November 2006 - openSUSE Users - openSUSE Mailing Lists

Re: [SLE] Upgrading RAM
by Doug McGarrett 01 Nov '06

01 Nov '06

At 09:46 PM 10/30/2006 +0530, Amit Joshi wrote: > >I want to upgrade my RAM from the current 256MB. >Now, I have heard that its wise to buy another 256MB chip and add it to the >computer. Then what is called as the "Dual RAM Implementation" will come >into effect, thus boosting the performance. > >I actually wished to buy another 512MB chip. Is it like 256Mb+256Mb will >deliver a better performance compared to a single 512MB chip? > >Regards, >Amit. > >-- >http://mckagan.googlepages.com > > I just bought a 512 M memory card from Crucial, after reading on their FAQ page that with modern computers, you can add a different size ram board to whatever is in there now. (If it turns out not to work, I'll pull out the 128 M and leave the 512 M.) So, if you buy a 512 M ram, you "should" be able to plug it in alongside the 256, and have 768 M. Their staff is knowledgeable, so if you read off the numbers on your existing RAM, they should be able to tell you if this will work. They'd really like to know the name of the computer, or the MOBO mfr., but they seem to be able to work around it, if you don't know. Their 800 number is 1-800-336-8915, 7am to 8pm mountain time, weekdays, 10am to 2pm Saturdays. They are owned by, and sell, Micron. Good luck, whatever you decide. --wa2say The RAM came and I installed it alongside the old, and it works. Is there a way to verify that the system is using it? The box does seem faster.

3 2

How do I block certain senders in Postfix?
by Jim Flanagan 01 Nov '06

01 Nov '06

Further to my post a few weeks or so ago, how do I block emails from being accepted by postfix. The emails in particular are from one of 2 different IP addresses. I suppose I could block only those 2, or perhaps the entire range if need be. I read a bit on this in the docs, but am unsure if I should make a "hash" for it, or use canonical, and if so, how. I do have a hash for check_recipient_access which is working great. But I don't know how to block a particular IP address for a sender. I'm running Suse 10.0, mostly standard postfix. Many thanks for any pointers. Jim Flanagan

2 6

How to install Posgresql8 on SLES9 ?
by Xn Nooby 01 Nov '06

01 Nov '06

How to install Posgresql8 on SLES9 ? I am trying to install Postgresql 8.1.4 on SLES 9. My SLES machine currently has the SP2 and SDK installed. The SLES9 machine also already has Postgresql 7.4.13 installed on it. I found some Postrgresql 8 RPMS for SLES 9 here: http://www.gtlib.gatech.edu/pub/suse/projects/postgresql/postgresql-8.1.4/s… and copied them to the directory /var/pos_814 Then I found some more instructions here: http://en.opensuse.org/Creating_YaST_Installation_Sources Which led me to enter these commands cd /var/pos_814 genIS_PLAINcache -f -r . gzip genIS_PLAINcache The gzip command gets an error because the file does not exist. In YAST I went to "Change Source of Installation" and added the "local directory" on dir:///var/pos_814// dir:///var/pos_814/ I didn't see any new Postgresql entries in the "Install and Remove Software" screen. So I tried some more things. This entry did not work either: on dir:///var/pos_814/ dir:///var/pos_814 I also tried running gzip on the "IS_PLAINcache" which turned it into IS_PLAINcache.gz, but it still did not work. Hopefully I will be able to add Postrgresql 8 to yast, and then have either the option of upgrading 7.4, or replacing it with 8. Any suggestions? I'm kind of new at SLES and Postgresql. Thanks!

1 0

Volume Controls show up but don't work
by Chris Forzetting 01 Nov '06

01 Nov '06

Hi all ~ My volume control (and the full kmix program) does not seem to affect the volume of many applications, including realplayer and other media players. Also, the application volume controls also don't always work... Any ideas? Using SuSE 10.1 on an HP Pavillion dv6105us laptop with centronix high-definition audio. Not on my suse boot right now so can't look up what the audio is listed as in yast... -- Chris Forzetting, Tech and Trainer _________________________________________________________________ " 'Think as I think,' said a man, 'or you are a toad.' And after I had thought of it, I said, 'I will then be a toad.' "

2 1

[opensuse] Verifying copied files - Global Settings and singular command switch
by Intrusion Detection Account 000 01 Nov '06

01 Nov '06

In DOS there was the ability to verify a singular files integrity by using chkdsk c:/file.dos......The result indicated if the file integrity was so. There was also the ability to set in the Autoexec.bat set verify=ON - which made sure that EVERY file that you copied you did not need to use the verify option C:\file.dos C:\temp\file.dos /v My questions are 1. Is there a global set verify=on in Linux? 2. Is there the ability to verify a single files integrity as above with a similar command such as chkdsk 3. How do I copy a file at the command line and include a verify option. The reason I ask is that I recently lost my home directory and I had KDAR backing up the /home directory every week to an NFS drive. When I came to restore the archive the files header was reported to be corrupted. Also as a backup I copied with Konqueror the /home directory to an NFS drive and some of the files are aslo now not readable due corruption. I have made an Enhancement report to both Konqueror and KDAR that they include a verify option like most backup programs. Over many years I have seen backups unable to be restored because verify was not turned on. Now its happened to me. I understand the file system in Linux is far superior in its disk I/O but I dont want to waste time backing up if I cannot ensure the files are intact. The current backup GUI's do not include a verify option and the only one that does 'cpio do not hav a GUI and due to the complexity of options available it is rather unfriendly. I have made a wish list item in opensuse to for someone to write a GUI for cpio which will also address a request to have the ability to backup to tape. regards to all from down under in OZ Scott

4 9

postfix configuration
by Geoffrey 01 Nov '06

01 Nov '06

I'm trying to modify my postfix configuration so that it will modify the sending domain. I've done this on my red hat box by setting the following in /etc/postfix/main.cf: main.cf:myhostname = www.3times25.net main.cf:mydomain = 3times25.net When I do the same on my SuSE box, it does not work. I know that there is a /etc/sysconfig/postfix configuration file on SuSE that does not exist on red hat, but I can't figure out if something there is overriding my settings in /etc/postfix/main.cf Anyone have any suggestions/insight? -- Until later, Geoffrey Those who would give up essential Liberty, to purchase a little temporary Safety, deserve neither Liberty nor Safety. - Benjamin Franklin

3 6

Re: [SLE] OT switch from comcast to roadrunner
by PerfectReign 01 Nov '06

01 Nov '06

On Tue, October 31, 2006 1:30 pm, William Gallafent wrote: > On Tuesday 31 October 2006 13:14, Geoffrey wrote: >> If this doesn't work, which >> it likely will not, you might try installing IE on Linux via >> wine or crossover office. > > Or perhaps IEs4Linux: http://www.tatanka.com.br/ I must add... ...I cannot believe how bloody quick that implementation is. I've run CX Office forever with IE being one of the main reasons. This version, though not planning on being my main browser, blows away the performance of the Crossover Office implementation. Good job, folks. Now we just need a quick and easy installation for us newbies. -- Kai Ponte www.perfectreign.com || www.4thedadz.com remember - a turn signal is a statement, not a request Thought for the day: There is more money being spent on breast implants and Viagra today than on Alzheimer's research. This means that by 2040, there should be a large elderly population with perky boobs and huge erections and absolutely no recollection of what to do with them. -- Kai Ponte www.perfectreign.com || www.4thedadz.com remember - a turn signal is a statement, not a request

3 8

[opensuse] hibernation issue
by Pol 01 Nov '06

01 Nov '06

Hi, I am trying to install opensuse 10.2 beta on a toshiba satellite laptop (it is refurbished, so i cannot find the model name). Installation completes smoothly, but i cannot find any hibernation command on the desktop (kde has been installed). Kernel is 2.6.18. Should i patch it, to get the hibernation feature? Thank you for your help -- Pol --------------------------------------------------------------------- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

2 1

[opensuse] LKCD
by Bill Anderson 01 Nov '06

01 Nov '06

I have been trying to get LKCD to work with little success on SUSE 10.1. When invoked by sysrq-D, it starts the dump but doesn't finish it. I notice that LKCD now uses kernel objects, and that it now expects a different configuration file. I haven't found any documentation on the new configuration file. Does LKCD still use the file in /etc/sysconfig? Bill Anderson --------------------------------------------------------------------- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

1 0

[opensuse] Updating 10.1
by kevin.kempter＠dataintellect.com 01 Nov '06

01 Nov '06

Hi List; I posted to the suse-linux-e list with no response. Maybe that was the wrong list to start with? Yesterday pulled down the remastered 10.1 DVD ISO and installed 10.1 on a laptop I have to see if Its ready for me to upgrade. The install went fine however I am somewhat confused by the new zen updater instead of my SuSE Watcher. So, I have a few questions: - Does the zen updater pull only patches & fixes like the SuSE Watcher did ? If not where do I now get these types of updates? - What's the best way to update my system, does the zen updater do it all ? or is there a better/easier to manage method? - Both zen updater and Yast Sources only list my DVD drive. Where can I find a list of 10.2 repositories for both the zen updater and yast ? Do they both accept the same repos? I guess the short question is - how do I keep my system up to date and where can I find step by step (im kinda slow) documentation on how to configure my new 10.1 box for updates? Thanks in advance... /Kevin --------------------------------------------------------------------- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

3 2