Hallo Zusammen,
ich habe in meinen Rechner eine "CC HFC 2BDS0" eingebaut und hatte
versucht mittels Capisuite das Faxen zu regeln, bei Start kommt dieser
Fehler "Can't start Capi abstraction". Funktioniert diese Konstellation
nicht? Leider ist bei der Auswahl in YaST nur HISAX und nicht Capi
auswählbar, liegt es daran?
Vielen Dank für jeden Tip und Gruß
Daniel
Hallo Karsten,
Hallo Liste,
Wiedermal ein Problem mit der AVM C2...
Beim Entladen des Treibers (sei es rcisdn restart oder ein init 6) schmiert
der Rechner bei
Unloading ISDN driver . capi c4_
ab.
SuSE Online Update, oder wie im letzten Beispiel ein frisch kompilierter
Kernel haben beide den gleichen Effekt.
KRW1:~ # uname -a
Linux KRW1 2.6.14.3 #1 SMP Tue Nov 29 17:00:41 CET 2005 i686 i686 i386
GNU/Linux
KRW1:~ # lsmod | grep isdn
isdn 136640 9 capidrv
Slhc 8064 1 isdn
KRW1:~ # lsmod | grep capi
capidrv 30644 2
isdn 136640 9 capidrv
capi 19520 0
capifs 6792 2 capi
kernelcapi 48128 4 c4,b1,capidrv,cap
KRW1:~ # lsmod | grep c4
C4 20868 2
B1 25216 1 c4
kernelcapi 48128 4 c4,b1,capidrv,cap
Das komplette ISDN subsystem ist im aktuellen Kernel als Modul kompiliert.
Jede Hilfe ist willkommen - wenn mehr Infos gebraucht werden, bitte Bescheid
geben.
Mit freundlichen Grüßen,
--
Christian Krbusek
Maintenance
FREQUENTIS GmbH
Postal Address:
A-1120 Wien, Spittelbreitengasse 34
Office Address:
A-1120 Wien, Wolfganggasse 58-60 christian.krbusek(a)frequentis.com
Tel. +43/1/81150-1570
Fax. +43/1/8115077-1570
Hallo,
ich will jetzt mal meinen SMS-Versand umstellen. Bisher nutzte ich auf
einem (uralten) Server ein analoges Modem und sms-client. Unter SuSE 6.2 :-)
Nun möchte ich gerne den SMS-Versand von meinem Fax-Server machen
lassen. Darauf läuft SuSE 7.1 mit hylafax als Faxsoftware und AVMs
CAPI-Treibern. ISDN-Hardware ist eine FritzCard PCI. (Ja, der Rechner
ist nicht der schnellste, nein, er ist nicht per Internet erreichbar und
es gibt auch keine Benutzeraccounts darauf, und wenn sich jemand einlogt
werde ich informiert etc. :-)
Nachdem ich etwas gegoogelt habe (die manual-Seiten zu hylafax sind da
nicht sehr hilfreich) stellte ich fest, dass SNPP-zu-SMS wohl möglich
sein müsste, aber gelinde gesagt schwach dokumentiert ist. Oder es ist
schon zu spät...
Yaps sollte im Prinzip funktionieren, aber auch da schien mir die
Dokumentation etwas dünn.
Dann gibt es noch sms-client, aber auch da scheint die Entwicklung
entweder abgeschlossen zu sein oder wenig detaillierte Dokumentation
erzeugt zu haben.
Weitere Erkenntnisse brachten weder die Listenarchive noch allgemeines
googeln.
Für mich stellt sich jetzt die Frage, welche Lösung ich bevorzugen
möchte. Normalerweise würde ich einfach mal mit sms-client anfangen zu
probieren, aber angesichts meiner mageren Suchergebnisse würde es mich
mal interessieren ob jemand anders eine SMS-Versandlösung über CAPI/ISDN
einsetzt. Oder ob es noch bessere Möglichkeien gibt als was ich
geschildert habe.
Ach so, ich möchte nur SMS versenden, nur über ISDN (nicht per
GSM-Modem), und würde aus praktischen Gründen gerne eine Lösung mit
integrierter Sendequeue benutzen.
Danke für Feedback,
Arno
--
IT-Service Lehmann al(a)its-lehmann.de
Arno Lehmann http://www.its-lehmann.de
Hallo
Mein (linux-) rechner ist in ein Netz eingebunden und hat auch eine
default-route auf der Netzwerkkarte.
Wenn sich der rechner per ipppd mit dem Internet verbindet soll die
default route auf die des providers gesetzt werden. Mittels
'defaultroute' und 'deldefaultroute' als ipppd optionen klappt das auch
ganz gut.
Nach Beendigung der ppp-verbindung ist dann die defaultroute zum
provider weg, leider auch die vorher gesetzte default route auf der
netzwerkkarte.
Hat da jemand einen Lösungsvorschlag wie ich die "alte" default route
automatisch wiederherstellen kann (option ipppd)?
Thomas
Hallo,
mein Hylafax setzt kalsche permissions beim ablegen von eintreffenden
faxe (und bei den Logfiles):
-rw-rw---- 1 fax dialout 33943 2005-11-27 13:44 fax00006.tif
Und das obwohl als FileMode bei beiden rw-rw-rw- eingetragen ist:
thomas@server:/var/spool/fax > grep 666 etc/* 2>/dev/null
etc/config.faxCAPI:LogFileMode: 0666
etc/config.faxCAPI:RecvFileMode: 0666
Hält sich c2faxrecv eventuell nicht daran?
Wenn ja wo muss ich das einstellen?
Thomas
Hallo,
nachdem ich nun jezt meine AVM B1 zum Laufen bekommen habe (sehr
undurchsichtig das gestrüpp aus capi, capi4hylafax, hylafax, suse), ist
mir beim testen aufgefallen daß c2faxrecv anscheinend nur mit 9600 baud
empfängt:
Incoming analog call on controller 1 to 709582.
Connection established.
BaudRate = 9600
Flags = HighRes, MMR_compr
Write fax in path /var/spool/fax to file recvq/fax00004.tif.
Gestartet wird c2faxrecv in der inittab mit
fr:2345:once:/usr/local/bin/c2faxrecv -q "/var/spool/fax"
Kann die Karte wirklich nur mit 9600baud empfangen?
Thomas
Hallo,
gibt es schon eine Lösung ich hab gerade meinen Server auf AMD 64 Bit
umgestellt. Ich bekomme aber nur 8 Byte lange tif's (Faxe). Ich hab auch
schon von AVM den neuen 64 Bit fcpci-suse93-64bit-3.11-07.tar.gz drauf.
Ich will nicht auf wieder auf 32 Bit umstellen, der Rest läuft so schön.
--
------------------------------------------------------------------------
Ing. Gerhard Scheutz
GROSSPOINTNER GmbH & Co.KG
IT Lösungen
t: +43 6135 20820
Sarstein 17 e: scheutz(a)grosspointner.at
4822 Bad Goisern i: www.grosspointner.at
------------------------------------------------------------------------
Hallo Leute,
SuSE 10.0, AMD Athlon, Fitzcad DSL (DSL+ISDN)
wobei wir hier bis heute nur ISDN haben :-((
Diese Fritzcard raubt mir den letzten Nerv.
Zuerst regelmäßig Protocol error layer 2, dann nach Umstecken in einen anderen
PCI-Slot nur noch unregelmäßig (immerhin eine Verbesserung)
aber dafür regelmäßig:
capidrv-1: DISCONNECT_IND reason 0x3301 (Protocol error layer 1 (broken line
or B-channel removed by signalling protocol)) for plci 0x901
wobei die Einwahl manchmal gar nicht stattfindet (ohne Grund)
sowas hatte ich mit meiner alten Teles nicht, (meine Leitung ist in Ordnung).
Muss ich den Treiber von Fritz nehmen, oder geht da auch was anderes.
Yast bietet ja keine andere Möglichkeit oder?
Fax und so brauche ich nicht.
Grüße GG
Am Mo 21.11.2005 19:31 schrieb Volker Grabbe <Volker(a)grabbe.info>:
> Am Sonntag, 20. November 2005 08:46 schrieb Christian Lange:
> > Am So 20.11.2005 00:31 schrieb Arno Lehmann <al(a)its-lehmann.de>:
> > > Hallo,
> > >
> > > Karsten, Christian - Danke. Werde also erstmal mit yaps anfangen
> > > und
> > > sehen ob mir das zusagt. Ein kleiner wrapper für eine
> > > minimalistische
> > > queue sollte als shellscript gehen können...
> > >
> > > Arno
> >
> > Am schwierigsten war es, die passenden Provider Einstellungen zu
> > finden.
>
> Kanst du mir da helfen? ich wollte genau wi e mit Tobit David SMS
> direkt
> versenden und bin auf diesen Thread gestoßen. Was für einstellungen
> muss ich
> in der yaps.rc machen damit ich SMS für T-Mobile, Vodafone E-plus und
> O2
> versenden kann?
>
> Danke
>
> --
>
> Mit freundlichen Grüßen
>
>
> Volker Grabbe
>
> P.S. Diese Email enthält eine digitale Signatur nach dem GnuPG
> Standard.
> Informationen darüber finden Sie beim
> Bundesministerium zur Sicherheit in der Informationstechnik.
Hallo Volker,
ich habe nur D2 verwendet; eine entsprechende yaps.rc folgt. Ob die
Rufnummer für D2 noch funktioniert, weiss ich nicht, da ich yaps
(ersatzlos) seit ca. 0.5 Jahren nicht mehr verwende (musste daher auch
erst das entsprechende Band raussuchen ...).
Gruß,
Christian
******************** yaps.rc ***********************************
#-----------------------------------------------------------------------
# global section
#-----------------------------------------------------------------------
# This is a comma seperated list of available services. This
# is required for autodetect the matching service for a
# pager-id
services D2,D2-3,D2-4
#services D1,D1-0,D1-5,D2,D2-3,D2-4,E+,Eplus8,VIAG,VIAG-6
#+services Telmi,Telmi-Fun,Telmi-Family,Telmi-Top,Telmi-Pro
#+services Skyper,Quix
# This is the default caller-id. If the protocol/service allowes
# it, this is inserted in the message (and the receiver gets this
# as the sender's number)
call-id +49-(511)-4xxxxxx
# If you forget to sign your message, you can automatically append
# this string to each message.
signature (MEIN SMS ALARM)
# You can either switch the use of the signature here on for all
# services or in each service section for that particular service.
use-signature True
# To get more verbose output when running yaps increase this value.
# Currently 4 is the highest supported value.
verbose 1
# If you'd like to log every sending session define this. It should
# point to a writeable file. If you install the software setgid, then
# change the group of this file to the same yaps uses and make it
# group writeable.
logfile /var/log/yaps.log
# A comma seperated list of modem sections. You can also define this
# in each service section.
modems standard
# some global defaults for the serial interface (even if the most
# protocols are assuming 7e1, these settings seem to work well)
speed 38400
bits-per-byte 8
parity none
stopbits 1
# To calculate the cost for each call, you can define some globales
# here and do the fine tuning in each protocol
cost cost=0.12,unit=EU,remainder=2,dial-overhead=13
# These are two example of internal conversion tables. The can be
# used using the `convert' entry (see below).
# cv-default
cv-default {
Ä [
Ö \
Ü ]
ä {
ö |
ü }
ß ~
}
cv-extend {
\l \s
\n \s
\r \s
\f \s
\t \s
}
}
#-----------------------------------------------------------------------
# These values are normally only found in each service section,
# but are listen here with an explaination for completeness.
#-----------------------------------------------------------------------
# This is the phone number of the modem gateway for this service
#phone 0015559876
# This is the protocol the service uses. Currently this can be
# either ascii, script, ucp or tap. Each protocol has a set of
# special configuration parameters, see below.
#protocol tap
# Most services limit the length of a message to a specific length.
# Enter the value here to check valid messages
#max-size 160
# If a message is longer than max-size, you can set this to split
# it off into several single messages of allowed length
#may-split True
# If a message is longer than max-size, you can set this to truncate
# the message to the allowed length. The remaining part is discarded.
#truncate True
# Some services allow to send more than one message per session. If
# it is limited, set it using this parameter
#max-messages 1
# If the service allows using your caller-id set this to True.
#use-call-id True
# If the service is reachable over a phonenumber where the pager-id
# is part of the phone number, define this and add a `%P' anywehere
# in the `phone' number.
#insert-pager-id True
# Remove these characters from the pager-id, as they are not valid
rm-invalids-pid + (-)
# Dito for caller id
rm-invalids-cid + (-)
# Check for valid call id (see below for more details) While
# valid-pid is required, this is optional
#valid-cid ^(001|1)
#change-cid 001
# Depending on your system the value for this parameter is either a
# regular expression or a simple list of strings (seperated by bars)
# which must match the prefix of the pager-id.
#valid-pid ^(0171|0049171)
#valid-pid 0171|0049171
# Use these paramters in the global section if you want do not want
# to check pager-ids (and do not set change-pid):
#valid-pid .
#valid-pid -
# If a pagerid has matched the expression above, then the matching part
# may be replaced by this string
#change-pid 0171
# As the services do not use (in general) the ISO 8859/1 character set,
# one can define convertion tables. you can either specify a file which
# contains the convertion rules:
#conv-table /usr/local/lib/yaps/iso2din.tab
# or use predefined convertion rules
#convert *no-control,*no-8bit,cv-default,cv-extended
# If this is set, send a message even if a requested feature is
# not available
#force True
# If the provider supportes to set a delay for sending the message,
# set this
#can-delay True
# If the provider can delete a buffered message after a period of time,
# set this
#can-expire True
# If the provider can report a delivery status, set this.
#can-rds True
# To check wether a call-id/pager-id is valid use these paramters.
# For the exact syntax see the documentation
#check-call-id >1111111111111111<
#check-pager-id >1111111111111111<
#check-call-id +minimum=0,maximum=16,type=numeric
#-----------------------------------------------------------------------
# These values are typically found in a modem section, but can also
# appear in the global section to set some defaults
#-----------------------------------------------------------------------
# Set this to the modem device you wish to use
#device /dev/modem
#device /dev/cua1
#device /dev/cua/a
# Set this to the prefix of the lockfile use for the device. There
# are several places, and two common formats:
#lock-prefix /usr/spool/uucp/LCK..
#lock-prefix /var/spool/lock/LCK..
lock-prefix /var/spool/locks/LK.
# The different format of the part which is appended to the lockfile
# and the contents can be specified here. See documentation for a
# full list inclusive explaination
#lock-method sysv4
#lock-method binary
#lock-method timeout=10
# These are send/expect sequences to talk to the modem. For an exact
# definition see (again) the documentation. Following entries are
# supported:
# init: to initialize the modem
# local-init: a second initialization string, used to customize
# already defined modems for different handling
# dial: to dial a phone number %L is replaced with the
# phone number itself
# timeout: the default timeout in seconds to wait for answers
# reset: to reset the modem
#-----------------------------------------------------------------------
# service section
#-----------------------------------------------------------------------
#-----------------------------------------------------------------------
# Vodafone - D2
#-----------------------------------------------------------------------
[D2]
modem standard-d2
protocol ucp
valid-pid 0172|0049172|49172
change-pid 0172
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
#phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
[D2-3]
modem standard-d2
protocol ucp
valid-pid 0173|0049173|49173
change-pid 0173
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
#phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
[D2-4]
modem standard-d2
protocol ucp
valid-pid 0174|0049174|49174
change-pid 0174
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
#phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
#-----------------------------------------------------------------------
# modem section
#-----------------------------------------------------------------------
[standard]
# Locking
#
# Older Unix versions
#lock-prefix /usr/spool/uucp/LCK..
# Newer Unix versions
#lock-prefix /var/spool/uucp/LCK..
#lock-prefix /var/lock/LCK..
# SysV4
lock-prefix /var/spool/locks/LK.
#lock-method sysv4
# lock-prefix /var/lock/LCK..
# Device
#
# Typical a symbolic link to the real device
#device /dev/modem
# "normal" call-out device
#device /dev/cua1
# Solaris convention
#device /dev/cua/a
# use the following device for isdn-dialout:
device /dev/ttyI0
# Modem talk
#
#init \\r !200D ATZ\r <OK ATE0Q0V1\r <OK
# use the following init-string for isdn:
# and change MSN to your MSN (what else...:-))
init \\r !200D ATZ\r <OK AT&E47339954\r <OK
dial ATD%L\r <60CONNECT|OK|BUSY|NO\sDIALTONE|NO\sCARRIER
reset ATZ\r <OK
timeout 10
# Customizing an existing modem entry
[standard-d2] standard
local-init AT\%C2\r <OK
#-----------------------------------------------------------------------
# alias section
#-----------------------------------------------------------------------
[alias]
christian 0172xxxxxxx
Hallo,
ich bin mir nicht 100% sicher, ob ich im richtigen Forum bin. Ich stelle
aber trotzdem mal meine Frage:
Ich waehle mich mit meinem Suse Linux 9.0 Rechner ins Internet ein.
Danach moechte ich auch mit meinem Windows Client, der ueber ein 192er
Netz an den Linux Rechner verbunden ist auch ins Internet kommen. Dazu
muss man offensichtlich ein Routing aufsetzen, Dinge an der Firewall
beachten etc. Zu beruecksichtigen ist, dass mein ISDN Zugang ueber eine
Hagenuk Databox, die an der seriellen Schnittstelle ein AT-Modem
simuliert, reaslisiert ist.
Hat vielleicht jemand eine Referenz auf eine vollstaendige Anleitung
bzgl. dieses Themas die alle Aspekte beruecksichtigt um die Sache in
Gang zu bringen? Ich habe mich schon am Routing versucht, hatte aber
bisher leider keinen Erfolg damit.
Danke und Gruss,
Roland