Is there any option to override the wrong (EDID ?) data for panel size given
by that display so that I can use the 1600x1200 resolution with the nv
driver :
[...]
(II) NV(0): I2C bus "DDC" initialized.
(II) NV(0): Probing for analog device on output A...
(--) NV(0): ...found one
(II) NV(0): Probing for analog device on output B...
(--) NV(0): ...can't find one
(II) NV(0): Probing for EDID on I2C bus A...
(II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) NV(0): I2C device "DDC:ddc2" removed.
(II) NV(0): ... none found
(II) NV(0): Probing for EDID on I2C bus B...
(II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) NV(0): I2C device "DDC:ddc2" removed.
(--) NV(0): DDC detected a DFP:
(II) NV(0): Manufacturer: IME Model: 5653 Serial#: 808465204
(II) NV(0): Year: 2002 Week: 45
(II) NV(0): EDID Version: 1.3
(II) NV(0): Digital Display Input
(II) NV(0): DFP 1.x compatible TMDS
(II) NV(0): Max H-Image Size [cm]: horiz.: 41 vert.: 31
(II) NV(0): Gamma: 1.00
(II) NV(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) NV(0): First detailed timing is preferred mode
(II) NV(0): redX: 0.647 redY: 0.346 greenX: 0.298 greenY: 0.591
(II) NV(0): blueX: 0.150 blueY: 0.118 whiteX: 0.313 whiteY: 0.329
(II) NV(0): Supported VESA Video Modes:
(II) NV(0): 720x400@70Hz
(II) NV(0): 640x480@60Hz
(II) NV(0): 640x480@67Hz
(II) NV(0): 640x480@72Hz
(II) NV(0): 640x480@75Hz
(II) NV(0): 800x600@56Hz
(II) NV(0): 800x600@60Hz
(II) NV(0): 800x600@72Hz
(II) NV(0): 800x600@75Hz
(II) NV(0): 832x624@75Hz
(II) NV(0): 1024x768@60Hz
(II) NV(0): 1024x768@70Hz
(II) NV(0): 1024x768@75Hz
(II) NV(0): 1280x1024@75Hz
(II) NV(0): Manufacturer's mask: 0
(II) NV(0): Supported Future Video Modes:
(II) NV(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) NV(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
(II) NV(0): #2: hsize: 640 vsize 480 refresh: 85 vid: 22833
(II) NV(0): #3: hsize: 800 vsize 600 refresh: 85 vid: 22853
(II) NV(0): #4: hsize: 1024 vsize 768 refresh: 85 vid: 22881
(II) NV(0): #5: hsize: 1280 vsize 1024 refresh: 85 vid: 39297
(II) NV(0): Supported additional Video Mode:
(II) NV(0): clock: 162.0 MHz Image Size: 408 x 306 mm
(II) NV(0): h_active: 1600 h_sync: 1600 h_sync_end 1792 h_blank_end 2160
h_border: 0
(II) NV(0): v_active: 1200 v_sync: 1200 v_sync_end 1203 v_blanking: 1250
v_border: 0
(II) NV(0): Ranges: V min: 56 V max: 85 Hz, H min: 31 H max: 92 kHz,
PixClock max 170 MHz
(II) NV(0): Serial No: ALFFSA3300034
(II) NV(0): Monitor name: L20CM
(II) NV(0): EDID (in hex):
(II) NV(0): 00ffffffffffff0025a5535634333030
(II) NV(0): 2d0c010381291fffeae595a5584c9726
(II) NV(0): 1e5054bfef008180a940315945596159
(II) NV(0): 819901010101483f403062b0324000c0
(II) NV(0): 030098321100001e000000fd0038551f
(II) NV(0): 5c11000a202020202020000000ff0041
(II) NV(0): 4c4646534133333030303334000000fc
(II) NV(0): 004c3230434d0a2020202020202000bf
(--) NV(0): CRTC 0 is currently programmed for DFP
(II) NV(0): Using DFP on CRTC 0
(--) NV(0): Panel size is 1280 x 1024
(II) NV(0): Using hsync ranges from config file
(II) NV(0): Using vrefresh ranges from config file
(II) NV(0): Printing DDC gathered Modelines:
(II) NV(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
+hsync +vsync
(II) NV(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
+hsync +vsync
(II) NV(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484
500 -hsync -vsync
(II) NV(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491
520 -hsync -vsync
(II) NV(0): Modeline "640x480" 30.24 640 704 768 864 480 483 486
525 -hsync -vsync
(II) NV(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492
525 -hsync -vsync
(II) NV(0): Modeline "720x400" 28.32 720 738 846 900 400 412 414
449 -hsync +vsync
(II) NV(0): Modeline "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028
1066 +hsync +vsync
(II) NV(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800
+hsync +vsync
(II) NV(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777
806 -hsync -vsync
(II) NV(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777
806 -hsync -vsync
(II) NV(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628
667 -hsync -vsync
(II) NV(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625
+hsync +vsync
(II) NV(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666
+hsync +vsync
(II) NV(0): Modeline "1280x1024" 109.00 1280 1368 1496 1712 1024 1027 1034
1063 -hsync +vsync
(II) NV(0): Modeline "1600x1200" 161.00 1600 1712 1880 2160 1200 1203 1207
1245 -hsync +vsync
(II) NV(0): Modeline "640x480" 35.00 640 664 728 816 480 483 487
507 -hsync +vsync
(II) NV(0): Modeline "800x600" 56.75 800 848 928 1056 600 603 607
633 -hsync +vsync
(II) NV(0): Modeline "1024x768" 94.50 1024 1096 1200 1376 768 771 775
809 -hsync +vsync
(II) NV(0): Modeline "1280x1024" 159.50 1280 1376 1512 1744 1024 1027 1034
1078 -hsync +vsync
(II) NV(0): Modeline "1600x1200" 162.00 1600 1600 1792 2160 1200 1200 1203
1250 +hsync +vsync
(II) NV(0): Panel is TMDS
(--) NV(0): VideoRAM: 262144 kBytes
(==) NV(0): Using gamma correction (1.0, 1.0, 1.0)
(II) NV(0): Monitor[0]: Using hsync range of 30.00-92.00 kHz
(II) NV(0): Monitor[0]: Using vrefresh range of 43.00-85.00 Hz
(II) NV(0): Clock range: 12.00 to 400.00 MHz
(II) NV(0): Not using mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "320x175" (bad mode
clock/interlace/doublescan)
[...]
--
To unsubscribe, e-mail: opensuse-xorg+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-xorg+help(a)opensuse.org
> On Mon, Apr 21, 2008 at 01:17:28PM +0200, alibeck(a)berlinet.de wrote:
>> Hi List,
>>
>> I can manage it to get the dual head mode running correctly.
>>
>> I have an IBM Lenovo T60 laptop, and OpenSuSE 10.3 installed on it, with
>> a
>> Radeon Mobility X1400 on it.
>>
>> I've tried several ways to get my laptop TFT screen with a resolution of
>> 168ßx1050 and my LCD screen on my desk with a resolution of 1280x1024
>> running.
>>
>> Using SAX, I will only get one screen working correctly, the one with
>> the
>> higher resolution. On the other sreen, the desktop image doesn't fit
>> into
>> the screen, it's boarders remain outside. On my second screen on my desk
>> I
>> can't achieve a resolution of more then 1024x768.
>>
>> My second way was to try using aticonfig. In detail I've used the
>> following command:
>>
>> aticonfig --initial=dual-head --desktop-setup=clone
>> --resolution=Screen0,1680x1050 --resolution=Screen1,1280x1024
>> --hsync=Screen0,50-60 --vrefresh=Screen0,60 --hsync=Screen1,50-60
>> --vrefresh=Screen1,60
>>
>> The resulting xorg.conf will follow at the end of the Email. First let
>> me
>> describe, what is happening: The laptops screen (1680x1050) is displayed
>> correctly, the DELL 1907 FPT on my desk contains again a display, which
>> doesn't fit into the screen. However, the resolution is not ar
>> 1280x1024.
>> Follwoing another hint I've tried to "tune" my screens using the tool
>> application->system->configuration->ATI graphics adapter settings.
>> However
>> this tool forces me to restart the laptopn with the turn off und turn on
>> button, because the laptop didn't react to anything after applying
>> changes.
>>
>> Invoking SAX after such an aticonfig shows resolution of 600x800, so SAX
>> and aticonfig don't really understand each other, or clearer said: SAX
>> doesn't understand aticonfig configurations.
>>
>> So what I would like to have from you experts now is a hint what is
>> still
>> wrong in my xorg.conf. I rellay need help...
>
> I'm not sure if it is a configuration bug. More likely it's a driver
> bug or a hardware limitation you're hitting. I suggest to give the
> radeonhd driver a try instead.
>
> --> http://wiki.x.org/wiki/radeonhd
> -->
> http://download.opensuse.org/repositories/X11:/Drivers:/Video:/radeonhd/ope…
>
> And there's much more help you can expect. There is a mailinglist,
> freedesktop bugzilla and IRC.
>
I've installed the radeonhd driver with Yast from the repository above. A
first attempt to configure my dual head with sax2 brought the same bad
results as before. So: what must I do for configuring it right? The wiki
doesn't say anaythingt to the configuration, or at least I don't
understand it at all. Must I remove the ATI driver if I've installed the
radeonhd? If yes, what can I use instead of aticonfig? I Like to use
aticonfig, because this brought better results then Sax2. Sax2 gives me my
second monitor only in a resolution of 1024x786, aticonfig does 1280x1024.
However, using aticonfig the display doesn't fit onto my monitor
display... The best for me would be some suggestions what I should change
in the xorg.conf listed below,in order to get in correct:
First Monitor IBM LCD 1680x1050, 15 Inches
Second Monitor: DELL 1907 FPT 1280x1024, 19 Inches
Hoping for a lot of helpful answers :-)
Cheers
Alexander
#######################xorg.conf#########################
# /.../
# SaX generated X11 config file
# Created on: 2008-03-06T17:53:35+0100.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax(a)suse.de>, 2005
# Contact: SaX-User list
<https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#
Section "ServerLayout"
Identifier "Layout[all]"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "Mouse[3]" "SendCoreEvents"
Option "Clone" "off"
Option "Xinerama" "off"
EndSection
Section "Files"
InputDevices "/dev/gpmdata"
InputDevices "/dev/input/mice"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/URW"
FontPath "/usr/share/fonts/Speedo"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/latin2/misc:unscaled"
FontPath "/usr/share/fonts/latin2/75dpi:unscaled"
FontPath "/usr/share/fonts/latin2/100dpi:unscaled"
FontPath "/usr/share/fonts/latin2/Type1"
FontPath "/usr/share/fonts/latin7/75dpi:unscaled"
FontPath "/usr/share/fonts/baekmuk:unscaled"
FontPath "/usr/share/fonts/japanese:unscaled"
FontPath "/usr/share/fonts/kwintv"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/uni:unscaled"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/ucs/misc:unscaled"
FontPath "/usr/share/fonts/ucs/75dpi:unscaled"
FontPath "/usr/share/fonts/ucs/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/misc:unscaled"
FontPath "/usr/share/fonts/hellas/75dpi:unscaled"
FontPath "/usr/share/fonts/hellas/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/Type1"
FontPath "/usr/share/fonts/misc/sgi:unscaled"
FontPath "/usr/share/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "freetype"
Load "extmod"
Load "glx"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "on"
EndSection
Section "InputDevice"
Identifier "Keyboard[0]"
Driver "kbd"
Option "Protocol" "Standard"
Option "XkbLayout" "us"
Option "XkbModel" "microsoftpro"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Identifier "Mouse[1]"
Driver "synaptics"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Emulate3Buttons" "on"
Option "InputFashion" "Mouse"
Option "Name" "Synaptics;Touchpad"
Option "Protocol" "explorerps/2"
Option "SHMConfig" "on"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Mouse[3]"
Driver "mouse"
Option "ButtonNumber" "5"
Option "Device" "/dev/input/mice"
Option "EmulateWheel" "on"
Option "EmulateWheelButton" "2"
Option "InputFashion" "Mouse"
Option "Name" "IBM;TPPS/2 TrackPoint"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Mouse[5]"
Driver "mouse"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "TPPS/2 IBM TrackPoint"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "Modes"
Identifier "Modes[0]"
EndSection
Section "Monitor"
Identifier "Monitor[0]"
VendorName "IBM"
ModelName "IBM LCD MONITOR"
UseModes "Modes[0]"
DisplaySize 331 207
HorizSync 30.0 - 82.0
VertRefresh 43.0 - 60.0
Option "CalcAlgorithm" "XServerPool"
Option "DPMS"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[1]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "Device[0]"
Driver "fbdev"
VendorName "VESA"
BoardName "Framebuffer Graphics"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
Option "DesktopSetup" "clone"
Option "EnableMonitor" "lvds,tmds1"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "aticonfig-Device[1]"
Driver "fglrx"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen[0]"
Device "Device[0]"
Monitor "Monitor[0]"
SubSection "Display"
Depth 15
Modes "default"
EndSubSection
SubSection "Display"
Depth 16
Modes "default"
EndSubSection
SubSection "Display"
Depth 24
Modes "default"
EndSubSection
SubSection "Display"
Depth 32
Modes "default"
EndSubSection
SubSection "Display"
Depth 8
Modes "default"
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[1]"
Device "aticonfig-Device[1]"
Monitor "aticonfig-Monitor[1]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
--
To unsubscribe, e-mail: opensuse-xorg+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-xorg+help(a)opensuse.org
hi list,
somehow i got a problem with my xorg setup in suse10.3.
i notice that xfce uses the wrong resolution. Using xrandr i found it
used the (unused) VGA data instead of LCD.
what is correctly described as disabled with xrandr.
i can make xfce use the whole screen when using "xrandr --auto"
i have tried to fix xorg.conf by hand and with SAX2. there is no VGA configured.
any hints from here ?
re,
wh
note: this happens on my laptop so the LCD is the normal attached screen
and the VGA is the external output.
--
To unsubscribe, e-mail: opensuse-xorg+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-xorg+help(a)opensuse.org
Hi List,
I can manage it to get the dual head mode running correctly.
I have an IBM Lenovo T60 laptop, and OpenSuSE 10.3 installed on it, with a
Radeon Mobility X1400 on it.
I've tried several ways to get my laptop TFT screen with a resolution of
168ßx1050 and my LCD screen on my desk with a resolution of 1280x1024
running.
Using SAX, I will only get one screen working correctly, the one with the
higher resolution. On the other sreen, the desktop image doesn't fit into
the screen, it's boarders remain outside. On my second screen on my desk I
can't achieve a resolution of more then 1024x768.
My second way was to try using aticonfig. In detail I've used the
following command:
aticonfig --initial=dual-head --desktop-setup=clone
--resolution=Screen0,1680x1050 --resolution=Screen1,1280x1024
--hsync=Screen0,50-60 --vrefresh=Screen0,60 --hsync=Screen1,50-60
--vrefresh=Screen1,60
The resulting xorg.conf will follow at the end of the Email. First let me
describe, what is happening: The laptops screen (1680x1050) is displayed
correctly, the DELL 1907 FPT on my desk contains again a display, which
doesn't fit into the screen. However, the resolution is not ar 1280x1024.
Follwoing another hint I've tried to "tune" my screens using the tool
application->system->configuration->ATI graphics adapter settings. However
this tool forces me to restart the laptopn with the turn off und turn on
button, because the laptop didn't react to anything after applying
changes.
Invoking SAX after such an aticonfig shows resolution of 600x800, so SAX
and aticonfig don't really understand each other, or clearer said: SAX
doesn't understand aticonfig configurations.
So what I would like to have from you experts now is a hint what is still
wrong in my xorg.conf. I rellay need help...
Cheers
Alexander
############################cut here###########################
# /.../
# SaX generated X11 config file
# Created on: 2008-03-06T17:53:35+0100.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax(a)suse.de>, 2005
# Contact: SaX-User list
<https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#
Section "ServerLayout"
Identifier "Layout[all]"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "Mouse[3]" "SendCoreEvents"
Option "Clone" "off"
Option "Xinerama" "off"
EndSection
Section "Files"
InputDevices "/dev/gpmdata"
InputDevices "/dev/input/mice"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/URW"
FontPath "/usr/share/fonts/Speedo"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/latin2/misc:unscaled"
FontPath "/usr/share/fonts/latin2/75dpi:unscaled"
FontPath "/usr/share/fonts/latin2/100dpi:unscaled"
FontPath "/usr/share/fonts/latin2/Type1"
FontPath "/usr/share/fonts/latin7/75dpi:unscaled"
FontPath "/usr/share/fonts/baekmuk:unscaled"
FontPath "/usr/share/fonts/japanese:unscaled"
FontPath "/usr/share/fonts/kwintv"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/uni:unscaled"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/ucs/misc:unscaled"
FontPath "/usr/share/fonts/ucs/75dpi:unscaled"
FontPath "/usr/share/fonts/ucs/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/misc:unscaled"
FontPath "/usr/share/fonts/hellas/75dpi:unscaled"
FontPath "/usr/share/fonts/hellas/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/Type1"
FontPath "/usr/share/fonts/misc/sgi:unscaled"
FontPath "/usr/share/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "freetype"
Load "extmod"
Load "glx"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "on"
EndSection
Section "InputDevice"
Identifier "Keyboard[0]"
Driver "kbd"
Option "Protocol" "Standard"
Option "XkbLayout" "us"
Option "XkbModel" "microsoftpro"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Identifier "Mouse[1]"
Driver "synaptics"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Emulate3Buttons" "on"
Option "InputFashion" "Mouse"
Option "Name" "Synaptics;Touchpad"
Option "Protocol" "explorerps/2"
Option "SHMConfig" "on"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Mouse[3]"
Driver "mouse"
Option "ButtonNumber" "5"
Option "Device" "/dev/input/mice"
Option "EmulateWheel" "on"
Option "EmulateWheelButton" "2"
Option "InputFashion" "Mouse"
Option "Name" "IBM;TPPS/2 TrackPoint"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Mouse[5]"
Driver "mouse"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "TPPS/2 IBM TrackPoint"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "Modes"
Identifier "Modes[0]"
EndSection
Section "Monitor"
Identifier "Monitor[0]"
VendorName "IBM"
ModelName "IBM LCD MONITOR"
UseModes "Modes[0]"
DisplaySize 331 207
HorizSync 30.0 - 82.0
VertRefresh 43.0 - 60.0
Option "CalcAlgorithm" "XServerPool"
Option "DPMS"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[1]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "Device[0]"
Driver "fbdev"
VendorName "VESA"
BoardName "Framebuffer Graphics"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
Option "DesktopSetup" "clone"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "aticonfig-Device[1]"
Driver "fglrx"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen[0]"
Device "Device[0]"
Monitor "Monitor[0]"
SubSection "Display"
Depth 15
Modes "default"
EndSubSection
SubSection "Display"
Depth 16
Modes "default"
EndSubSection
SubSection "Display"
Depth 24
Modes "default"
EndSubSection
SubSection "Display"
Depth 32
Modes "default"
EndSubSection
SubSection "Display"
Depth 8
Modes "default"
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[1]"
Device "aticonfig-Device[1]"
Monitor "aticonfig-Monitor[1]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
--
To unsubscribe, e-mail: opensuse-xorg+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-xorg+help(a)opensuse.org
I posted on novell's forums about this but I doubt anyone at novell is
particularly concerned with opensuse. I apologize if I sent this question
to the wrong list, but xorg seemed the closest match to my problem since I'm
trying to get graphics card support. I looked through all kinds of junk
before i posted. Here's my problem:
To make a long story short, adding opensuse-community.org as a repository
was not working - it spent about ten minutes downloading who knows what (a
bunch of small files, judging from the speed with which the windows popped
up and disappeared), and then gave me a bunch of error messages. Fantastic.
I then removed every trace of ATI from yast, and tried to use this link:
opensuse-community.org/ati-legacy.ymp
That didn't seem as bad in terms of actually adding the repository, but then
I got this recommendation from yast due to a conflict:
#### YaST2 conflicts list - generated 2008-04-03 21:36:18 ####
This would invalidate atom:kernel-default-2.6.22.17-0.1.i586.
atom:kernel-default-2.6.22.17-0.1.i586 has unfulfilled requirements
=== atom:kernel-default-2.6.22.17-0.1.i586 ===
kernel-default-2.6.22.17-0.1.i586[openSUSE-10.3-Updates] provides
kernel-default == 2.6.22.17-0.1, but another version of that package is
already installed.
kernel-default-2.6.22.17-0.1.i586 provides kernel-default == 2.6.22.17-0.1,
but is scheduled to be uninstalled.
Can't satisfy requirement kernel-default >= 2.6.22.17-0.1 for
atom:kernel-default-2.6.22.17-0.1.i586
atom:kernel-default-2.6.22.17-0.1.i586 will be evaluated for installation
(freshened) by kernel-default-2.6.22.13-0.3.i586[openSUSE-10.3-Updates]
(kernel-default == 2.6.22.13-0.3)
(null)
Conflict Resolution:
( ) delete kernel-default
#### YaST2 conflicts list END ###
No thanks! Where should I go from here? I feel like the
opensuse-community.org should at least be notified that their repository
isn't working very well with openSUSE 10.3.
--
To unsubscribe, e-mail: opensuse-xorg+unsubscribe(a)opensuse.org
For additional commands, e-mail: opensuse-xorg+help(a)opensuse.org