November 2011 - openSUSE Users - openSUSE Mailing Lists

[opensuse] 12.1 Konqueror File Manager opens in wrong directory
by James Knott 18 Nov '11

18 Nov '11

In openSUSE 12.1 KDE desktop, I use Konqueror instead of Dolphin for the file manager. However, for some reason it opens in ~/Documents, rather than in ~. Dophin opens in the correct subdirectory. Is there any way to change Konqueror to open in the correct subdirectory? tnx jk -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

8 20

[opensuse] Problems installing OpenSuSE 12.1 on HP DL380 [SOLVED]
by Claudio Prono 18 Nov '11

18 Nov '11

Hi to all, I have encountered some difficulties installing OpenSuSE 12.1 x64 on a HP DL380 Server. Douring the installation, no disks are detected. I have a bit investigated on this issue, and found an error into the /var/log/boot.log: <6>[ 1.921227] cciss 0000:04:03.0: PCI IRQ 51 -> rerouted to legacy IRQ 19 <6>[ 1.921262] cciss 0000:04:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 <4>[ 1.921363] cciss 0000:04:03.0: Controller reports max supported commands of 0, an obvious lie. Using 16. Ensure that firmware is up to date. <3>[ 2.004219] cciss 0000:04:03.0: Unable to get irq 19 for cciss0 <4>[ 2.004309] cciss: probe of 0000:04:03.0 failed with error -1 The solution i have found is specify noapic, acpi=off into the kernel parameters, and the system installs perfectly. After the installation, for booting the installed system i have also added noapic, acpi=off on the kernel boot parameters, or it don't boot. I have tested this problem only on the Kernel-desktop, the Kernel-default finish the boot without problems. Here is my lspci: 00:00.0 Host bridge: Intel Corporation E7520 Memory Controller Hub (rev 0c) Subsystem: Compaq Computer Corporation Device 3200 Flags: bus master, fast devsel, latency 0 Capabilities: [40] Vendor Specific Information: Len=05 <?> 00:02.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A (rev 0c) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=04, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: fde00000-fdffffff Prefetchable memory behind bridge: 0000000040000000-00000000400fffff Capabilities: [50] Power Management version 2 Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Capabilities: [64] Express Root Port (Slot-), MSI 00 Kernel driver in use: pcieport 00:06.0 PCI bridge: Intel Corporation E7520 PCI Express Port C (rev 0c) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0 Capabilities: [50] Power Management version 2 Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Capabilities: [64] Express Root Port (Slot+), MSI 00 Kernel driver in use: pcieport 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at 5000 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at 5020 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at 5040 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at 5060 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at fbef0000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00001000-00003fff Memory behind bridge: fbf00000-fcffffff Prefetchable memory behind bridge: 40100000-401fffff 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02) Flags: bus master, medium devsel, latency 0 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Compaq Computer Corporation Device 3201 Flags: bus master, medium devsel, latency 0, IRQ 255 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at 0500 [size=16] Memory at 40200000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: ata_piix 01:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA controller]) Subsystem: Compaq Computer Corporation Proliant Rage XL Flags: bus master, stepping, medium devsel, latency 64 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] I/O ports at 3000 [size=256] Memory at fbff0000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 40100000 [disabled] [size=128K] Capabilities: [5c] Power Management version 2 01:04.0 System peripheral: Compaq Computer Corporation Integrated Lights Out Controller (rev 01) Subsystem: Compaq Computer Corporation Device b206 Flags: medium devsel, IRQ 4 I/O ports at 1800 [size=256] Memory at fbfe0000 (32-bit, non-prefetchable) [size=512] Capabilities: [f0] Power Management version 2 01:04.2 System peripheral: Compaq Computer Corporation Integrated Lights Out Processor (rev 01) Subsystem: Compaq Computer Corporation Device b206 Flags: bus master, stepping, medium devsel, latency 64, IRQ 3 I/O ports at 3400 [size=256] Memory at fbfd0000 (32-bit, non-prefetchable) [size=2K] Memory at fbfc0000 (32-bit, non-prefetchable) [size=8K] Memory at fbf00000 (32-bit, non-prefetchable) [size=512K] [virtual] Expansion ROM at 40120000 [disabled] [size=64K] Capabilities: [f0] Power Management version 2 02:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge A (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=02, secondary=03, subordinate=03, sec-latency=64 Memory behind bridge: fde00000-fdefffff Capabilities: [44] Express PCI/PCI-X Bridge, MSI 00 Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [6c] Power Management version 2 Capabilities: [d8] PCI-X bridge device 02:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge B (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=02, secondary=04, subordinate=04, sec-latency=64 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 0000000040000000-00000000400fffff Capabilities: [44] Express PCI/PCI-X Bridge, MSI 00 Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [6c] Power Management version 2 Capabilities: [d8] PCI-X bridge device 03:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10) Subsystem: Compaq Computer Corporation NC7782 Gigabit Server Adapter (PCI-X, 10,100,1000-T) Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17 Memory at fdef0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [40] PCI-X non-bridge device Capabilities: [48] Power Management version 2 Capabilities: [50] Vital Product Data Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+ Kernel driver in use: tg3 03:01.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10) Subsystem: Compaq Computer Corporation NC7782 Gigabit Server Adapter (PCI-X, 10,100,1000-T) Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18 Memory at fdee0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] PCI-X non-bridge device Capabilities: [48] Power Management version 2 Capabilities: [50] Vital Product Data Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+ Kernel driver in use: tg3 04:03.0 RAID bus controller: Compaq Computer Corporation Smart Array 64xx (rev 01) Subsystem: Compaq Computer Corporation Smart Array 6i Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19 Memory at fdff0000 (64-bit, non-prefetchable) [size=8K] I/O ports at 4000 [size=256] Memory at fdf80000 (64-bit, non-prefetchable) [size=256K] [virtual] Expansion ROM at 40000000 [disabled] [size=256K] Capabilities: [d0] Power Management version 2 Capabilities: [dc] PCI-X non-bridge device Capabilities: [f0] Vital Product Data 05:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge A (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=05, secondary=06, subordinate=09, sec-latency=64 Capabilities: [44] Express PCI/PCI-X Bridge, MSI 00 Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [6c] Power Management version 2 Capabilities: [d8] PCI-X bridge device 05:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge B (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=05, secondary=0a, subordinate=0c, sec-latency=64 Capabilities: [44] Express PCI/PCI-X Bridge, MSI 00 Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [6c] Power Management version 2 Capabilities: [d8] PCI-X bridge device Codially, Claudio Prono. -- -------------------------------------------------------------------------------- Claudio Prono OPST System Developer Gsm: +39-349-54.33.258 @PSS Srl Tel: +39-011-32.72.100 Via Santorelli, 15 Fax: +39-011-32.46.497 10095 Grugliasco (TO) ITALY http://atpss.net/disclaimer -------------------------------------------------------------------------------- PGP Key - http://keys.atpss.net/c_prono.asc -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 1

[opensuse] OS12.1: Phonon configuration not remembered
by JC Francois 18 Nov '11

18 Nov '11

Hi, I just installed OS 12.1 and I am trying to configure the audio system to use Skype. I have a Cisco USB webcam with integrated microphone. To configure the sound capture device I go to: Personal Settings > Multimedia > Phonon > Audio Recording There I notice that my sound card (Internal Audio Analog Stereo) is in the top position and the Mic of the USB webcam (08b6 Analog Mono) is in second position. I then move up the "08b6 Analog Mono" to the first spot under "Audio Recording" and then do a "Apply Device List To..." and select everything. By doing so I now have "08b6 Analog Mono" in top spot for CaptureCommunication, CaptureRecording and CaptureControl. I click OK and close the Dialog box. I then make a Skype test call and I can not hear my own voice. If I go back to Personal Settings > Multimedia > Phonon > Audio Recording I notice that "Internal Audio Analog Stereo" is back in top spot in all categories and that the changes that I made earlier are gone. How can I make my changes stick? Thanks, /~jc -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 1

Re: [opensuse] Remote login - openSUSE 12.1
by James Knott 18 Nov '11

18 Nov '11

Michael S. Dunsavage wrote: > Could suse firewall be bouncing you back out? > No firewall on either computer. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] To: unsuspecting tumbleweed users
by Greg Freemyer 17 Nov '11

17 Nov '11

All, There is small flame thread going on in -factory related to Tumbleweed repo management. Anyone still on 11.4 / Tumbleweed should give it a read, but the critical thing is that before you run "zypper dup" the next time, you critically need to update your repos per: http://en.opensuse.org/SDB:Change_from_12.1_to_Tumbleweed HTH Greg -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 2

[opensuse] Re: [opensuse-factory] Re: 12.1 IPv6 addressing issue (solved)
by James Knott 17 Nov '11

17 Nov '11

Lew Wolfgang wrote: > thanks for the info. sounds like SuSE Linux has moved to the new > default for > IPv6 configuration. Win7 and OSX Lion both default to choosing (and > changing) > a private IPv6 address. that's what we are watching on the testbed > VLAN 44. > OSX changes the v6 address every 24 hours and keeps the previous > handful > active on the interface for some days. > > currently the v6 sweeper on V44 tries to keep the newest IPv6 > address registered > for a device in DNS and LDAP, assuming that it is the "today" or > "after reboot" > current address even though others may still show up in the neighbor > table on > the switch. your host is treated to the old v6 sweeper logic so > when it > saw a SLAAC address it registered that for him and it will stick. The random address will change, though I don't know when, other than rebooting does it. However, why do they insist on calling it "private", when it's not. It might be called a "privacy" address, as it makes it more difficult to trace, but it's still a public address that can be reached from the public internet. A private address is one that exists only on the local lan, such as the RFC1918 IPv4 addresses. The link local IPv6 addresses can serve the same function, as can other limited scope IPv6 addresses. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] Re: Help!!!! Can't Start Dovecot [SOLVED]
by eddie 17 Nov '11

17 Nov '11

Hi All Using info that I got from the web, I did "lsof | grep 110" and it revealed that I had cyrus imap installed. I uninstalled cyrus and then dovecot started. I hope the info will be of help to someone else. By the way, I don't recall actually installing cyrus so I'm assuming that it was somehow automatically installed when I did the upgrade. Eddie On Thu, 2011-11-17 at 10:18 +0000, eddie wrote: > Hi All > > I updated to opensuse 12.1 last night. All seem to go smoothly but > when I check my email server (dovecot 2) it wasn't running. > The log messages say that all the listening addresses are already in > use. I do not have apparmor installed which used to cause a problem > and I have ipv6 selected even though I don't have any ipv6 devises > which I understand not having it selected caused listening problems in > the past. > So everything seems okay but the logs state: > > dovecot[3383]: Starting dovecot Error: service(pop3-login): listen(*, > 110) failed: Address already in use > dovecot[3383]: Error: service(pop3-login): listen(::, 110) failed: > Address already in use > dovecot[3383]: Error: service(imap-login): listen(*, 143) failed: > Address already in use > dovecot[3383]: Error: service(imap-login): listen(::, 143) failed: > Address already in use > dovecot[3383]: Fatal: Failed to start listeners > > Any advice ... suggestion? Would be extremely grateful. > > Thanks > Eddie -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] 12.1...., nope!
by Linux Tyro 17 Nov '11

17 Nov '11

Hi, I have decided to NOT go with 12.1 even though it would be very fresh (after a few hours), but for learning purposes, the old one (11.4) is more than sufficient..... IF I am thinking wrong, please do let me know..... -- THX -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

12 28

[opensuse] openSUSE 12.1 & runlevel 4 with VBox Guest Additions?
by LLLActive＠GMX.Net 17 Nov '11

17 Nov '11

Hi all, openSUSE 12.1 in VirtualBox: ERROR with "Install Guest Additions" " insserv: Service syslog is missed in the runlevels 4 to use service xenstored" and fail to build the modules. runlevel 4? Found response by Adrian Schröter on 10 March 2011: http://lists.opensuse.org/opensuse-packaging/2011-03/msg00041.html :-) Dreiel -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 1

[opensuse] nautilus failure
by e-letter 17 Nov '11

17 Nov '11

Readers, How to solve this command terminal response: # nautilus Gtk-ERROR **: GTK+ 2.x symbols detected. Using GTK+ 2.x and GTK+ 3 in the same process is not supported Trace/breakpoint trap opensuse114 -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0