September 2005 - openSUSE Users - openSUSE Mailing Lists

Intel PRO/Wireless 2200BG under SuSE 9.2?
by Jesper Andersson 20 Feb '06

20 Feb '06

Dear everyone, I wonder if anyone has any experience of getting the wireless eth-card in a Dell Latitude D600 to work for SuSE 9.2? The card is an Intel PRO/Wireless 2200BG. It is recognised by the system as such, and I am able to configure it in Yast without any obvious problems. However, it doesn't get an IP-address. This is in contrast with the same laptop in the same location booting the XP partition, in which case it finds the network, gets an IP and chats away happily. The setup is the same for SuSE and XP: DHCP, named ssid, WEP-ASCII-5char encryption. The following may be relevant version numbers Kernel 2.6.8-24 wireless-tools 27pre26-10 ipw-firmware 3.3 During boot I get the following messages (some of which sound a bit omnious, but I am not certain how serious they are) that I interpret as related to the problem <4>ieee80211_crypt: unsupported module, tainting kernel. ("tainting is bad, right?") <7>ieee80211_crypt: registered algorithm 'NULL' <4>ieee80211: unsupported module, tainting kernel. . . <4>ipw2200: unsupported module, tainting kernel. <6>ipw2200: Intel(R) PRO/Wireless 2200 Network Driver, 0.8 <6>ipw2200: Copyright(c) 2003-2004 Intel Corporation . . <6>eth1: Setting MAC to 00:0e:35:ad:e3:81 <3>ipw2200: Calibration and the later on when trying to connect eth1 device: Intel Corp. PRO/Wireless 2200BG (rev 05) eth1 configuration: wlan-id-00:0e:35:ad:e3:81 ERROR: command 'iwconfig eth1 mode Managed' returned Error for wireless request "Set Mode" (8B06) : SET failed on device eth1 ; Operation not supported. eth1 (DHCP) . . . . . no IP address yet... backgrounding. waiting If anyone recognise the problem and has a solution to it I would be for ever grateful. Please also be gentle with me if/when replying. I am a bit of a beginner and don't handle jargon very well. Puss Jesper

7 6

External disk choice
by Maura Edelweiss Monville 11 Feb '06

11 Feb '06

I have a 4-year old DELL desktop with a heavy CRT monitor that I'm going to give away soon . I also have a 2 month old laptop. Both computers run Linux/SuSE. I would like to buy an external disk to save most of my s/w development now residing on my old desktop. But I would like to be able to use it also with my laptop. Both computers have some USB ports so I daresay an external USB disk would be fine .. I'd appreciate some suggestion about a USB reliable, large capacity but portable, external disk or any alternative solution. Thank you in advance. Maura

8 11

unsuscribe
by Linda Miller 07 Feb '06

07 Feb '06

unsuscribe

5 4

SCSI RAID recovery
by Robert Amodeo 19 Jan '06

19 Jan '06

I have a fileserver running SuSE 8.0 with 2 IDE Drives and a SCSI RAID (RAID5). The system boots up to one of the IDE drives, and the SCSI RAID drive runs as a mounted filesystem (/dev/md0). (all filesystems are REISERFS). Problem: The SCSI RAID drive has crashed (won't boot up), and I need to recover it (repair it, through some utility). Further: The software does not seem to want to mount the disks, even though the SCSI BIOS (Adaptec) recognizes the disks, and they are listed as OPTIMAL. I tried to repair the disk(s) (with reiserfsck), but it produced an error message: reiserfs_open: bread failed reading block 2 reiserfs_open: bread failed reading block 16 reiserfs_open: neither new nor old reiserfs form found on /dev/md0 The literature suggested that this error message is hardware related (either a disk is physically damaged, or maybe the RAID isn't recognized), but again, the disks are recognized (and therefore, so is the SCSI Card). I tried to boot up with SuSE CD 1 in Recovery mode, but not sure what to do there (i.e., after the root prompt - just run reiserfsck?). Literature suggests there are plenty of tools to handle disk recovery, and especially RAID support, I can't find reference to them anywhere. The installation of the RAID was trivial (using the YAST2 partitioning GUI window on startup), and yet recovery seems to be a mystery. This can't be right. Does anyone know where there are "decent" and "usable" recovery tools? OR ... does anyone know what "specifically" to do in this case? Can I re-partition without formatting, and recover the existing data? Any help is appreciated - I'm sure I'm missing something "obvious", but can't find "obviously" what to do in the literature, docs, etc. Thank you. Robert Amodeo School of Engineering and Applied Science University of California, Los Angeles

3 4

Using k3b
by Tim Hanson 08 Jan '06

08 Jan '06

I have a large jazz CD collection, a lot of which may not be available forever. I'm concerned with things I've read that CDs and DVDs may be subject to deterioration. I also know that CDs can also be damaged by scratches, etc. I'm familiar with and have successfully used the CD cloning utility of k3b to create a playable (with a standard CD player) duplicate CD, but I want to copy the entire image to my hard drive, so I can keep it there in case the original becomes unplayable later. I have no interest in creating a bunch of duplicate CDs, most of which will never be used in my lifetime. When I clone directly to my hard drive, the program created two files: k3b_0.img and k3b_0.img.toc. This is fine, but I can't figure out how to write this image to another CD. I've read the documentation that comes with the program without success. -- "Just once, I wish we would encounter an alien menace that wasn't immune to bullets" -- The Brigader, "Dr. Who" -- We cannot put the face of a person on a stamp unless said person is deceased. My suggestion, therefore, is that you drop dead. -- James E. Day, Postmaster General

18 46

Gizmo for SuSE 9.3
by Alfredo Cole 07 Jan '06

07 Jan '06

Hi: Is there a rpm package for SuSE 9.3? It seems to be targeted at debian-based systems only. Any other installation instructions would be welcome. Thank you. -- Alfredo J. Cole Grupo ACyC

3 3

9.3 Review
by David Johanson 06 Jan '06

06 Jan '06

Linux Magazine (Linux Pro in the US) has a 4 page review of the 9.3 release in the June 2005 issue, pgs 44-47. "Novell's Suse Linux 9.3 is a feature-rich, and robust Linux distribution. At first glance, the new version does not seem much changed from 9.2, but a lot of work has gone on under the hood. The distribution is definitely good for new users. If you already have Suse Linux 9.x or a similarly recent system, the update is only worth the effort if you are unhappy with your current setup. If you use external media on a regular basis, the update is definitely a good idea. . . . " dave -- David C. Johanson Linux Counter # 116410 Powered by SuSE Linux 7.3 People who behold a phenomenon will often extend their thinking beyond it; people who merely hear about the phenomenon will not be moved to think at all. -- Goethe

12 14

New machine problems, looking for culprits
by Paul Alfille 26 Dec '05

26 Dec '05

A new AMD64 bit machine, new SUSE 9.3, should be heaven. Machine hangs after a few minutes of use, but I can't tell why. I hope someone recognizes a problem part so I can address it. Parts: Motherboard: Asus A8V-E includes: Disk controller: VIA SATA and IDE drives Network: Marvell Yukon 88E8053 PCI-E gigabit sound, usb, firewire on board CPU: AMD Athlon64 XP3500+ Graphics: Gigabyte PCI-Express 6600GT (NX66T128D) Attempts: WinXP: Embarassingly stable. SuSE9.3 (64bit) crashes Fedora Core 4 64-bit crashes Ubantu64 crashes DamnSmallLinux (embedded under XP with QEMU) stable!!! Obviously SuSE is my choice. I keep trying online update, hoping that the system will stay up long enough to complete and that a fix is coming. Any thoughts? Paul Alfille

7 7

help for sight impaired people
by Doug McGarrett 09 Dec '05

09 Dec '05

Some weeks ago I inquired here about assistance for those who have difficulty seeing, as I am one, at present. I am effectively blind in the left eye and have cataract in the right. Some of this may be ameliorated in the future, some will probably not be. Nothing came back at all. The font in K-Mail out-going is about 8 point on my 17" screen, as is the font on the message names for the incoming mail. I have not been able to change this, altho the actual incoming message font I was successful in changing. I do not have access to my Windows machine at present, due to mechanical failure, and this is the only way I have to communicate. Is there no way to make SuSE Linux friendly to optically-challenged users? Please, someone, reply. --doug

8 9

PC running (SuSE 8.2 Pro / WinME) bootloader lilo -> grub
by Mick Higgins 08 Dec '05

08 Dec '05

Hi List, I have belatedly made the change from lilo to grub carefully converting my lilo config to grub'ese. It seems to work as expected. However, I have a couple of questions which I cannot track down in any off-line source (man, info, howto's etc.) and I am not able to trawl google or list archive with a time-limited unmetered dial-up connection at present. 1. In lilo I always used the boot-floppy option so as not to upset WinME. How do I do something similar in grub? 2. When the bootloader menu appeared in lilo I could interactively overide the default runlevel (ie: boot to runlevel 3 not 5) when necessary. How is this achieved in the grub menu? I will accept a URL to the appropriate list archive entry or web page. Apologies if this has been dealt with before. -- ** Message sent via KDE KMail v1.7.2 on SuSE Linux v8.2 ** Please reply in the format that this message is sent. ** Thanks.

6 5