September 2012 - openSUSE Users - openSUSE Mailing Lists

[opensuse] Dual monitor config (12.2 GeForce GT520)
by Dylan 04 Oct '12

04 Oct '12

I am trying to set up dual monitors on my newly installed 12.2. I have a GeForce GT520, using the nvidia driver (x11-video-nvidiaG02 304.43-2.0.1 from obs://build.suse.de/home:sndirsch:drivers) The monitors are attached to VGA-0 and HDMI-0 (output of xrandr below) The monitor on VGA-0 displays correctly, but with the screen on HDMI-0 the desktop extends beyond the top and bottom of the physical screen. Previously, this screen was running correctly at the same resolution (but as a solo monitor on a different graphics card.) I think the problem would be related to the fact that in the previous set up, that screen was running at 60Hz, whereas now it gets automatically set to 50Hz. Any assistance would be gratefully accepted ... Dylan dylan@zen:~> xrandr --current --verbose Screen 0: minimum 8 x 8, current 2560 x 1024, maximum 16384 x 16384 <SNIP> VGA-0 connected 1280x1024+1280+0 (0x27d) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x27c Timestamp: 56641 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 1 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff004c2d5a0037314847 1e0c01030f221b8cea6f86a25a4d9424 1a4f54bfef8081806140454031400101 010101010101302a009851002a403070 1300520e1100001e000000fd0038551e 510d000a202020202020000000fc0053 796e634d61737465720a2020000000ff 0048344c543730363031350a20200025 SignalFormat: VGA supported: VGA ConnectorType: VGA ConnectorNumber: 2 (0x00000002) _ConnectorLocation: 2 (0x00000002) 1280x1024 (0x27d) 108.0MHz +HSync +VSync *current +preferred h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 64.0KHz v: height 1024 start 1025 end 1028 total 1066 clock 60.0Hz 1280x1024 (0x27e) 135.0MHz +HSync +VSync h: width 1280 start 1296 end 1440 total 1688 skew 0 clock 80.0KHz v: height 1024 start 1025 end 1028 total 1066 clock 75.0Hz 1024x768 (0x27f) 78.8MHz +HSync +VSync h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz v: height 768 start 769 end 772 total 800 clock 75.0Hz 1024x768 (0x280) 75.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz v: height 768 start 771 end 777 total 806 clock 70.1Hz 1024x768 (0x281) 65.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 800x600 (0x282) 49.5MHz +HSync +VSync h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz v: height 600 start 601 end 604 total 625 clock 75.0Hz 800x600 (0x283) 50.0MHz +HSync +VSync h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz v: height 600 start 637 end 643 total 666 clock 72.2Hz 800x600 (0x284) 40.0MHz +HSync +VSync h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz v: height 600 start 601 end 605 total 628 clock 60.3Hz 800x600 (0x285) 36.0MHz +HSync +VSync h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz v: height 600 start 601 end 603 total 625 clock 56.2Hz 640x480 (0x286) 31.5MHz -HSync -VSync h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz v: height 480 start 481 end 484 total 500 clock 75.0Hz 640x480 (0x287) 31.5MHz -HSync -VSync h: width 640 start 656 end 696 total 832 skew 0 clock 37.9KHz v: height 480 start 481 end 484 total 520 clock 72.8Hz 640x480 (0x288) 25.2MHz -HSync -VSync h: width 640 start 648 end 744 total 800 skew 0 clock 31.5KHz v: height 480 start 482 end 484 total 525 clock 60.0Hz 640x480 (0x289) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz <SNIP> HDMI-0 connected 1280x720+0+0 (0x28c) normal (normal left inverted right x axis y axis) 708mm x 398mm Identifier: 0x28b Timestamp: 56641 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 1 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff003674121161b90b03 310f0103804628782a3f44a654469924 13484bbfee0001010101010101010101 010101010101011d00bc52d01e20b828 5540c48e2100001e000000fd00384c1f 3d08000a202020202020000000ff0035 32353030303030300a202020000000fc 00564342347878785f414d3030300155 02031871451112931401230907078301 000065030c001000011d80d0721c1620 102c2580c48e2100009e8c0ad0902040 31200c405500c48e210000188c0ad090 204031200c405500138e210000180000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000007 SignalFormat: TMDS supported: TMDS ConnectorType: HDMI ConnectorNumber: 1 (0x00000001) _ConnectorLocation: 1 (0x00000001) 1280x720 (0x28c) 74.2MHz +HSync +VSync *current +preferred h: width 1280 start 1720 end 1760 total 1980 skew 0 clock 37.5KHz v: height 720 start 725 end 730 total 750 clock 50.0Hz 1920x1080 (0x28d) 74.2MHz +HSync +VSync Interlace h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz v: height 1080 start 1084 end 1094 total 1124 clock 25.0Hz 1024x768 (0x27f) 78.8MHz +HSync +VSync h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz v: height 768 start 769 end 772 total 800 clock 75.0Hz 1024x768 (0x280) 75.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz v: height 768 start 771 end 777 total 806 clock 70.1Hz 1024x768 (0x281) 65.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 800x600 (0x282) 49.5MHz +HSync +VSync h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz v: height 600 start 601 end 604 total 625 clock 75.0Hz 800x600 (0x283) 50.0MHz +HSync +VSync h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz v: height 600 start 637 end 643 total 666 clock 72.2Hz 800x600 (0x284) 40.0MHz +HSync +VSync h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz v: height 600 start 601 end 605 total 628 clock 60.3Hz 800x600 (0x285) 36.0MHz +HSync +VSync h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz v: height 600 start 601 end 603 total 625 clock 56.2Hz 720x576 (0x28e) 27.0MHz -HSync -VSync h: width 720 start 732 end 796 total 864 skew 0 clock 31.2KHz v: height 576 start 581 end 586 total 625 clock 50.0Hz 640x480 (0x286) 31.5MHz -HSync -VSync h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz v: height 480 start 481 end 484 total 500 clock 75.0Hz 640x480 (0x287) 31.5MHz -HSync -VSync h: width 640 start 656 end 696 total 832 skew 0 clock 37.9KHz v: height 480 start 481 end 484 total 520 clock 72.8Hz 640x480 (0x289) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz 640x480 (0x28f) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

6 11

[opensuse] rsyslog drops thousands of messages.
by Carlos E. R. 04 Oct '12

04 Oct '12

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 When I fetch mail with fetchmail, I see this: <5.6> 2012-09-12 17:09:03 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:07 Telcontar rsyslogd-2177 - - - imuxsock lost 187 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:09 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:13 Telcontar rsyslogd-2177 - - - imuxsock lost 226 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:15 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:19 Telcontar rsyslogd-2177 - - - imuxsock lost 144 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:21 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:25 Telcontar rsyslogd-2177 - - - imuxsock lost 248 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:27 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:31 Telcontar rsyslogd-2177 - - - imuxsock lost 196 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:35 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:37 Telcontar rsyslogd-2177 - - - imuxsock lost 119 messages from pid 21238 due to rate-limiting The PID is that of fetchmail. How can avoid that? This is with openSUSE 12.1 - -- Cheers, Carlos E. R. -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.18 (GNU/Linux) iEYEARECAAYFAlBQpsQACgkQtTMYHG2NR9XAKACfXrYylbVLZUuJsFaMnxBUYdFk pO0An3FzGU4XJHgyR/lqJO0oXpW/38no =x9Hz -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

11 49

[opensuse] Lenovo G470 intermittent Boot problem
by Marco Calistri 01 Oct '12

01 Oct '12

Hello openSUSers, First of all this post could be classified as Out-of-topic since it is not related upon operating system issues but just on hardware or possibly system firmware, but I would like to try if somebody could provide useful suggestions regarding a very strange problem I am facing out on my Lenovo G470 notebook. Whenever I try to boot the machine after it was powered off since several hours, it fails repeatedly, I see just the power-on and battery led on, no screen bios information at all nor hdd activity, just a blank screen. By insisting several times to power on, then suddenly it boots showing bios menu and finally the operating system went initialized (Windows 7 in this case). Sometimes happens that after few minutes the system shut-down spontaneously and reboot itself but normally after this random behaviour it stays on stable and working perfectly until I power-off. I already opened a maintenance ticket with Lenovo and I am ready to deliver my notebook to authorized center for repair but I would like to know if somebody could guess which kind of failure may be causing this issue. Thanks. Regards, -- Marco Calistri (amdturion) opensuse 12.2 (Mantis) 64 bit - Kernel 3.4.6-2.10-desktop Gnome 3.4.2 Intel® Core™ i5-2410M CPU @ 2.30GHz × 4 - Intel® Sandybridge Mobile -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 4

[opensuse] Boot Probs with Opensuse 12.2
by Phil Savoie 01 Oct '12

01 Oct '12

Hi All, I just installed subject but find it will not boot unless the insstall dvd is in the drive and I point to HD install. The machine will not boot otherwise. My hd setup is as follows: quartz:~ # fdisk -c -u -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x000de2de Device Boot Start End Blocks Id System /dev/sda1 * 2048 1953525167 976761560 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ef674 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0000d7b1 Device Boot Start End Blocks Id System /dev/sdc1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sdc2 206848 1953521663 976657408 7 HPFS/NTFS/exFAT Disk /dev/sdd: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003f878 Device Boot Start End Blocks Id System /dev/sdd1 * 2048 108843007 54420480 83 Linux /dev/sdd2 108843008 117229567 4193280 82 Linux swap / Solaris quartz:~ # This is a dual boot machine with Win7 and opensuse 12.2. The fstab is such: quartz:~ # cat /etc/fstab /dev/disk/by-id/ata-OCZ_VERTEX_PLUS_7CV2X9MIAFB9YWK3X70D-part2 swap swap defaults 0 0 /dev/disk/by-id/ata-OCZ_VERTEX_PLUS_7CV2X9MIAFB9YWK3X70D-part1 / ext4 acl,user_xattr 1 1 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WCAV55329683-part2 /dos ntfs-3g users,gid=users,fmask=133,dmask=022,locale=en_US.UTF-8 0 0 /dev/sda1 /home ext4 acl,user_xattr 1 2 /dev/sdb1 /iso ext4 acl,user_xattr 1 2 proc /proc proc defaults 0 0 sysfs /sys sysfs noauto 0 0 debugfs /sys/kernel/debug debugfs noauto 0 0 usbfs /proc/bus/usb usbfs noauto 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 quartz:~ # Any help would be great!! Thank you, Phil -- Carpe Aptenodytes! (Seize the Penguins!) -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

8 17

Re: [opensuse] chkconfig and systemctl
by Carlos E. R. 01 Oct '12

01 Oct '12

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On 2012-09-29 00:07, Greg Freemyer wrote: > > On Fri, Sep 28, 2012 at 5:43 PM, Carlos E. R. wrote: > Over the years (decades), I done a lot of things with Unix/Linux, but I don't recall ever > having a need to run a service in 3, that I couldn't run in 5. Then look again: gpm :-) - -- Cheers / Saludos, Carlos E. R. (from 12.1 x86_64 "Asparagus" at Telcontar) -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.18 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://www.enigmail.net/ iEYEARECAAYFAlBmJNoACgkQIvFNjefEBxoDxQCgnMDsV2vZXZ8UEmfPTCArDqIA YJkAniU5/5tzKafR1ND6A6U20hXkMn1l =G2aa -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

7 21

[opensuse] Missing separate debuginfo for - GDB
by Anisha Kaul 01 Oct '12

01 Oct '12

Greetz, I have mentioned `-g` option along with `-Wal`l in the Makefile. When I run `gdb onlineSunday`, I get: ----------------------------------------- Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_dds.so Try: zypper install -C "debuginfo(build-id)=a84a1969b9a69361b10f26814c0958717c48d671" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_eps.so Try: zypper install -C "debuginfo(build-id)=81e00b39aa9b3f7af23bad9d5bcef9f7cfe6333e" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_exr.so Try: zypper install -C "debuginfo(build-id)=0101355f5aa48dca9cf2723c94d1a4b7eb21e2ec" Missing separate debuginfo for /usr/lib64/libIlmImf.so.6 Try: zypper install -C "debuginfo(build-id)=f26997841c2902a0db04726d4018640cf367101e" Missing separate debuginfo for /usr/lib64/libIex.so.6 Try: zypper install -C "debuginfo(build-id)=2af205c15500875184d2b8519dbe01404bdfb3ae" Missing separate debuginfo for /usr/lib64/libHalf.so.6 Try: zypper install -C "debuginfo(build-id)=5134d1c2dc3c6ea90b5eeabd518eb746c853b87c" Missing separate debuginfo for /usr/lib64/libIlmThread.so.6 Try: zypper install -C "debuginfo(build-id)=ebb1d12661df5bbf0dd39c7c717cd197ada35d98" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_jp2.so Try: zypper install -C "debuginfo(build-id)=c1c25e24a14a9ec9163d623c699b6b53b7a1aabc" Missing separate debuginfo for /usr/lib64/libjasper.so.1 Try: zypper install -C "debuginfo(build-id)=d521bb2892ccef13f28afaa82c0ef48433e46ca5" Missing separate debuginfo for /usr/lib64/libjpeg.so.62 Try: zypper install -C "debuginfo(build-id)=c3638afbf013f8e33beaa3dc12f4d2dbdb3f8602" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_pcx.so Try: zypper install -C "debuginfo(build-id)=d1b443e7a29dd71a2519d852057c814bcfc9c30b" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_pic.so Try: zypper install -C "debuginfo(build-id)=4d533a04cab4426beaf2ae3c89eb2e026e5e1f81" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_psd.so Try: zypper install -C "debuginfo(build-id)=39ff79c31ae413ebac40eb8baef54ac524886e57" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_ras.so Try: zypper install -C "debuginfo(build-id)=7ecf3f8738c8cfacb14b6e54b53526346513dc8b" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_rgb.so Try: zypper install -C "debuginfo(build-id)=fc5d771438bc73014a4d551eb3b996043729c625" Missing separate debuginfo for /usr/lib64/kde4/plugins/imageformats/kimg_tga.so ----------------------------------------- The package I have already installed: ----------------------------------------- linux-trra:~ # cnf debuginfo-install Program 'debuginfo-install' is present in package 'yum-utils', which is installed on your system. Absolute path to 'debuginfo-install' is '/usr/bin/debuginfo-install'. Please check your $PATH variable to see whether it contains the mentioned path. ----------------------------------------- The system I have: ----------------------------------------- linux-trra:~ # [B]cat /etc/issue && uname -a[/B] Welcome to openSUSE 11.4 "Celadon" - Kernel \r (\l). Linux linux-trra 2.6.37.1-1.2-desktop #1 SMP PREEMPT 2011-02-21 10:34:10 +0100 x86_64 x86_64 x86_64 GNU/Linux ----------------------------------------- Question: What are the packages which do the trick? I searched Google for "debuginfo for kde4" - several links for several packages were shown. Do I have to hunt each one of them and install them separately? -- Anisha Kaul -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 3

[opensuse] OpenSuse 11.4 and bad Java installs
by James D. Parra 01 Oct '12

01 Oct '12

Hello, I've have wrecked my Java build on my 11.4 box and I am having a hell of time getting it to work properly. After installing and uninstalling each of the following; jre-6u35-linux-x64-rpm.bin, jre-7u7-linux-i586.rpm, jre-7u7-linux-x64.rpm, ...,I finally installed openjdk and its corresponding plugin to finally get some java capabilities in my browsers, Firefox, etc. However, I still get javascript errors on many webpages and I am almost at wits end. I would like to start from scratch by uninstalling all instances of Java and clean up /etc/alternatives, or whatever needs to be done to get a nice clean, properly linked java install with the browser plugins working properly. Could someone point me to a link or howto that can show me how to accomplish this? Many thanks in advance, James -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 4

[opensuse] Removable Hard Drive not mounting
by Jeffrey L. Taylor 30 Sep '12

30 Sep '12

I am reasonably certain I used my USB hard drive at least once to back up after upgrading with "zypper dup" from 11.4 to 12.2. But starting yesterday, no notification when I plug it in. Relevant /var/log/messages section below. Any recommendation on how to fix it? TIA, Jeffrey ep 30 03:00:56 viajero kernel: [ 746.400933] usb 2-1.1: new high-speed USB device number 3 using ehci_hcd Sep 30 03:00:56 viajero kernel: [ 746.487507] usb 2-1.1: New USB device found, idVendor=18a5, idProduct=0400 Sep 30 03:00:56 viajero kernel: [ 746.487518] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Sep 30 03:00:56 viajero kernel: [ 746.487525] usb 2-1.1: Product: USB 3.0 Desktop HD Sep 30 03:00:56 viajero kernel: [ 746.487529] usb 2-1.1: Manufacturer: Verbatim Sep 30 03:00:56 viajero kernel: [ 746.487533] usb 2-1.1: SerialNumber: 306215181776 Sep 30 03:00:56 viajero mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1" Sep 30 03:00:56 viajero mtp-probe: bus: 2, device: 3 was not an MTP device Sep 30 03:00:56 viajero kernel: [ 746.574665] Initializing USB Mass Storage driver... Sep 30 03:00:56 viajero kernel: [ 746.574745] scsi6 : usb-storage 2-1.1:1.0 Sep 30 03:00:56 viajero kernel: [ 746.574799] usbcore: registered new interface driver usb-storage Sep 30 03:00:56 viajero kernel: [ 746.574800] USB Mass Storage support registered. Sep 30 03:00:56 viajero dbus-daemon[750]: **** scsi_host ADDING /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/scsi_host/host6 Sep 30 03:00:56 viajero dbus-daemon[750]: **** scsi_host IGNORING ADD /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/scsi_host/host6 Sep 30 03:01:01 viajero /USR/SBIN/CRON[4180]: (jeff) CMD (cd /home/jeff/Rails/amethyst2production; nice -n1 /home/jeff/.rvm/bin/rake-ruby-1.8.7-head ts:reindex RAILS_ENV=development > /dev/null) Sep 30 03:01:03 viajero kernel: [ 752.755143] scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 6 Sep 30 03:01:03 viajero kernel: [ 752.755355] sd 6:0:0:0: Attached scsi generic sg2 type 0 Sep 30 03:01:03 viajero kernel: [ 752.758254] sd 6:0:0:0: [sdb] Write Protect is off Sep 30 03:01:03 viajero kernel: [ 752.758258] sd 6:0:0:0: [sdb] Mode Sense: 1f 00 00 08 Sep 30 03:01:03 viajero kernel: [ 752.759014] sd 6:0:0:0: [sdb] No Caching mode page present Sep 30 03:01:03 viajero kernel: [ 752.759017] sd 6:0:0:0: [sdb] Assuming drive cache: write through Sep 30 03:01:03 viajero kernel: [ 752.764255] sd 6:0:0:0: [sdb] No Caching mode page present Sep 30 03:01:03 viajero kernel: [ 752.764258] sd 6:0:0:0: [sdb] Assuming drive cache: write through Sep 30 03:01:03 viajero kernel: [ 752.764260] sd 6:0:0:0: [sdb] Attached SCSI disk Sep 30 03:01:03 viajero udisksd[3136]: Error opening /etc/crypttab file: Failed to open file '/etc/crypttab': No such file or directory (g-file-error-quark, 4) Sep 30 03:01:03 viajero dbus-daemon[750]: **** ADDING /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:01:03 viajero dbus-daemon[750]: **** UPDATING /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:01:03 viajero dbus-daemon[750]: **** ADDED /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:01:03 viajero dbus-daemon[750]: **** EMITTING ADDED for /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:02:01 viajero /USR/SBIN/CRON[4225]: (jeff) CMD (cd /home/jeff/Rails/amethyst2production; /home/jeff/.rvm/bin/ruby-1.8.7-head enqueue_refresh.rb) Sep 30 03:03:09 viajero kernel: [ 878.914637] usb 2-1.1: USB disconnect, device number 3 Sep 30 03:03:09 viajero dbus-daemon[750]: **** scsi_host IGNORING REMOVE /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/scsi_host/host6 Sep 30 03:03:09 viajero dbus-daemon[750]: **** REMOVING /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:03:09 viajero dbus-daemon[750]: **** EMITTING REMOVED for /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdb Sep 30 03:03:28 viajero systemd-tmpfile[4253]: stat(/run/user/jeff/gvfs) failed: Permission denied -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 2

Fwd: Re: [opensuse] chkconfig and systemctl
by General Mail 30 Sep '12

30 Sep '12

-------- Original Message -------- Subject: Re: [opensuse] chkconfig and systemctl Date: Fri, 28 Sep 2012 15:43:33 -0400 From: General Mail <general(a)bombshellz.net> To: Andrea Turrini <andrea.turrini(a)gmail.com> On 9/28/2012 8:03 AM, Andrea Turrini wrote: > 2012/9/28 Cristian Rodríguez <crrodriguez(a)opensuse.org>: >> El 28/09/12 05:13, eddie escribió: >> >>> Is chkconfig now obselete? >> >> Yes. > > Just two questions: > 1) Where is this documented? I have not seen it in the oS 12.2 release notes. > 2) How can I enable a systemd service only in runlevel 3 and not in > runlevel 5? If I try by using "yast2 runlevel", expert mode, I am > allowed to mark only 3 and not 5, but then 5 is enabled as well, when > the service file is present (tried with rpcbind). If the service file > is not present but only the init file is available, as for gpm, > everything works as expected. > > In particular, for the second question, please give a concrete answer > to the question such as a list of commands to obtain the wanted result > (list of commands that should be included in the release notes). > > Best, > Andrea > The concept of runlevels is obsolete in systemd from what I understand. Systemd works with 'units' and/or 'targets'. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

4 5

[opensuse] How does grub2-makeconfig determine what Linux kernels are recovery one's or not?
by General Mail 30 Sep '12

30 Sep '12

Hello, I am fiddling with openSUSE 12.2 GRUB2 attempting to boot a specific Kernel version. According to http://doc.opensuse.org/documentation/html/openSUSE/opensuse-reference/grub…, I ran 'grub2-makeconfig' to create the new boot entries, I am aware that latest Kernel will be placed on top of the list descending with the oldest Kernel, the specific Kernel I like to boot by default is set with recovery options. Is this by design? Furthermore, it states that I can specify the default boot entry with 'grub2-set-default' but this is useless if 'grub2-makeconfig' sets the Kernel I like to boot with recovery options. Any assistance on this matter would be greatly appreciated. Best Regards -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 4