December 2003 - openSUSE Users - openSUSE Mailing Lists

network with SUSE firewall
by michael norman 24 Jan '04

24 Jan '04

Hi I'm running SUSE 9.0. I have two boxes. Until recently I was using ntl cable broadband. I had a Vigor router two share the connection between the two boxes. I have now changed to UKFSN adsl which is currently offering 1mb connection for 27 GBP per month. Prblem is UKFSN uses PPPoA which my router doesn,t support. My question is can I use SUSE firewall to share the connection ? I think I would need to put another NIC in one of the boxes and connect the modem to that box then configure SUSE firewall to do the routing.. Is that possible ? Any help appreciated Mike

5 6

Firebird flash problem continues
by Jim Sabatke 19 Jan '04

19 Jan '04

I just loaded the new OSS soundcard driver for the patched kernel 2.4.21-144. I still crash on Flash sites (example: www.provia.com) with Firebird. I tried Mozilla, which used to crash with a "no Alsa driver" message, but now Mozilla won't run, with the following: "Error launching browser window:TypeError: Componnets.classes['@mozilla.org/appshell/component/browser/instance;1'] has no properties" This started with the fresh install of 9.0. I can't see why I need Alsa running, since it doesn't support my soundcard. I tried running Alsa with a device of /dev/null, and that suppressed the error message from Mozilla. BTW, if I remove the two flash files flashplayer.xpt and libflashplayer.so from the plugins directory, Firebird doesn't crash, I just can't load the Flash stuff. Any ideas? -- Jim Sabatke Hire Me!! - See my resume at http://my.execpc.com/~jsabatke Do not meddle in the affairs of Dragons, for you are crunchy and good with ketchup.

1 1

RE: [SLE] PCMCIA cardbus network card on 9.0
by GarUlbricht7＠netscape.net 13 Jan '04

13 Jan '04

Tim Nicholson <tim.nicholson(a)bbc.co.uk> wrote: >I have a Realtek RTL8139 based cardbus card 10/100 card which is >correctly identified under YAST2, and set up as eth-pcmcia automagically. > >Despite this the system doesn't then seem to know then how to use it. > >cardinfo simply recognises it as a cardbus card with no details, and >ifconfig does not list it as an interface. > >Plugging in an old Dynamode 10Mb card using the same eth-pcmcia driver >works fine! > >Any one know what to prod next? >-- Hi Tim, Did you check the SuSE FAQ's and "SuSE Help Center?" I did a search on "cardbus" on SuSE Help on my 8.1 box, and there was an article on "PCMCIA CardBus Cards not being detected" which then refers to Sourceforge article. Don't know if it will help for your 9.0 box, as it appears to be somewhat dated, However, it might give you some more ideas to try. HTH Gar -- "The IETF motto is 'rough consensus and running code'" -- Scott Bradner (Open Sources, 1999 O'Reilly and Associates) -- __________________________________________________________________ New! Unlimited Access from the Netscape Internet Service. Beta test the new Netscape Internet Service for only $1.00 per month until 3/1/04. Sign up today at http://isp.netscape.com/register Act now to get a personalized email address! Netscape. Just the Net You Need.

4 7

No fonts in kde, gnome after apt updating
by E.F.Maurer 12 Jan '04

12 Jan '04

I just recently ran a selective synaptic upgrade, everything except a few gnome packages that were going to replace ulb packages. I finished the upgrade in windowmaker because I was going to upgrade kde, logging into kde this morning k mail had no fonts. Konquror as well. the desktop however looked normal, it seems it's just kde apps. I tried gnome but gnome has no fonts anywhere. I ran SuSEconfig which didn't fix it. I have a edited sources.list base funktronics kde packman packman-i686 security update suser-rbos usr-local-bin wine Any ideas on how to get kde apps in kde, and gnome working again? Sorry if this has been asked but with my new job I can't read as much of the mail from this list as I used to. TIA -- E.F.Maurer Using SuSE 9.0 Pro

4 5

New to KMail
by H du Plooy 09 Jan '04

09 Jan '04

Quick question: I use Evolution at home and now KMail at work. In evolution, I press Ctrl+K to mark messages as read. What's the equivalent in KMail? Alt+M-K-R is really a bit long. Is there something shorter? The KMail handbook lists a couple of shortcuts, but it's really only a few and not what I'm looking for. Thanks Hans

3 3

Phone answering machine...
by Des Aubery 08 Jan '04

08 Jan '04

What software is available in SuSe 9.0 Professional to enable my system to act as a 'Phone Answering Machine'? Thanks in advance for your assistance. Des Aubery... (adTherm Technology - www.adtherm.com - info(a)adtherm.com) -- Best regards, Des Aubery... (The Home of Virtual Thermal Engineering) (adTherm Technology - www.adtherm.com - des(a)adtherm.com)

12 20

Samba printing problem from XP
by Mark Hounschell 07 Jan '04

07 Jan '04

I've got 3 boxes on a private net. 2 Linux 9.0 and one Windows-XP. One of the Linux boxes is setup as a Samba server/Cups server. From the Linux box I can print to the printer as follows cat /etc/fstab | lpr This works and causes the following to be written to the /var/log/cups/error_log file I [30/Dec/2003:06:24:01 -0500] Adding start banner page "none" to job 19. I [30/Dec/2003:06:24:01 -0500] Adding end banner page "none" to job 19. I [30/Dec/2003:06:24:01 -0500] Job 19 queued on 'hp_deskjet870' by 'markh'. I [30/Dec/2003:06:24:01 -0500] Started backend /usr/lib/cups/backend/parallel (PID 2116) for job 19. Or I can print via the smbclient command as such: cat /etc/fstab | smbclient "//softtail/hp_deskjet870" -c "print -" -N -W "HOME-NET" This also works and causes the following to be written to the /var/log/cups/error_log file. I [30/Dec/2003:06:25:42 -0500] Adding start banner page "none" to job 20. I [30/Dec/2003:06:25:42 -0500] Adding end banner page "none" to job 20. I [30/Dec/2003:06:25:42 -0500] Job 20 queued on 'hp_deskjet870' by 'nobody'. I [30/Dec/2003:06:25:42 -0500] Started filter /usr/lib/cups/filter/texttops (PID 2120) for job 20. I [30/Dec/2003:06:25:42 -0500] Started filter /usr/lib/cups/filter/pstops (PID 2121) for job 20. I [30/Dec/2003:06:25:42 -0500] Started filter /usr/lib/cups/filter/foomatic-rip (PID 2122) for job 20. I [30/Dec/2003:06:25:42 -0500] Started backend /usr/lib/cups/backend/parallel (PID 2123) for job 20. Yet when I try to print from an app on the XP box I get this in the /var/log/cups/error_log file. E [30/Dec/2003:06:26:50 -0500] print_job: Unsupported format 'application/octet-stream'! I [30/Dec/2003:06:26:50 -0500] Hint: Do you have the raw file printing rules enabled? I have uncommented the application/octet-stream application/vnd.cups-raw line from the /etc/cups/mime.convs file on the server to no avail. The XP box sees the print share as well as all the other "shares" configured. What is the magic trick to print from the XP box? I've seen a similar problem reported on the list recently but my problem "seems" different at least according to the messages above. Thanks in advance Regards Mark

4 5

K3b stops writing with "Unkown Error 254"
by James Mohr 07 Jan '04

07 Jan '04

Hi All! I am using the default version of k3b which came with Suse 9.0 (0.10). I have tried writing as both root and my normal user, with various speeds, but it always dies at about 8%. Someone posted a bug reported on kde.org with basically the same problem although they say that they cannot write at all. This was reported about a month ago and it is still listed as "unconfirmed". I am using an AOPEN CD-RW CRW5224 and thing most annoying thing is that it did work once. Obviously something happened, but I cannot figure out what it was. Any help would be greatly appreaciated. Regards, jimmo the error was: _______________________________________ ... Cdrecord returned an unknown error! (code 254) Unkown Error 254 Please send me an email with the last output. System ----------------------- K3b Version: 0.10 KDE Version: 3.1.4 QT Version: 3.2.1 cdrecord ----------------------- scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.25 /usr/bin/cdrecord: Warning: using inofficial libscg transport code version (okir(a)suse.de-scsi-linux-sg.c-1.75-resmgr-patch '@(#)scsi-linux-sg.c 1.75 02/10/21 Copyright 1997 J. Schilling'). SCSI buffer size: 64512 Cdrecord-Clone 2.01a18-dvd (i686-suse-linux) Copyright (C) 1995-2003 Jörg Schilling Note: This version is an unofficial (modified) version with DVD support Note: and therefore may have bugs that are not present in the original. Note: Please send bug reports or support requests to <warly(a)mandrakesoft.com>. Note: The author of cdrecord is not to be bothered with problems in this version. TOC Type: 1 = CD-ROM Using libscg version 'schily-0.7' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'AOPEN ' Identifikation : 'CD-RW CRW5224 ' Revision : '1.05' Device seems to be: Generic mmc CD-RW. Current: 0x0009 Profile: 0x0008 Profile: 0x0009 (current) Profile: 0x000A Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R Drive buf size : 1359872 = 1328 KB FIFO size : 4194304 = 4096 KB Track 01: data 625 MB Total size: 717 MB (71:07.80) = 320085 sectors Lout start: 718 MB (71:09/60) = 320085 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Is not unrestricted Is not erasable Disk sub type: Medium Type B, low Beta category (B-) (4) ATIP start of lead in: -11933 (97:22/67) ATIP start of lead out: 359849 (79:59/74) Disk type: Short strategy type (Phthalocyanine or similar) Manuf. index: 43 Manufacturer: Acer Media Technology, Inc. Blocks total: 359849 Blocks current: 359849 Blocks remaining: 39764 Forcespeed is OFF. Starting to write CD/DVD at speed 1 in real SAO mode for single session. Last chance to quit, starting real write in 2 seconds. 1 seconds. 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. trackno=0 BURN-Free is OFF. Performing OPC... Sending CUE sheet... Writing pregap for track 1 at -150 Starting new track at sector: 0 Track 01: 0 of 625 MB written. Track 01: 1 of 625 MB written (fifo 100%) [buf 40%] 0.9x. Track 01: 2 of 625 MB written (fifo 87%) [buf 33%] 12.9x. Track 01: 3 of 625 MB written (fifo 98%) [buf 38%] 25.6x. Track 01: 4 of 625 MB written (fifo 100%) [buf 43%] 24.9x. Track 01: 5 of 625 MB written (fifo 98%) [buf 48%] 25.6x. Track 01: 6 of 625 MB written (fifo 100%) [buf 52%] 24.5x. Track 01: 7 of 625 MB written (fifo 96%) [buf 56%] 25.7x. Track 01: 8 of 625 MB written (fifo 96%) [buf 62%] 25.1x. Track 01: 9 of 625 MB written (fifo 98%) [buf 67%] 25.9x. Track 01: 10 of 625 MB written (fifo 96%) [buf 72%] 25.1x. Track 01: 11 of 625 MB written (fifo 98%) [buf 59%] 20.8x. Track 01: 12 of 625 MB written (fifo 98%) [buf 63%] 25.0x. Track 01: 13 of 625 MB written (fifo 98%) [buf 67%] 25.8x. Track 01: 14 of 625 MB written (fifo 100%) [buf 71%] 25.0x. Track 01: 15 of 625 MB written (fifo 98%) [buf 75%] 25.6x. Track 01: 16 of 625 MB written (fifo 98%) [buf 78%] 25.0x. Track 01: 17 of 625 MB written (fifo 100%) [buf 82%] 25.8x. Track 01: 18 of 625 MB written (fifo 100%) [buf 85%] 24.9x. Track 01: 19 of 625 MB written (fifo 96%) [buf 88%] 25.6x. Track 01: 20 of 625 MB written (fifo 98%) [buf 87%] 24.8x. Track 01: 21 of 625 MB written (fifo 98%) [buf 77%] 20.9x. Track 01: 22 of 625 MB written (fifo 98%) [buf 79%] 24.8x. Track 01: 23 of 625 MB written (fifo 96%) [buf 81%] 25.6x. Track 01: 24 of 625 MB written (fifo 100%) [buf 82%] 24.5x. Track 01: 25 of 625 MB written (fifo 95%) [buf 84%] 25.6x. Track 01: 26 of 625 MB written (fifo 100%) [buf 86%] 24.7x. Track 01: 27 of 625 MB written (fifo 98%) [buf 87%] 25.4x. Track 01: 28 of 625 MB written (fifo 98%) [buf 88%] 24.6x. Track 01: 29 of 625 MB written (fifo 98%) [buf 89%] 25.5x. Track 01: 30 of 625 MB written (fifo 98%) [buf 72%] 21.2x. Track 01: 31 of 625 MB written (fifo 100%) [buf 73%] 24.0x. Track 01: 32 of 625 MB written (fifo 100%) [buf 73%] 24.6x. Track 01: 33 of 625 MB written (fifo 98%) [buf 72%] 25.1x. Track 01: 34 of 625 MB written (fifo 100%) [buf 72%] 26.1x. Track 01: 35 of 625 MB written (fifo 100%) [buf 72%] 25.2x. Track 01: 36 of 625 MB written (fifo 96%) [buf 71%] 26.0x. Track 01: 37 of 625 MB written (fifo 96%) [buf 70%] 25.1x. Track 01: 38 of 625 MB written (fifo 98%) [buf 69%] 25.9x. Track 01: 39 of 625 MB written (fifo 100%) [buf 68%] 25.2x. Track 01: 40 of 625 MB written (fifo 93%) [buf 48%] 21.0x. Track 01: 41 of 625 MB written (fifo 98%) [buf 47%] 25.1x. Track 01: 42 of 625 MB written (fifo 98%) [buf 44%] 25.5x. Track 01: 43 of 625 MB written (fifo 96%) [buf 42%] 25.1x. Track 01: 44 of 625 MB written (fifo 98%) [buf 39%] 25.7x. Track 01: 45 of 625 MB written (fifo 98%) [buf 37%] 25.0x. Track 01: 46 of 625 MB written (fifo 95%) [buf 34%] 25.8x. Track 01: 47 of 625 MB written (fifo 100%) [buf 32%] 25.0x. Track 01: 48 of 625 MB written (fifo 98%) [buf 29%] 25.7x. Track 01: 49 of 625 MB written (fifo 100%) [buf 19%] 23.3x. Track 01: 50 of 625 MB written (fifo 96%) [buf 2%] 21.8x. /usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 64 DF 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 06 00 00 00 00 0C 00 00 00 00 29 00 00 00 Sense Key: 0x6 Unit Attention, Segment 0 Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 39.887s timeout 200s /usr/bin/cdrecord: A write error occured. /usr/bin/cdrecord: Please properly read the error message above. write track data: error after 52885504 bytes Writing time: 80.158s Average write speed 59.2x. Min drive buffer fill was 2% Total of 1 possible drive buffer underruns predicted. Fixating... Fixating time: 0.003s /usr/bin/cdrecord: fifo had 897 puts and 834 gets. /usr/bin/cdrecord: fifo was 0 times empty and 257 times full, min fill was 84%. cdrecord comand: ----------------------- /usr/bin/cdrecord -v gracetime=2 dev=0,0,0 speed=1 -dao -eject -data -tsize=320085s - mkisofs ----------------------- 320085 0.16% done, estimate finish Fri Dec 26 21:31:06 2003 0.31% done, estimate finish Fri Dec 26 21:31:06 2003 0.47% done, estimate finish Fri Dec 26 21:31:06 2003 0.63% done, estimate finish Fri Dec 26 21:31:06 2003 0.78% done, estimate finish Fri Dec 26 22:17:53 2003 0.94% done, estimate finish Fri Dec 26 22:13:43 2003 1.10% done, estimate finish Fri Dec 26 22:07:33 2003 1.25% done, estimate finish Fri Dec 26 22:03:03 2003 1.41% done, estimate finish Fri Dec 26 21:59:31 2003 1.57% done, estimate finish Fri Dec 26 21:57:41 2003 1.72% done, estimate finish Fri Dec 26 21:55:18 2003 1.88% done, estimate finish Fri Dec 26 21:53:18 2003 2.03% done, estimate finish Fri Dec 26 21:52:25 2003 2.19% done, estimate finish Fri Dec 26 21:50:52 2003 2.34% done, estimate finish Fri Dec 26 21:49:35 2003 2.50% done, estimate finish Fri Dec 26 21:48:24 2003 2.66% done, estimate finish Fri Dec 26 21:48:01 2003 2.81% done, estimate finish Fri Dec 26 21:47:05 2003 2.97% done, estimate finish Fri Dec 26 21:46:15 2003 3.13% done, estimate finish Fri Dec 26 21:46:00 2003 3.28% done, estimate finish Fri Dec 26 21:45:18 2003 3.44% done, estimate finish Fri Dec 26 21:44:40 2003 3.59% done, estimate finish Fri Dec 26 21:44:04 2003 3.75% done, estimate finish Fri Dec 26 21:43:59 2003 3.91% done, estimate finish Fri Dec 26 21:43:27 2003 4.06% done, estimate finish Fri Dec 26 21:42:59 2003 4.22% done, estimate finish Fri Dec 26 21:42:33 2003 4.37% done, estimate finish Fri Dec 26 21:42:31 2003 4.53% done, estimate finish Fri Dec 26 21:42:07 2003 4.69% done, estimate finish Fri Dec 26 21:41:45 2003 4.85% done, estimate finish Fri Dec 26 21:41:45 2003 5.00% done, estimate finish Fri Dec 26 21:41:25 2003 5.16% done, estimate finish Fri Dec 26 21:41:07 2003 5.32% done, estimate finish Fri Dec 26 21:40:49 2003 5.47% done, estimate finish Fri Dec 26 21:40:50 2003 5.63% done, estimate finish Fri Dec 26 21:40:34 2003 5.78% done, estimate finish Fri Dec 26 21:40:19 2003 5.94% done, estimate finish Fri Dec 26 21:40:21 2003 6.09% done, estimate finish Fri Dec 26 21:40:07 2003 6.25% done, estimate finish Fri Dec 26 21:39:54 2003 6.41% done, estimate finish Fri Dec 26 21:39:40 2003 6.56% done, estimate finish Fri Dec 26 21:39:43 2003 6.72% done, estimate finish Fri Dec 26 21:39:32 2003 6.87% done, estimate finish Fri Dec 26 21:39:20 2003 7.03% done, estimate finish Fri Dec 26 21:39:23 2003 7.19% done, estimate finish Fri Dec 26 21:39:12 2003 7.34% done, estimate finish Fri Dec 26 21:39:02 2003 7.50% done, estimate finish Fri Dec 26 21:38:52 2003 7.66% done, estimate finish Fri Dec 26 21:38:56 2003 7.81% done, estimate finish Fri Dec 26 21:38:46 2003 7.97% done, estimate finish Fri Dec 26 21:38:37 2003 8.13% done, estimate finish Fri Dec 26 21:38:28 2003 8.28% done, estimate finish Fri Dec 26 21:38:32 2003 8.44% done, estimate finish Fri Dec 26 21:38:24 2003 8.59% done, estimate finish Fri Dec 26 21:38:16 2003 mkisofs comand: ----------------------- /usr/bin/mkisofs -gui -graft-points -V Young Net B1 -volset -A K3B THE CD KREATOR VERSION 0.10 (C) 2003 SEBASTIAN TRUEG AND THE K3B TEAM -P -p K3b - Version 0.10 -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-root/ k3bhMe6Ra.tmp -r -hide-list /tmp/kde-root/k3bzuoZob.tmp -l -iso-level 2 -path-list /tmp/kde-root/k3bJSnrUb.tmp

11 23

wlan0 DSL HELP
by Mailing 06 Jan '04

06 Jan '04

Hi, I discovered that Suse named wireless NIC wlanX instead ethX. This it's ok but the problem is that DSL YAST module doesn't give me the possibility to choose it. With Any other distribution is possible to use wireless PCMCIA to use DSL connections. Any ideas? Thanks Andrea

2 5

Font Question - where to change
by Charles Love 06 Jan '04

06 Jan '04

A while ago I was trying to get my ATI Card working.. And for what ever reason what ever I did, didnt quite work. My laptop has a default res of 1280X1600 and My fonts always looked big. The other day i was doing something and a crash happened. I then lost my lower taskbar, when I rebooted all my fonts were tiny.. I think this is how it should look like at 1280X1600 res. But now I am used to the large fonts. Where can I go to change it? I went through the right click of the desktop and went through the configure desktop menu and it seems to make my desktop icons nice but my apps like Mozilla, and Evolution are still small.. where should i be looking for these?? Thanks! Charles

4 6