October 2008 - openSUSE Users - openSUSE Mailing Lists

Re: [opensuse] screwy time
by Bob S 22 Oct '08

22 Oct '08

On Tuesday 21 October 2008 03:06:33 am Ingolf Steinbach wrote: > Hi. > > 2008/10/21 Bob S <911(a)sanctum.com>: > > Every time I reboot my computrer it loses 4 hours exactly. (I shut down > > every night and restart the folowing day) I can set the time exactly > > using an NTP server Running 10.3 64 bit and KDE3. > > [...] > > > Anyone, any ideas on what could be happening here? > > Your mail header reports > > > Date: Tue, 21 Oct 2008 01:46:08 -0400 > > (note the -0400). Maybe it is a problem with the configuration of your > hardware clock (whether it runs at local time or at UTC). Do you boot > "that other OS" in between.? > Hi Ingolf, Well it looks like the system clock runs on local time and it also looks like the ntp server is setting local time. I did this a little after midnight. (UTC -4)(Eastern Daylight Time) Easystreet:/ # ntpdate clock.isc.org 22 Oct 00:26:06 ntpdate[4625]: adjust time server 204.152.184.72 offset -0.123777 sec Easystreet:/ # hwclock --show ; date ; date -u Wed 22 Oct 2008 12:26:17 AM EDT -0.789944 seconds Wed Oct 22 00:26:16 EDT 2008 Wed Oct 22 04:26:16 UTC 2008 Easystreet:/ # hwclock --systohc Easystreet:/ # rm /etc/adjtime Easystreet:/ # I do have "that other OS" on a small drive but haven't booted it in over a year. And, I rebooted into the bios and the time was correct and then let it continue to boot into SuSE and lost four hours. Then rebooted into the bios and it showed the lost 4 hours, then let it finish booting into Suse and lost another four hours. Something in the start-up script? Bob S -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

2 1

[opensuse] IRQ conflect
by Mike Adolf 22 Oct '08

22 Oct '08

I am having trobble getting my tuner card to work. I noticed the following error in dmesg. cx88[0]/1: IRQ loop detected, disabling interrupts How do I see what the IRQ setting are and how do I change them? I'm using SuSe 11. Mike -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

1 0

Re: [opensuse] Getting Rid of postfix and exim on my laptop
by Carlos E. R. 22 Oct '08

22 Oct '08

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Content-ID: <alpine.LSU.2.00.0810222329580.23941(a)nimrodel.valinor> El 2008-10-22 a las 16:21 -0400, Anton Aylward escribió: Please, reply on list. > Carlos E. R. said the following on 10/22/2008 03:11 PM: >> Why do you think you don't need it? > > I've just converted from Mandriva and I didn't need it there. > I didn't need it because I have a mail server on the network. > Thunderbird connects to the mail server via IMAP and SMTP, so there is > no need for SMTP services on my laptop. For that use you are correct, you do not need it. But is is not the only use. > Cristian Rodríguez said the following on 10/22/2008 03:19 PM: >> Ruben Safir escribió: >>> I want to get rid of postfix and exim >> >> ... >> >> I do not need a mail server on my latop, but I do need cron. >> >> cron requires smtp_server capability. > > I can see how cron might need smtp to deliver mail, but what if cron is > not installed? What for? Cron has to be installed, there are system services that depend on it - at least on an openSUSE system it is needed. > Then again cron might only be delivering locally - this used to be done > with mailx - so why is smtp needed. I suppose it uses the sendmail command to send, not mailx. And I understand that mailx uses the smtp server to send, anyway. > In reality, shouldn't cron deliver its error messages via syslog? No, it can't, or you might find thousands of syslog entries coming from cron output. Would you prefer that? > I really hate all these dependencies that arise out of lack of > consideration of alternatives. Then perhaps you should design a distro with those premises >:-) - -- Saludos Carlos E.R. -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.9 (GNU/Linux) iEYEARECAAYFAkj/nb8ACgkQtTMYHG2NR9UHHwCfQZ0Yik34lAAqVybwB/VbUBhP U2EAn3L6YJOy/b0pzawPnxFimbRiEb9n =SFzk -----END PGP SIGNATURE-----

1 0

[opensuse] Remote upgrade problem
by Matthew Stringer 22 Oct '08

22 Oct '08

Hi, I've a lot of servers in a remote DC that I've no physical access to, they're running 10.2. I wish to upgrade them to 11.0 remotely, but for some reason it's not working correctly. Firstly I've been downloading the install kernel and initrd: cd /boot wget -O vmlinuz.install ftp://ftp.opensuse.org/pub/opensuse/distribution/11.0/repo/oss/boot/i386/lo… wget -O initrd.install ftp://ftp.opensuse.org/pub/opensuse/distribution/11.0/repo/oss/boot/i386/lo… Then adding an entry into Grub: title Boot -- SUSE LINUX 11.0 root (hd0,1) kernel /boot/vmlinuz.install noapic usessh=1 sshpassword="12345678" install=ftp://ftp.opensuse.org/pub/opensuse/distribution/11.0/repo/oss hostip=xx.xx.xx.xx netmask=255.255.255.0 gateway=xx.xx.xx.xx nameserver=xx.xx.xx.xx initrd /boot/initrd.install then using grubonce 1 to make it use that entry on next boot. Now the machine boots up and starts the network, I can ping it. But it never starts the installation program, so I'm assuming that it's because for whatever reason it's unable to download it. I'm doing this blind as I've no access other than SSH and there's no-one to plug in a monitor/KVM so I can see the output. As all the details are correct and I can use wget on the URL and download the files using the DNS server specified I'm thinking it's possibly because it's trying to use the wrong NIC. The machine has an internal card (eth0) and a PCI gigabit one (eth1), I'm thinking that as I'm using the latter, grub is trying to use the other despite there not being a connection to it (I know it start the network with the correct device as I can ping it, but I've run out of other ideas). I've done this remote upgrade method loads of times before without problem, the only thing I can see different here is the 2NIC's. If this is plausible is there a command to specify which device it should use? Cheers Matthew -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

2 1

[opensuse] Re: [opensuse-factory] we have a beta3 - but why the different content types in the directories?
by Rafael E. Herrera 22 Oct '08

22 Oct '08

Ken Schneider wrote: > When I go to http://download.opensuse.org/distribution/11.1-Beta3/iso/ it > shows the B2-B3 x86 delta as being 488M, but the actual downloaded file is > much smaller. What gives with that? openSUSE-11.1-Beta2_Beta3-DVD-i386.delta.iso is reported as 488M, but the size of the downloaded file is 220M in some mirrors. The md5sum of the smaller file does not match the md5sum as published in the web site. The file in ftp5.gwdg.de seems to have the right size and it matches the checksum. -- Rafael E. Herrera -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

1 0

[opensuse] SonyEricsson P1i anyone ?
by Philippe Andersson 22 Oct '08

22 Oct '08

Hello, Anyone here uses a SonyEricsson P1i and cares to comment on its Linux compatibility ? TIA Ph. A. -- *Philippe Andersson* Unix System Administrator IBA Particle Therapy | Tel: +32-10-475.983 Fax: +32-10-487.707 eMail: pan(a)iba-group.com <http://www.iba-worldwide.com> The contents of this e-mail message and any attachments are intended solely for the recipient (s) named above. This communication is intended to be and to remain confidential and may be protected by intellectual property rights. Any use of the information contained herein (including but not limited to, total or partial reproduction, communication or distribution of any form) by persons other than the designated recipient(s) is prohibited. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system. E-mail transmission cannot be guaranteed to be secure or error-free. Ion Beam Applications does not accept liability for any such errors. Thank you for your cooperation.

1 0

[opensuse] HPLIP and ink status
by Duaine & Laura Hechler 22 Oct '08

22 Oct '08

I have noticed that HPLIP (HP Device Manager) does not show the status of the ink levels if the cartridges have been refilled. Is this normal ? -- Duaine Hechler Piano, Player Piano, Pump Organ Tuning, Servicing & Rebuilding Reed Organ Society Member Florissant, MO 63034 (314) 838-5587 dahechler(a)charter.net www.hechlerpianoandorgan.com -- Home & Business user of Linux - 10 years -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

6 13

[opensuse] Automated installation of VMware Workstation 6.5
by Bernd Nies 22 Oct '08

22 Oct '08

Hi, With versions of VMware Workstations up to 6.0.5 it was possible to automate the installation by using a prepared /etc/vmware/locations and running vmware-config.pl --default EULA_AGREED=yes With version 6.5 this is no longer possible because the vmware-config.pl does no longer exist and the installer wants confirmation for EULA agreement. The attached shell script does an automated installation with predefined subnets vor vmnet1 and vmnet8. It is tested on openSUSE 11.0. Hope this helps someone not to waste a whole day for this. Bye Bernd ==CUT== #!/bin/bash VMBUNDLE="/var/adm/autoinstall/files/VMware-Workstation-6.5.0-118166.i386.bundle" # Hostonly network (interface vmnet1) VMNET1_SUBNET="172.16.253.0" VMNET1_NETMASK="255.255.255.0" VMNET1_BROADCAST="172.16.253.255" VMNET1_IP="172.16.253.1" VMNET1_DHCPRANGE="172.16.253.129 172.16.253.254" # NAT network (interface vmnet8) VMNET8_SUBNET="172.16.254.0" VMNET8_NETMASK="255.255.255.0" VMNET8_BROADCAST="172.16.254.255" VMNET8_IP="172.16.254.1" VMNET8_GATEWAY="172.16.254.2" VMNET8_DHCPRANGE="172.16.254.129 172.16.254.254" # Uninstall previous VMware Workstation 6.5 if [ -x /usr/bin/vmware-uninstall ]; then TERM=dumb /usr/bin/vmware-uninstall --console rm -rf /etc/vmware fi expect <<==EOF== set env(TERM) dumb set timeout 30 spawn $VMBUNDLE --console --required expect { -re ".*Press enter to proceed.*" {send "\r"; exp_continue} -re ".*--More--.*" {send "q"; exp_continue} -re ".*Do you agree.*yes/no.*" {send "yes\r"; exp_continue} -re ".*$optional$:.*" {send "\r"; exp_continue} timeout {exp_continue} eof } ==EOF== /etc/init.d/vmware stop # Backup old config cp -f /etc/vmware/networking /etc/vmware/networking.org cp -f /etc/vmware/vmnet1/dhcpd/dhcpd.conf /etc/vmware/vmnet1/dhcpd/dhcpd.conf.org cp -f /etc/vmware/vmnet8/dhcpd/dhcpd.conf /etc/vmware/vmnet8/dhcpd/dhcpd.conf.org cp -f /etc/vmware/vmnet8/nat/nat.conf /etc/vmware/vmnet8/nat/nat.conf.org sed -re " s/VNET_1_HOSTONLY_NETMASK +[0-9\.]+/VNET_1_HOSTONLY_NETMASK ${VMNET1_NETMASK}/; s/VNET_1_HOSTONLY_SUBNET +[0-9\.]+/VNET_1_HOSTONLY_SUBNET ${VMNET1_SUBNET}/; s/VNET_8_HOSTONLY_NETMASK +[0-9\.]+/VNET_8_HOSTONLY_NETMASK ${VMNET8_NETMASK}/; s/VNET_8_HOSTONLY_SUBNET +[0-9\.]+/VNET_8_HOSTONLY_SUBNET ${VMNET8_SUBNET}/; " /etc/vmware/networking.org > /etc/vmware/networking sed -re " s/subnet +[0-9\.]+/subnet ${VMNET1_SUBNET}/; s/netmask +[0-9\.]+/netmask ${VMNET1_NETMASK}/; s/range +[0-9\.]+ +[0-9\.]+/range ${VMNET1_DHCPRANGE}/; s/broadcast-address +[0-9\.]+/broadcast-address ${VMNET1_BROADCAST}/; s/domain-name-servers +[0-9\.]+/domain-name-servers ${VMNET1_IP}/; " /etc/vmware/vmnet1/dhcpd/dhcpd.conf.org > /etc/vmware/vmnet1/dhcpd/dhcpd.conf sed -re " s/subnet +[0-9\.]+/subnet ${VMNET8_SUBNET}/; s/netmask +[0-9\.]+/netmask ${VMNET8_NETMASK}/; s/range +[0-9\.]+ +[0-9\.]+/range ${VMNET8_DHCPRANGE}/; s/broadcast-address +[0-9\.]+/broadcast-address ${VMNET8_BROADCAST}/; s/domain-name-servers +[0-9\.]+/domain-name-servers ${VMNET8_GATEWAY}/; s/routers +[0-9\.]+/routers ${VMNET8_GATEWAY}/; " /etc/vmware/vmnet8/dhcpd/dhcpd.conf.org > /etc/vmware/vmnet8/dhcpd/dhcpd.conf sed -re " s/ip += +[0-9\.]+/ip = ${VMNET8_GATEWAY}/; s/netmask += +[0-9\.]+/netmask = ${VMNET8_NETMASK}/; " /etc/vmware/vmnet8/nat/nat.conf.org > /etc/vmware/vmnet8/nat/nat.conf chown root:root /etc/vmware/networking chown root:root /etc/vmware/vmnet1/dhcpd/dhcpd.conf chown root:root /etc/vmware/vmnet8/dhcpd/dhcpd.conf chown root:root /etc/vmware/vmnet8/nat/nat.conf chmod 600 /etc/vmware/networking chmod 665 /etc/vmware/vmnet1/dhcpd/dhcpd.conf chmod 665 /etc/vmware/vmnet8/dhcpd/dhcpd.conf chmod 665 /etc/vmware/vmnet8/nat/nat.conf /etc/init.d/vmware start ==CUT== -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

1 0

[opensuse] Mac HD in x86 system?
by Felix Miata 22 Oct '08

22 Oct '08

fdisk -l tells me no valid partition table. I took the HD out of a Mac that won't boot to desktop, thinking the problem may be an overstuffed disk that simply needs some disk cleanup, and mounted it as sole device on the #2 PATA controller as /dev/sdc. Don't Mac disks use a GPT, similar to recent Vista systems? Is this doable somehow in x86 11.0 or Factory? -- "Everyone should be quick to listen, slow to speak, and slow to become angry." James 1:19 NIV Team OS/2 ** Reg. Linux User #211409 Felix Miata *** http://fm.no-ip.com/ -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

3 5

[opensuse] Real-world Transfered Speed over 100tx Network
by David C. Rankin 22 Oct '08

22 Oct '08

Listmates, What are the real-world transfer speeds you are seeing with rsync SuSEbox-to-SuSEbox over a 100TX network? As files get larger, the backup/transfer times keep rising. I am seeing transfer rates for gigabyte size files of 11.04 MB/s over the network. A comparison to drive-to-drive transfers within the same 10.3 box are about 28 MB/s. I wouldn't expect box-to-box transfers to be the same as drive-to-drive transfers, but losing 60% seems large. That maybe normal, but I thought I would ask and see what others are seeing. Are there any other tips or tricks to speed things up? -- David C. Rankin, J.D., P.E. Rankin Law Firm, PLLC 510 Ochiltree Street Nacogdoches, Texas 75961 Telephone: (936) 715-9333 Facsimile: (936) 715-9339 www.rankinlawfirm.com -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse+help(a)opensuse.org

4 3