drives = SAS, SATA
Boot Volume Supported = NO
RAID Level Supported = RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50,
RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported,
PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span
Enable JBOD = No
Mix in Enclosure = Allowed
Mix of SAS/SATA of HDD type in VD = Allowed
Mix of SAS/SATA of SSD type in VD = Allowed
Mix of SSD/HDD in VD = Not Allowed
SAS Disable = No
Max Arms Per VD = 32
Max Spans Per VD = 8
Max Arrays = 128
Max VD per array = 64
Max Number of VDs = 64
Max Parallel Commands = 1008
Max SGE Count = 60
Max Data Transfer Size = 8192 sectors
Max Strips PerIO = 42
Max Configurable CacheCade Size(GB) = 512
Max Transportable DGs = 0
Min Strip Size = 8 KB
Max Strip Size = 1.0 MB
Scheduled Tasks :
===============
Consistency Check Reoccurrence = 168 hrs
Next Consistency check launch = 02/20/2024, 21:00:00
Patrol Read Reoccurrence = 168 hrs
Next Patrol Read launch = 02/22/2024, 00:00:00
Battery learn Reoccurrence = 670 hrs
Next Battery Learn = 03/09/2024, 02:00:00
OEMID = LSI
Drive Groups = 2
TOPOLOGY :
========
------------------------------------------------------------------------------
DG Arr Row EID:Slot DID Type State BT Size PDC PI SED DS3 FSpace TR
------------------------------------------------------------------------------
0 - - - - RAID10 Optl N 14.553 TB dsbl N N none N N
0 0 - - - RAID1 Optl N 7.276 TB dsbl N N none N N
0 0 0 252:0 34 DRIVE Onln N 7.276 TB dsbl N N none - N
0 0 1 252:4 38 DRIVE Onln N 7.276 TB dsbl N N none - N
0 1 - - - RAID1 Optl N 7.276 TB dsbl N N none N N
0 1 0 252:1 33 DRIVE Onln N 7.276 TB dsbl N N none - N
0 1 1 252:5 35 DRIVE Onln N 7.276 TB dsbl N N none - N
0 - - 252:2 36 DRIVE DHS - 7.276 TB - - - - - N
1 - - - - Cac1 Optl N 73.574 GB dflt N N none N N
1 0 - - - RAID1 Optl N 73.574 GB dflt N N none N N
1 0 0 252:3 32 DRIVE Onln N 73.574 GB dflt N N none - N
1 0 1 252:7 27 DRIVE Onln N 222.585 GB dflt N N none - N
------------------------------------------------------------------------------
DG=Disk Group Index|Arr=Array Index|Row=Row Index|EID=Enclosure Device ID
DID=Device ID|Type=Drive Type|Onln=Online|Rbld=Rebuild|Dgrd=Degraded
Pdgd=Partially degraded|Offln=Offline|BT=Background Task Active
PDC=PD Cache|PI=Protection Info|SED=Self Encrypting Drive|Frgn=Foreign
DS3=Dimmer Switch 3|dflt=Default|Msng=Missing|FSpace=Free Space Present
TR=Transport Ready
Virtual Drives = 2
VD LIST :
=======
----------------------------------------------------------------
DG/VD TYPE State Access Consist Cache Cac sCC Size Name
----------------------------------------------------------------
0/0 RAID10 Optl RW Yes NRAWBD RW ON 14.553 TB
1/1 Cac1 Optl RW Yes NRWBD - ON 73.574 GB
----------------------------------------------------------------
Cac=CacheCade|Rec=Recovery|OfLn=OffLine|Pdgd=Partially Degraded|Dgrd=Degraded
Optl=Optimal|RO=Read Only|RW=Read Write|HD=Hidden|TRANS=TransportReady|
B=Blocked|
Consist=Consistent|R=Read Ahead Always|NR=No Read Ahead|WB=WriteBack|
AWB=Always WriteBack|WT=WriteThrough|C=Cached IO|D=Direct IO|sCC=Scheduled
Check Consistency
Physical Drives = 8
PD LIST :
=======
---------------------------------------------------------------------------------
EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp
Type
---------------------------------------------------------------------------------
252:0 34 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:1 33 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:2 36 DHS 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:3 32 Onln 1 73.574 GB SATA SSD N N 512B INTEL SSDSC2BB080G6 U -
252:4 38 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:5 35 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:6 37 DHS 7.276 TB SAS HDD N N 512B HUH728080AL5200 U -
252:7 27 Onln 1 222.585 GB SATA SSD N N 512B INTEL SSDSC2KB240G8 U -
---------------------------------------------------------------------------------
EID-Enclosure Device ID|Slt-Slot No.|DID-Device ID|DG-DriveGroup
DHS-Dedicated Hot Spare|UGood-Unconfigured Good|GHS-Global Hotspare
UBad-Unconfigured Bad|Onln-Online|Offln-Offline|Intf-Interface
Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info
SeSz-Sector Size|Sp-Spun|U-Up|D-Down|T-Transition|F-Foreign
UGUnsp-Unsupported|UGShld-UnConfigured shielded|HSPShld-Hotspare shielded
CFShld-Configured shielded|Cpybck-CopyBack|CBShld-Copyback Shielded
Cachevault_Info :
===============
---------------------------------------------------------
Model State Temp Mode MfgDate Next Learn
---------------------------------------------------------
CVPM02 Optimal 38C - 2015/03/27 2024/03/09 02:15:55
---------------------------------------------------------
seqNum: 0x00012ac3
Time: Mon Nov 7 02:49:58 2022
Code: 0x000000fb
Class: 2
Locale: 0x01
Event Description: VD 00/0 is now DEGRADED
Event Data:
===========
Target Id: 0
seqNum: 0x00012ace
Time: Mon Nov 7 02:51:02 2022
Code: 0x00000159
Class: 2
Locale: 0x20
Event Description: Controller encountered a fatal error and was reset
Event Data:
===========
None
seqNum: 0x000151ee
Time: Sat Jul 1 08:37:17 2023
Code: 0x000000fb
Class: 2
Locale: 0x01
Event Description: VD 01/1 is now DEGRADED
Event Data:
===========
Target Id: 1
seqNum: 0x00015420
Seconds since last reboot: 83
Code: 0x000000fb
Class: 2
Locale: 0x01
Event Description: VD 01/1 is now DEGRADED
Event Data:
===========
Target Id: 1
Controller = 0
Status = Success
Description = None
Events = GETEVENTS
Controller Properties :
=====================
------------------------------------
Ctrl Status Method Value
------------------------------------
0 Success handleSuboption Events
