April 2015 - openSUSE Users - openSUSE Mailing Lists

Re: [opensuse] GRUB hangs after cloning root partition from one machine to another machine
by Keith Roberts 18 Apr '15

18 Apr '15

On 17 Apr 2015, at 15:49, Andrei Borzenkov <arvidjaar(a)gmail.com> wrote: > On Fri, Apr 17, 2015 at 3:08 PM, Keith Roberts > <keith.roberts(a)ecric.nhs.uk> wrote: >> Hi all. >> >> I used Clonezilla to make a backup of a suse 12.3 root and home partition on a production machine OK. A Dell PowerEdge R240. >> >> Previous to that on an identical test machine, I was able to make snapshots of sda2 + sda3, and restore these partitions again to that same test machine, and it booted OK from the GRUB prompt. >> >> So that was my DR plan in place and documented! >> >> Now I have used Clonezilla to make a snapshot of the production machine’s root and home partitions, and when I try to restore the root OS partition to the test machine I cannot even get a GRUB command line prompt. All I get is the word GRUB and a frozen command line. >> >> Can anyone shed some light on this please? >> > > GRUB encodes absolute disk location(s) in its primary boot block. If > these locations change (e.g. you restored on disk with different > geometry) grub will load garbage and execute it. With more or less > unpredictable results. Hi Andrei. Thanks for your reply. The disk UUID’s have changed so maybe that is the problem? Does grub use the disk’s UUID in it’s boot block? Kind Regards, Keith -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 1

[opensuse] imap, thunderbird and roundcube
by jdd 17 Apr '15

17 Apr '15

Hello, I have a curious problem with my mails. I have my own server with openSUSE (13.1), postfix, roundcube and imap/dovecot In Ropundcube, I have a "sent" folder and an "sent-archive" folder where I sorted the old sent mails by year in thunderbird, with the very same account, I only have one sent folder with all the mails in it. how is this possible? thanks jdd -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

8 21

[opensuse] openoffice just stopped working on 13.1?
by David C. Rankin 17 Apr '15

17 Apr '15

All, I used openoffice earlier today, but now it is cratering? (no updates, etc, since that time) Rather than 'M$ reboot', I want to understand what is happening. Running it from the command line yields: /opt/openoffice4/program/swriter ~/Documents/law/fpth/turner/posttrial/response_motion-for-judgment_r1.odt Application Error Fatal exception: Signal 6 Stack: /opt/openoffice4/program/libuno_sal.so.3(+0x37a9a)[0x7f0faf016a9a] /opt/openoffice4/program/libuno_sal.so.3(+0x37bcc)[0x7f0faf016bcc] /opt/openoffice4/program/libuno_sal.so.3(+0x37c69)[0x7f0faf016c69] /lib64/libc.so.6(+0x35550)[0x7f0fadc67550] /lib64/libc.so.6(gsignal+0x39)[0x7f0fadc674c9] /lib64/libc.so.6(abort+0x148)[0x7f0fadc68958] /opt/openoffice4/program/libvcl.so(+0x1558b1)[0x7f0faa2948b1] /opt/openoffice4/program/libsofficeapp.so(+0x2350b)[0x7f0faed7550b] /opt/openoffice4/program/libvcl.so(+0x17ffd2)[0x7f0faa2befd2] /opt/openoffice4/program/libuno_sal.so.3(+0x36862)[0x7f0faf015862] /opt/openoffice4/program/libuno_sal.so.3(+0x37c4a)[0x7f0faf016c4a] /lib64/libc.so.6(+0x35550)[0x7f0fadc67550] /opt/openoffice4/program/libuno_cppu.so.3(+0x1854f)[0x7f0facd6e54f] /opt/openoffice4/program/libuno_cppu.so.3(uno_type_sequence_reference2One+0xcd)[0x7f0facd6ef9f] /opt/openoffice4/program/libutl.so(+0xe1b07)[0x7f0faa940b07] /opt/openoffice4/program/libutl.so(_ZN14SvtPathOptionsC1Ev+0xcc)[0x7f0faa9458ec] /opt/openoffice4/program/libsofficeapp.so(+0x38a1a)[0x7f0faed8aa1a] /opt/openoffice4/program/libsofficeapp.so(+0x3ac08)[0x7f0faed8cc08] /opt/openoffice4/program/libsofficeapp.so(+0x2c3b0)[0x7f0faed7e3b0] /opt/openoffice4/program/libvcl.so(+0x1808b7)[0x7f0faa2bf8b7] /opt/openoffice4/program/libvcl.so(_Z6SVMainv+0x1e)[0x7f0faa2bf982] /opt/openoffice4/program/libsofficeapp.so(soffice_main+0x9c)[0x7f0faeda6f6c] /opt/openoffice4/program/soffice.bin(main+0xb)[0x400f7b] /lib64/libc.so.6(__libc_start_main+0xf5)[0x7f0fadc53be5] /opt/openoffice4/program/soffice.bin(__gxx_personality_v0+0xb9)[0x400eb9] /opt/openoffice4/program/soffice: line 121: 9580 Aborted "$sd_prog/$sd_binary" "$@" I've looked through running processes and I cannot find any piece of AOO running. What should I check? -- David C. Rankin, J.D.,P.E. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 3

[opensuse] insane disk activity after resume?
by P.Suetterlin＠royac.iac.es 17 Apr '15

17 Apr '15

Hi, since I switched my Laptop to OS 13.2 with BTRFS as root filesystem, after each resume I see an insane disk activity on my system disk. The HD light is flashing permanently, and activating block dump logging gives entries like Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2067264 on sdb2 (96 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2067520 on sdb2 (32 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2067872 on sdb2 (32 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2068256 on sdb2 (320 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2068608 on sdb2 (160 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2068800 on sdb2 (128 sectors) Apr 17 08:31:06 snoopy kernel: kworker/u4:1(2540): WRITE block 2089472 on sdb2 (96 sectors) It really seems to be going through the *whole* disk (100G), it is currently still running, 1h 40 after resume. Does anyone have an idea *what* the reason for this is, or how I can try to find out? This is an SSD, so I'm definitely NOT amused about this massive writing (at least) two times per day. Pit -- Dr. Peter "Pit" Suetterlin http://www.astro.su.se/~pit Institute for Solar Physics Tel.: +34 922 405 590 (Spain) P.Suetterlin(a)royac.iac.es +46 8 5537 8507 (Sweden) Peter.Suetterlin(a)astro.su.se -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 2

[opensuse] GRUB hangs after cloning root partition from one machine to another machine
by Keith Roberts 17 Apr '15

17 Apr '15

Hi all. I used Clonezilla to make a backup of a suse 12.3 root and home partition on a production machine OK. A Dell PowerEdge R240. Previous to that on an identical test machine, I was able to make snapshots of sda2 + sda3, and restore these partitions again to that same test machine, and it booted OK from the GRUB prompt. So that was my DR plan in place and documented! Now I have used Clonezilla to make a snapshot of the production machine’s root and home partitions, and when I try to restore the root OS partition to the test machine I cannot even get a GRUB command line prompt. All I get is the word GRUB and a frozen command line. Can anyone shed some light on this please? I can run the restored OS to make changes using System Rescue CD, but I still obviously need to get the machine to boot from the GRUB command line. sda is a RAID-1 set divided into four primary partitions. sda1 swap sda2 / sda3 /home sda4 /other TIA Kind Regards, Keith Roberts-- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 1

[opensuse] wicked and network change
by P.Suetterlin＠royac.iac.es 17 Apr '15

17 Apr '15

Hi list, I recently upgraded (rather:re-installed) my system to 13.2, which first used NetworkManager for setting up the network. Though it was sort off annoying that I always had to restart my VPN after a hibernation, what really made me dump it was that several times after an zypper up it lost all connection to the device, and I ended up rebooting to return it to a sane state... So I changed to wicked (I'm not using wireless anyhow), and set up VPN via systemd. While this works fine, it behaves weird when I switch to a different (wired) network (as I do daily between home and work). The network is set for DHCP, and after boot I can see the IP address using ifconfig. But if I suspend and resume connected to the other network, ifcofig will still show the old address, allthough I can see in the system logs that DHCP has acquired a new address for that interface. Indeed, 'ip addr show' lists two: snoopy:~% ip addr show enp0s25 3: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 00:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 192.168.1.33/24 brd 192.168.1.255 scope global enp0s25 valid_lft forever preferred_lft forever inet xxx.xxx.xxx.23/24 brd xxx.xxx.xxx.255 scope global enp0s25 valid_lft forever preferred_lft forever I find this somehow - wicked. Is this the default/expected behavior? My old system (12.3) always had only one address active. Is there a way to get back to the old way? Thanks, Pit -- Dr. Peter "Pit" Suetterlin http://www.astro.su.se/~pit Institute for Solar Physics Tel.: +34 922 405 590 (Spain) P.Suetterlin(a)royac.iac.es +46 8 5537 8507 (Sweden) Peter.Suetterlin(a)astro.su.se -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 3

[opensuse] email server error messages
by Greg Freemyer 17 Apr '15

17 Apr '15

All, re: openSUSE 13.1 I've got a small email server I'm running. Basically it just accepts emails and forwards them out. There are some log entries that look like errors, but as far as I know all if good. Is there anything in the below I should be concerned with: == 2015-04-16T14:10:11.818306-04:00 cloud1 postfix/qmgr[2490]: 8882640B17: from=<greg.freemyer(a)gmail.com>, size=1826, nrcpt=1 (queue active) 2015-04-16T14:10:11.837883-04:00 cloud1 postfix/smtp[8625]: nss-ldap: do_open: do_start_tls failed:stat=-1 2015-04-16T14:10:11.839855-04:00 cloud1 postfix/smtp[8625]: nss-ldap: do_open: do_start_tls failed:stat=-1 2015-04-16T14:10:11.840523-04:00 cloud1 postfix/smtp[8625]: nss_ldap: could not search LDAP server - Server is unavailable 2015-04-16T14:10:11.841898-04:00 cloud1 postfix/smtp[8625]: nss-ldap: do_open: do_start_tls failed:stat=-1 2015-04-16T14:10:11.843674-04:00 cloud1 postfix/smtp[8625]: nss-ldap: do_open: do_start_tls failed:stat=-1 2015-04-16T14:10:11.844871-04:00 cloud1 postfix/smtp[8625]: nss_ldap: could not search LDAP server - Server is unavailable 2015-04-16T14:10:11.945653-04:00 cloud1 postfix/smtpd[8620]: disconnect from mail-wi0-f176.google.com[209.85.212.176] 2015-04-16T14:10:12.420081-04:00 cloud1 postfix/smtp[8625]: 8882640B17: to=<intelligentavatar(a)gmail.com>, orig_to=<mary.vidarte(a)iac-forensics.com>, relay=gmail-smtp-in.l.google.com[173.194.194.26]:25, delay=0.9, delays=0.29/0.03/0.2/0.37, dsn=2.0.0, status=sent (250 2.0.0 OK 1429207812 i6si16681180igv.54 - gsmtp) 2015-04-16T14:10:12.421492-04:00 cloud1 postfix/qmgr[2490]: 8882640B17: removed == The aove is an email from <greg.freemyer(a)gmail.com> to Mary.vidarte(a)IAC-forensics.com which is in turn forwarded to intelligentavatar(a)gmail.com. As I said, the process all works, it is just the various error messages I worry a little about. Thanks Greg -- Greg Freemyer -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 2

[opensuse] USB NIC issue
by Stevens 17 Apr '15

17 Apr '15

My systems 1 & 2: OS 13.1, KDE 4.11.5 One is 32 bit, one is 64 bit. >lsusb Bus 002 Device 009: ID 0b05:17ab ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter (rev. B1) [Realtek RTL8192CU] >lsmod |grep 8192 rtl8192cu 102305 0 rtl8192c_common 71013 1 rtl8192cu rtl_usb 18877 1 rtl8192cu rtlwifi 90192 2 rtl8192cu,rtl_usb mac80211 635601 3 rtl8192cu,rtl_usb,rtlwifi Each is using an Asus USB-N13 wireless NIC because of it being included in the Linux hardware compatability list. Both systems exibit the same behavior. OK, they work. Linux auto detects them and, after the NIC is configured via Yast, there is network connectivity. For a while. An indeterminate time, really. Maybe a few minutes, maybe and hour, maybe a day. It ain't the nic, it ain't the hardware, it has to be the operating system. I have applied updates but nothing has changed the behavior. Has anyone on the list run across this behavior before? It is quite frustrating. I have a workaround that keeps an su term open with "systemctl restart network.service" which re-initializes the nic but having to do that really sucks. The 32 bit system is at my grandkid's place and she is definitely computer challenged but she seems to understand the issue and is able to restart the networking when necessary. Fred -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] Re: Comcast exposing unconfigured ipv6 addrs for ipv4 static clients(was Re: mailservers and reverse DNS ?)
by Linda Walsh 17 Apr '15

17 Apr '15

James Knott wrote: > On 04/16/2015 05:35 PM, Linda Walsh wrote: >>>> Sorry for the confusion, but the 'ifconfig' was at the end of the >>>> previous >>>> email (repeating here): >>>> >>>> Ishtar:law> ifconfig eth2 >>>> eth2 Link encap:Ethernet HWaddr 00:26:B9:48:71:E2 inet >>>> addr:173.164.175.65 Bcast:0.0.0.0 Mask:255.255.255.248 >> --- >> The above lines are all there is **now**. > > I'm curious about that 0.0.0.0 broadcast address. That's normally for > the default route. Broadcasts are the top address of the subnet or, in > your case, 173.165.175.71 --- Good point. Will have to investigate that... not sure, but a microsoftism might have crept into my config somewhere...hmmm Thanks for the catch... -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

Re: [opensuse] Help with setting CPU frequency
by I.Petrov 17 Apr '15

17 Apr '15

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256 Hello Don, I was trying to reply you directly but comcast refuses to talk with my email server (they require all mail servers to have a PTR record with a valid reverse DNS entry). But to answer your question. Yes the patch is included in the kernel tree. See also this comment and the code below it in drivers/acpi/processor_perflib.c : ... /* ignore_ppc: * -1 -> cpufreq low level drivers not initialized -> _PSS, etc. not called yet * ignore _PPC * 0 -> cpufreq low level drivers initialized -> consider _PPC values * 1 -> ignore _PPC totally -> forced by user through boot param */ static int ignore_ppc = -1; module_param(ignore_ppc, int, 0644); MODULE_PARM_DESC(ignore_ppc, "If the frequency of your machine gets wrongly" \ "limited by BIOS, this should help"); ... which is related to bios_limit. I'm not a developer however and don't understand it ... sorry. Best Regards, I. Petrov On 04/12/2015 02:13 AM, don fisher wrote: > On 04/11/2015 03:56 PM, I.Petrov wrote: >> -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256 >> >> Hello, >> >> For more info regarding the bios_limit setting see here: >> >> http://kernel.opensuse.org/cgit/kernel/commit/?id=e2f74f355e9e2914483db10c0… >> >> Probably the limitation can be ignored with: >> >> echo 1 > /sys/module/processor/parameters/ignore_ppc >> >> or with processor.ignore_ppc=1 as kernel parameter at boot time. But I'm not sure about this. >> >> Best Regards, I. Petrov On 04/12/2015 12:29 AM, don fisher wrote: > > Thanks. Has that patch been included in the kernel tree, or as part of openSuse? Thanks again. > > Don > -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAEBCAAGBQJVKhCpAAoJEH8sJoKRFRU5dFsP/24tN761AiM64VeVTOBY7zxk tG+8PCHHFnXLDCqefedzeOVGgTaKJBTHs5D5fwxZWj+DDzuyBeI5XZgrh10QrqY8 mIXLtpzjrhXOMGuyLVP8dbNjxlEtxwntEOcvxyKPUDx50IDyhAi0irrJ0erbFw9i pzvzA/jjGGGzEsi4BApn6I/7z+Z8Qe1vH/ylt0iMPu8FLWRmdfrDkeUcZLC/Q0zb mL8+X2FpeaeRNGbKz3BRqoOjyU/Plo9IZByf+iNITWVfr/E4mq1GIdavdAPBxBJW PoszdyExC5nuawHCLqgdatAuUE7ka75I4cASMhWB4Wq502KyQs9FLpTTXmB7xSx6 ZAJ+PXUmANTzsIjKi0udMEIIXXBJcHAZsXMIY5iQVIz/nCsCXibQ/ex9NU7CLstX CjsSYZzRyosrt5sT/75EQUjhLaK+QoEouXfBPWhMnl1YyzyxIDZh0iEkPk87jt0D XWUj7xqWTpy4O/uyeYxX/+LncMQMhKTRv4ikwaj8nHOSOWuqS80S0uh4BtovyoKh G3VH9jhui9pq7vG1lDcgC+mLuJFRZ8DwH5qGRJvuMoGB8LzYc+ohxIkZswxnD75K PALMKo8+9qYHvo6jiJs8Stt/450CDN9b6oPuSjoH31C9itlrykrjok+CcSShqkHy 245/l2vPymTvFIqtUixN =cSZ7 -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

7 16