June 2007 - openSUSE Users - openSUSE Mailing Lists

[opensuse] SSH Login Message
by Bob 01 Jun '07

01 Jun '07

Does anyone know how to stop this message from being displayed when someone logs in using SSH sshd[26987]: pam_unix2: session started for user xxxx, service sshd -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

3 6

[opensuse] nVidia Video Card Advice Please
by Mike 01 Jun '07

01 Jun '07

I just recently replaced my motherboard with a newer board with PCIe support (AMD x2 Dual Core 5200+) and an integrated nVidia 6100 video adapter. The integrated adapter works and I was finally able to install the nVidia drivers for 3D support, but it leaves a lot to be desired. First off, it wasn't even recognized by OpenSUSE. It came up as a Vesa Framebuffer adapter and I couldn't change it. I ran "sax2 -r -m 0=nv" to get wide screen resolution from my monitor, then installed the nvidia drivers. It still shows up as a Vesa Framebuffer adapter even though the nVidia drivers are loaded. Also, I am getting extremely bad ghosting (shadowing) of my fonts which is especially noticeable while typing on a white background. I've tried adjusting the aliasing/anti-aliasing and changing to and from sub-pixel hinting with varying hinting styles, but so far I haven't come across the magic combination yet to get rid of the lousy looking fonts. I've got a MAG 22" wide screen LCD monitor and the setup with my old motherboard worked perfectly for me with a nVidia GeForce FX 5200 AGP card. My question is this: Is there something I may be missing in the setup of the integrated 6100 or should I just buy a separate PCIe 16x adapter? Which nVidia adapter would you folks recommend? I don't have a whole lot to spend on it at this point but would like something that works with 3D enabled and renders the fonts like my old 5200 did. I checked the HCL and found that the GeForce 7300LE PCIe is supposed to work properly with 10.2. Are any of you using that adapter and if so how is it working out for you? Thanks very much for your help. Mike -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

4 5

[opensuse] Wireless troubles in 10.2 installation
by Jos van Kan 01 Jun '07

01 Jun '07

<soapbox> Until recently I have shied away from replacing my rock solid 9.3 system with anything newfangled, but since support is probably going to stop in the foreseeable future I decided to do a parallell installation of 10.2, just to see if I would run into any trouble. The 10.2 distro I got from a DVD that was part of a "Linux special" of C'T (a German computer magazine, also appearing in a Dutch version in the Netherlands). Everything went smoothly, but for a major glitch in the configuration of the wifi card, that crippled the remainder of the installation (installing update repositories etc), in short, everything that requires an internet connection. I am the proud owner of a Belkin wifi card, that I use in 9.3 with ndiswrapper. It was duly identified in 10.2 and provided with the bcm43xx driver which made good sense to me, since the card has a Broadcom chip. But. 1. It said I had to download firmware before the installation could complete. That was kind of hard, since I had no internet connection. 2. Yast configured it as eth1, which struck me as strange (I'd expect wlan0) 3. Yast did not hand me an opportunity to enter ESSID and encryption key, with the result, that the wireless router was unreachable. After the installation (semi-)completed I ran ifconfig but the card was not listed. I entered essid and encryption key by hand using iwconfig and restarted the network, but still no joy. I rebooted 9.3 to look around at the Belkin site for firmware and found none. I googled for "suse 10.2 bcm43xx firmware" and found the (surprise!) opensuse site, that told a totally different story, viz, that I had to install "bcm43xx-fwcutter" from the "installation disc" and run "install_bcm43xx_firmware". That looked promising. The software appears to be, apparently for legal reasons, on the "add-on CD", which btw was part of the DVD the distro was on. Apparently the same legal reasons did not forbid that. :-) What boggles my mind, is that Yast says I have to download the stuff where it is on the DVD. (Probably should have checked the box Add from other sources, or some such description only understandable by someone who gets there for the umpteenth time) And that it cannot install it itself. I mean if the stuff is there, what the heck. Ask the user, or do something intelligent. Well, anyway, after I handcrafted the eth1 configuration file to include a couple of "WIRELESS" parameters like WIRELESS, WIRELESS_ESSID and WIRELESS_KEY and installed the online update directories I had basically a running system. I hate to think what would have happened, had I been a newbie trying linux for the first time. The problem is well known btw, as the 18700 google hits on "suse 10.2 bcm43xx firmware" testify. Among those a substantial amount consists of newbies being left stranded in the desert. The card does not run under knetworkmanager, but what else is new? </soapbox> Regards, -- Jos van Kan registered Linux user #152704 -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

2 1

[opensuse] vncserver access via putty but not from remote desktop sharing
by Alexander.Herr＠csiro.au 01 Jun '07

01 Jun '07

Hi list, I put this onto a new threat, since I bunged up the previous mail's threat... I am trying to use KDE desktop sharing. However I am unable to login into the remote desktop via http (time out error) or via remote desktop connection (Kwallet asks for a password but does not accept the invitation password). I have enabled Firewall access to ports etc. So what I would need is a how-to to that explains from scratch what other things need to be enabled to run desktop sharing. Also I cannot find the log file for the vnc server (none under /var/log/) - where would that be located and under what name. Oddly I can start vnc manually and tunnel into it via putty/tighvnc. The logfile than is in my home directory. Thanx Herry -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

3 4

[opensuse] Activating system root messages to /var/mail/'username'
by Registration Account 01 Jun '07

01 Jun '07

In version 10.1 part on the install had a small box during the stage of defining users "to receive System mail" These messages were sent to /var/mail/'username' and were in mbox format and could be read by your email client under a "local delivery" or "movemail" type server. In 10.2 I did not see the option as part of the install. Does anyone know where in Yast you go to to active these messages. If I have to revert to a command line then that's o.k to. Any clues or answers? Scott

3 2

[opensuse] where find recent binary PostgreSQL
by Andreas 01 Jun '07

01 Jun '07

Hi, is there a packet source for recent PostgreSQL binaries? I just finished installing OpenSUSE 10.2 and like to add PostgreSQL 8.2.4 instead of the provided 8.1.5. I'd rather go with something that is at least vaguely official. PostgreSQL.org has only binaries for fedora+redhat and I found only V8.2.0 on ftp.suse.com Any hope ? Regards A. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

1 0