Hi all,
Reading some mails on the GIMP mail list, I ran across the procedure
to install some more fonts for not only Gimp, but the system and
StarOffice to use also. Well, I installed the fonts, went to the
shell and issued the command xset fp+ <font directory> and then the
rehash command and all fonts are there! Ok, that went well, but each
time I restart the system, I have to do it all over again? Is there
a way to make it permanent and read the new fonts like it does the
ones the system installs or is that a no-no?
end of line
Tracer
Shell commands:
xset fp+ <new font directory>
xset fp rehash
--
---KMail 1.2--- SuSE Linux v7.2---
Registered Linux User #225206
/tracerb(a)sprintmail.com/ *Magic Page Products*
*Team Amiga* http://home.sprintmail.com/~tracerb
Hi,
I'dd like to know what the following files in the directory /boot are about.
Can anyone give me a clue or point me to some documentation?
- boot.b
- chain.b
- map
- System.map-2.2.14
- chos.*
Thanks in advance,
Sander
**********************************************************************
Disclaimer
This email is confidential and intended solely for the use of
the individual to whom it is adressed. Any views or opinions
presented are solely those of the author and do do not
necessarily represent those of the Azlan Holdings bv and/or
subsidairy. If you are not the intended recipient, be advised
that you have received this email in error and that any use,
dissemination, forwarding, printing or copying of this email
is strictly prohibited
If you have received this email in error please notify
Azlan Holdings MIS Helpdesk by telephone on
+31 (0) 79 3443200.
*********************************************************************
--
To unsubscribe send e-mail to suse-linux-e-unsubscribe(a)suse.com
For additional commands send e-mail to suse-linux-e-help(a)suse.com
Also check the FAQ at http://www.suse.com/support/faq
Before I do research on how to do this, it is possible to do this right,
> on a 2 drive box, with SUSE 8.0 on 1 drive, Debian and 98se splitting
> the other? I'm already dual booting fwiw..
>
> Thank you for your time.
Speaking of time, please check yours. Your email showed up with a date of
March 2, 1999...
Thanks,
Stan
Yes, I'm a time traveler you see, I'm only in this time segment now to check
on a few stock investments I had in mind...thanx for the tip Stan..
Lee :-)
Before I do research on how to do this, it is possible to do this right, on a
2 drive box, with SUSE 8.0 on 1 drive, Debian and 98se splitting the other?
I'm already dual booting fwiw..
Thank you for your time.
I am currently using a Dell 2650 Poweredge server without a raid controller. It's using the standard adaptec onboard SCSI as it stands. I'm wondering if anyone has installed the Perc3 raid controller and had the Linux install just pop right up (assuming the megaraid module was loading)?
I wouldn't need to reformat if all I was doing was switching controllers and hardware mirroring, right?
Thanks,
Rich
shado(a)mc.net
Greetings!
I'm thinking about getting an APC Back-UPS CS 350VA USB to automatically
shutdown my small file/DSL/firewall server (AOpen micro-ATX motherboard,
Cyrix M2-333Mhz, 128MB, 10GB IDE hard drive, SCSI cdrom drive, and no monitor).
Does anyone have any experience with this particular UPS?
Does the stock SuSE 7.3 kernel support a USB UPS or do I have to hack and
patch the kernel to make it work?
Recommend a similar model with serial support for under $100 USD?
Thanks!
Christopher Reimer
Hello
I have basically a suse samba server setup. Eth0 is for the internet
connection (cable). Eth1 is my internal network. I use eth1 for my samba
server. When i have the shares/ drive letters mapped, whatever, Ill goto
access them and that computer will just lockup or timeout for about 1
minute, then it will resume operation normally. I have approx. 5 comptuers
on the suse server, and they all do this from windows xp to windows 98se. I
am using set up addresses of 192.168.0.x, where is greater than 2. My
question is have or is there something Ive setup wrong to cause this pause
to occur. ? Its becomming very annoying..and frustrating. Im using kernel
2.4.18-64GB-SMP with a dual processor setup. If anyone has any ideas please
let me know. Every package installed is orginal versions from the suse
install cdroms. (no updates done).
Anything come to mind. btw, ive replaced the switch, with a new netgear one,
and all the networks at startech ST100 Realtek 8139 chipsets on 100Tx.
Anyone... !
Imagine the following situation:
- computer 1 has linux running and there is a vfat partition mounted
- computer 1 is running samba on that vfat partition (i.e. the vfat
partition is a share of samba)
- computer 2 wants to have write acces on the samba share
The problem is, that computer 2 has no write acces, because the vfat
partition is mounted 755.
The samba.conf file is the following:
[public]
comment = Schreibbares Verzeichnis
path=/home/sure/netzwerk/public
public=yes
readonly=no
browseable=yes
create mask=777
How can I make the partition mounted as mod 777 ? Thanks in advance !
Ulrich Schneider
Sorry for the cross post
All of a sudden my root password doesn't work. Looks like I've been
hacked (though the last time I ran YOU was three weeks ago) it's a
Firewall/Web system with ports 80,22,postgres open. Anyways I need to
know the command to boot lilo to super user mode.
Rowan Reid
Job Captain,
Systems Administrator
STUDIO 3 ARCHITECTS
909 982 1717