November 2000 - openSUSE Users - openSUSE Mailing Lists

Re: [SLE] ISDN help
by juergen.braukmann＠ruhr-west.de 27 Nov '00

27 Nov '00

From: juergen.braukmann(a)ruhr-west.de Message-ID: <3A21F683.76171307(a)ruhr-west.de> Date: Mon, 27 Nov 2000 06:52:03 +0100 Subject: Re: [SLE] ISDN help Greg Farrell wrote: > > >You do *not* need to reinstall. OK, ISDN is configured and causes the > >same crash on reboot, but use the rescue system and turn ISDN off in > >rc.config: I4l_START=no. > How do i get into the rescue system? If i bot from cd i cannt seem to get a > prompt? 1) use the rescue disk. (CD1, directory disks. create it either with rawrite from DOS or "dd if=rescue of=/dev/fd0" from linux 2) boot from CD1. enter "manual" at the lilo prompt. you're in text mode and following instructions, you'll find the rescue system 3) boot into ysat2 and quit. You end up in text mode. Same as above 4) boot drom CD2. This leads into text mode. Juergen > > >With the next reboot, you get another chance for trial and error. ;-)) > >I recomend suse-isdn though... ;-) > Heh thanks. This will save mea bout an hour per test :) > Greg -- =========================================== __ _ Juergen Braukmann juergen.braukmann(a)gmx.de| -o)/ / (_)__ __ ____ __ Tel: 0201-743648 dk4jb(a)db0qs.#nrw.deu.eu | /\\ /__/ / _ \/ // /\ \/ / ===========================================_\_v __/_/_//_/\_,_/ /_/\_\

1 0

RE: [SLE] Balsa, mahogany, kmail...Summing up
by tbutler＠uninetsolutions.com 27 Nov '00

27 Nov '00

From: "Timothy R. Butler" <tbutler(a)uninetsolutions.com> Date: Sun, 26 Nov 2000 22:07:16 -0600 Message-ID: <001201c05827$8772f240$0101a8c0@g4958> Subject: RE: [SLE] Balsa, mahogany, kmail...Summing up Hi Doug > Why would anyone want a virus trap like MS Outlook or Outlook E? KDE kmail > works well, if you can figure out how to set it up. (I am not quite there, I didn't mean I would like to see Kmail becoming a Virus trap. Why is it whenever someone says something good about MS software, it's assumed we must copy all of the problems - and perhaps only the problems? I suggested taking the really nice powerful stuff - not the security flaws. -Tim ----------------------------------------------------------------- Timothy R. Butler Universal Networks Information Tech. Consultant Christian Web Services Since 1996 ICQ #12495932 AIM: Uninettm An Authorized IPSwitch Reseller tbutler(a)uninetsolutions.com http://www.uninetsolutions.com ===================== "Solutions that Work" =====================

1 0

ICP-Vortex 6518RS, SuSE 7.0 install
by julie＠lach.net 27 Nov '00

27 Nov '00

Message-ID: <3A21664A.FBEA1FBC(a)lach.net> Date: Sun, 26 Nov 2000 13:37:48 -0600 From: Julie Dunlop <julie(a)lach.net> Subject: ICP-Vortex 6518RS, SuSE 7.0 install Hello. I have a mess on my hands and I can't figure it out :( I have an Asus P2B-F mb with PIII 800 mhz, 256Meg ram, IDE CDrom, ICP-Vortex controller with a Raid 5 drive configured. The system will *not* boot from the cdrom at all. If I boot from the floppy, it finds the IDE cdrom just fine, I tell it to load the module for the ICP-Vortex controller and it finds that also. I then tell it to install the OS. It load the inital ram disk and then stops end of story!!! If I do the above proceedure without loading the ICP-Vocrtex controller module, Yast runs but the install fails when it cannot find any hard disks. What is the controller doing to the system? Thanks lach

2 1

Final results of compiling experiments in KDE2...
by jerrykreps＠jlkreps.net 27 Nov '00

27 Nov '00

From: Jerry Kreps <jerrykreps(a)jlkreps.net> Date: Sun, 26 Nov 2000 21:24:52 -0600 Message-Id: <00112621245200.22495@JLKreps> Subject: Final results of compiling experiments in KDE2... Well, after installing a pristine Qt-2.2.1 source and compiling it with jpeg, png, gif and mng graphics active...... After removing all traces of KDE1 and KDE2 files and their dependent files, and rebuilding the rpm database.... After installing a pristine KDE2 from the SuSE ftp site...... After setting up QTDIR, KDEDIR, MANPATH and LD_LIBRARY_PATH.... After modifying ld.so.conf and running ldconfg..... Attempts to compile BibleTime-0.31, Quanta and Kemsitry are successful but the programs refuse to run. They all KCrash with essentially the identical error: Here is the output of KCrash...... 0x40dbd019 in __wait4 () from /lib/libc.so.6 #0 0x40dbd019 in __wait4 () from /lib/libc.so.6 #1 0x40e1a718 in __DTOR_END__ () from /lib/libc.so.6 #2 0x40436e20 in KCrash::defaultCrashHandler () from /opt/kde2/lib/libkdecore.so.3 #3 0x40d5a9e8 in __restore () at ../sysdeps/unix/sysv/linux/i386/sigaction.c:127 #4 0x4081e0e7 in read_png_image () from /usr/lib/qt/lib/libqt.so.2 #5 0x407c1fd9 in QImageIO::read () from /usr/lib/qt/lib/libqt.so.2 #6 0x407bff01 in QImage::load () from /usr/lib/qt/lib/libqt.so.2 #7 0x407b9232 in QImage::QImage () from /usr/lib/qt/lib/libqt.so.2 #8 0x40414185 in KIconLoader::loadIcon () from /opt/kde2/lib/libkdecore.so.3 #9 0x40416fc1 in SmallIcon () from /opt/kde2/lib/libkdecore.so.3 #10 0x403e80dd in KApplication::miniIcon () from /opt/kde2/lib/libkdecore.so.3 #11 0x403eecda in KApplication::setTopWidget () from /opt/kde2/lib/libkdecore.so.3 #12 0x4028c312 in KMainWindow::KMainWindow () from /opt/kde2/lib/libkdeui.so.3 #13 0x4028ef7b in KTMainWindow::KTMainWindow () from /opt/kde2/lib/libkdeui.so.3 #14 0x806b6aa in BibleTime::BibleTime () #15 0x806d73e in main () #16 0x40d54a8e in __libc_start_main () at .../sysdeps/generic/libc-start.c:93 I don't know if the problem lies with the Qt libraries or with KDE2 itself. I've never had problems compiling any of these programs under KDE1 with Qt-1.45. I'm coming to the conclusion that folks who write programs specifically for KDE2 should make sure they can compile AND RUN on a pristine box containing only the Qt-2.x they use and KDE2. One problem I've found is that KDE1 uses the /usr/lib/qt-->/usr/lib/qt-1.45 symlink but Qt-2.2.1 expects it to point to /usr/lib/qt-2.2.1. The same symlink cannot point to two different destinations, obviously. During compiling it seems that -lqt was pulling from qt-1.45 and the -I was pulling from qt-2.2.1. Qt-2 expected to see QTDIR=/usr/lib/qt-2.2.1 but it was set to /usr/lib/qt-1.45, and KDEDIR=/opt/kde2, but it was set to /opt/kde. These conflicts are not resolvable without annoying wrappers to preset the env vars. Using wrappers is cobbling nonsense and should not be necessary. These problems were supposedly resolved by settng configure switches, but such switches were not always honored unless you made configure totally blind to qt-1.45 by renaming it and taking it out of ld.so.conf, and pointing symlinks in /usr/lib to the new qt-2.2.1 libs. Another problem is that /usr/lib/libqt.so pointed to qt-1.45 but qt-2.2.1 wanted it to point to its own libs. Using a symlink of /usr/lib/qt2 wasn't a big help because you had to do a lot of manual changing of makefiles or use autoconf or something. The INSTALL instructions always assume that a simple ./configure would perform all that needed to be done. There could be problems with KDE2's libkdecore.so.3 file, which is central to all execution failures. <p>To summerize. I'm setting here with a pristine qt-2.2.1 system, which compiles without a single error or warning, containing the best KDE2 implementation SuSE offers from their ftp site. Normal procedures of creating dynamically linked executables results in a binary that crashes. Installing bibletime-.31 from an rpm made for a SuSE 6.4 system produced the same KCrash error message. An annoying side problem was that the person who created the bibletime-.31 rpm included a library, libfam, which is so rare it is found on only one site. fam (file access monitor) is supposed to report back when a file is accessed. But, the amazing thing is that to make fam work by a kernel interrupt and not be polling, the kernel is supposed to be modifed with a patch. To make matters worse, the patch represents the coder's first foray into Linux kernel coding. I guess someone always has to start some where, even for writing kernel code BUT, writing a patch to the kernel that does not get filtered through the kernel team where very experienced eyeballs can look it over is dangerous. I refused to add that patch to make fam work faster. When KCrash resulted in the same error as the compiled tar file I removed fam from my system. <opinion> KDE2, based on Qt-2.x has been released and is now official. App writers are converting as fast as possible. The sooner everyone cuts loose of KDE1 and switched to KDE2 the better. Creating apps that require both KDE1 (Qt-1.x) and KDE2 (Qt-2.x) to be installed is a disservice to the community, fosters bloat, confusion and chaos. In choosing between rpm or tar files for installation of source, I've come to appreciate the tar file. While rpms may be good for installing static programs (sans source), using an rpm to deposit a tar, which then has to be detared, is a waste. The sequence ./configure, make, make install and, if needed, make uninstall, is very easy to do. What is needed is a GUI dialog app which allows the setting of switches/paths that are available, and buttons that configure, make,make install or uninstall, and executing the app after the process is complete. If the app crashes then an text file containing particulars of the crash and the address of the programmer could be prepared for later mailing. Then, all the user would have to do is check radio buttons to set the graphics, etc., a listbox for the installation directory (prefilled with the recommended one), and click the buttons as needed. If certain tasks need to be done as root their controls would not be active unless the user is root. Since YaST is going graphical too, such a 3rd party program installation app would be a nice complimentary addition. </opinion> JLK -- Scientific theories, according to Sir Karl Popper, can be "falsified," or proven wrong, by experiment. Unscientific theories -Marxist dialectical history and Freudian psychology were Popper's favorites-are formed in such a way that they cannot be falsified by data.

1 0

xmms
by landie＠concentric.net 27 Nov '00

27 Nov '00

Date: Sun, 26 Nov 2000 21:37:38 -0500 From: Landy Roman <landie(a)concentric.net> Message-ID: <20001126213738.A4108(a)concentric.net> Subject: xmms i can find the dev-pack for xmms can some one point me to it -- Rolando Roman SuSe 7.0 Linux virtuoso 2.2.16 #1 Wed Aug 2 20:22:26 GMT 2000 i586 unknown

1 1

SuSE 7.0 on iMAC's
by cwaiken＠telerama.com 27 Nov '00

27 Nov '00

Date: Fri, 24 Nov 2000 23:31:14 -0500 (EST) From: "Christopher W. Aiken" <cwaiken(a)telerama.com> Message-ID: <Pine.LNX.4.21.0011242327260.1691-100000(a)darkstar.local> Subject: SuSE 7.0 on iMAC's Has anyone installed/used SuSE Linux on the new colored iMAC's that seem to be poping up everywhere? Are the iMAC's worth a looksie?? A lot less of the spaghetie wireing :-) -- Christopher W. Aiken, Scenery Hill, Pa, USA chris at cwaiken dot com, www.cwaiken.com Current O/S: SuSE 7.0 Professional Linux

3 2

Music Match (OT)
by tb64710＠ltec.net 27 Nov '00

27 Nov '00

From: Thomas Bishop <tb64710(a)ltec.net> Date: Sun, 26 Nov 2000 19:45:34 -0600 Message-Id: <00112619590700.03549@linuxbox> Subject: Music Match (OT) OK, SuSE'rs, anyone gotten Music Match to work? Plays files on my hard drives, but won't stat my cdrom. I have only a passing acquaintance w/Wine, but the path in wine.ini (wine.conf) is : [Drive G] Path=/mnt/cdrom Type=cdrom Label=CD-Rom Device=/dev/cdrom Looks right to me??? Ideas?? Thankyou. -- TRBishop tb64710(a)ltec.net RLU#12043 SuSE 7.0Pro

2 1

SoundBlaster PCI 128 under SuSE 7.0 ?
by deem＠wdm.com 27 Nov '00

27 Nov '00

From: "W.D.McKinney" <deem(a)wdm.com> Message-Id: <200011241954.eAOJsfe01824(a)wdm.com> Date: Fri, 24 Nov 2000 10:54:41 -0900 (AKST) Subject: SoundBlaster PCI 128 under SuSE 7.0 ? It's the OEM SoundBalster PCI 128. Just a quick check before I buy one these, does the 7.0 install pick these up and running OK ? Nothing in the last few months on the suse-linux-e mail list. /Dee

4 3

Re: [SLE] SuSE 7.0 packages (including avr-gcc)
by bbcat＠linuxstart.com 27 Nov '00

27 Nov '00

Date: Sun, 26 Nov 2000 20:49:10 -0500 Message-Id: <200011270149.eAR1nAt17641(a)tbird.iworld.com> From: Michel Catudal <bbcat(a)linuxstart.com> Subject: Re: [SLE] SuSE 7.0 packages (including avr-gcc) Ed Harrison <edtman(a)ithink.net> wrote: > >> One is on NBCi >> http://members.nbci.com/bbcat_rpm/index.html > >That is one cute penquin. How do I get him to dance on my web page. > This is just a gif file. Do a save image as I got that from the SuSE default webpage on a SuSE 7.0 install. Vous en avez plein l'casse du plantage de Ti-Mou? alors il est temps d'essayer Linux http://www.netonecom.net/~bbcat ---------------------- Do you do Linux? :) Get your FREE @linuxstart.com email address at: http://www.linuxstart.com

1 0

sendmail: MX-problem 7.0
by dan＠younics 27 Nov '00

27 Nov '00

Message-ID: <003d01c03f9f$5c3067c0$bd0230d9@lala> From: "dan@younics" <suse(a)dertext.de> Date: Fri, 27 Oct 2000 00:36:32 +0200 Subject: sendmail: MX-problem 7.0 hello, I have upgraded from 8.8 to 8.9.3 and I find my mailertable setup on MX20 that routes everything back to MX10 not working. "550 Relaying denied..." This is the setup: (sample-domain): Nameservice: db.domain.de MX 10 mail.domain.com. MX 20 mail.MYHOST.com. on mail.MYHOST.com /etc/mail/mailertable: domain.com smtp:[mail.domain.com] .domain.com smtp:[mail.domain.com] traight from the book....it seems. I even tried changinig the official hostname to exactly match the MX pointer, no avail. This just drives me round the pole. any ideas ? tia dan

2 1