- openSUSE Multimedia

USB Audio, Suse 9.2
by Sam Lewis 30 May '05

30 May '05

Hi, while trying to add a USB sound card (sound card driver: USB Audio; sound card model: USB Audio, Generic), the follwoing error message occures "The kernel model snd-usb-audio for sound support could not be loaded." How could I properly install a USB sound card on Suse 9.2? Any ideas? Thanks, Sam

1 0

problem with installing sound card
by sibil sibily 28 May '05

28 May '05

Hi Team, I have suse 8.0 on my PC with GA-8IPE1000-G mainboard with on board sound card that the name is "Realtek AC'97 audio". I receive the driver for this card from "realtek.com" site that the name is "linux_r32.zip" but i don't know how can i install and configure it that i can use of sound card. Would you please help me that install & configure that. Thanks for your help --------------------------------- Yahoo! Mail Mobile Take Yahoo! Mail with you! Check email on your mobile phone.

2 1

Logitech USB headset & SUSE 9.3
by Don Ahlskog 19 May '05

19 May '05

I can't output sound to my USB headset. Dmesg says it's there. Don Ahlskog Las Vegas,NV KE7DDA __________________________________ Do you Yahoo!? Take Yahoo! Mail with you! Get it on your mobile phone. http://mobile.yahoo.com/maildemo

1 0

SUSE9.3 and Terratec Cinergy 400
by Sami A. Hassanein 09 May '05

09 May '05

Hi I run SUSE9.3 and I use the TV card from Terratec Cinergy 400. Through YAST the card is detected but when I scan the channels nothing is being found. In the syslog I have the below listed entries Does anybode know what is wrong here and how can I fix it? May 8 16:44:29 apus kernel: saa7133[0]: found at 0000:03:00.0, rev: 240, irq: 10, latency: 0, mmio: 0x40800000 May 8 16:44:29 apus kernel: PCI: Setting latency timer of device 0000:03:00.0 to 64 May 8 16:44:29 apus kernel: saa7133[0]: subsystem: 153b:1162, board: Terratec Cinergy 400 TV [card=8,insmod option] May 8 16:44:29 apus kernel: saa7133[0]: board init: gpio is 40000 May 8 16:44:29 apus kernel: saa7133[0]: registered input device for IR May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout [bit=WRR] May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout [bit=WRR] May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 00: 3b 15 62 11 08 20 1c 55 43 43 a9 1c 55 43 43 a9 May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 10: 00 ff e6 07 00 00 00 00 00 00 00 00 00 00 00 00 May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 20: 01 00 02 02 01 3e 9b cb 91 03 03 00 07 00 01 00 May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 30: 00 02 02 00 00 00 00 00 00 00 00 00 00 00 00 00 May 8 16:44:30 apus modprobe: FATAL: Error inserting tuner (/lib/modules/2.6.11.4-20a-default/kernel/drivers/media/video/tuner.ko): Unknown symbol in module, or unknown parameter (see dmesg) May 8 16:44:30 apus kernel: tuner: Unknown parameter `tuner' May 8 16:44:30 apus kernel: load_module: err 0xfffffffe (dont worry) May 8 16:44:30 apus kernel: saa7133[0]: registered device video0 [v4l2] May 8 16:44:30 apus kernel: saa7133[0]: registered device vbi0 -- Any help is very much appreciated. Sami

3 2

Re: [suse-multimedia-e] SUSE9.3 and Terratec Cinergy 400
by Sami A. Hassanein 08 May '05

08 May '05

On Sunday 08 May 2005 18:17, you wrote: > You should set the tuner to 5 for that card it has a TUNER_PHILIPS_PAL > tuner according to the source code for the saa* driver I have looked at > for that card .... the only problem I have is I can't find the saa7133 > driver anywhere in my SuSE 9.3 Pro source. You will not find this on > menu, you will need to use the expert settings on the already configured > card in the TV card configure section of the YAST control center, or > pass that parm on as part of the boot command. > > A full recursive grep fails to find saa7133 in my source code except as > a mention in comments. Does this mean there is no way to use the TV card Terratec Cinergy 400 with suse 9.3. If so which TV card is supported for sure? -- Thanks, Sami

1 0

Re: [suse-multimedia-e] SUSE9.3 and Terratec Cinergy 400
by Sami A. Hassanein 08 May '05

08 May '05

On Sunday 08 May 2005 17:13, you wrote: > > I run SUSE9.3 and I use the TV card from Terratec Cinergy 400. > > Through YAST the card is detected but when I scan the channels nothing is > > being found. > > In the syslog I have the below listed entries > > > > Does anybode know what is wrong here and how can I fix it? > > > > May 8 16:44:29 apus kernel: saa7133[0]: found at 0000:03:00.0, rev: 240, > > irq: 10, latency: 0, mmio: 0x40800000 > > May 8 16:44:29 apus kernel: PCI: Setting latency timer of device > > 0000:03:00.0 to 64 > > May 8 16:44:29 apus kernel: saa7133[0]: subsystem: 153b:1162, board: > > Terratec Cinergy 400 TV [card=8,insmod option] > > May 8 16:44:29 apus kernel: saa7133[0]: board init: gpio is 40000 > > May 8 16:44:29 apus kernel: saa7133[0]: registered input device for IR > > May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout > > [bit=WRR] May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait > > timeout [bit=WRR] May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 00: > > 3b 15 62 11 08 20 1c 55 43 43 a9 1c 55 43 43 a9 > > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 10: 00 ff e6 07 00 00 > > 00 00 00 00 00 00 00 00 00 00 > > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 20: 01 00 02 02 01 3e > > 9b cb 91 03 03 00 07 00 01 00 > > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 30: 00 02 02 00 00 00 > > 00 00 00 00 00 00 00 00 00 00 > > May 8 16:44:30 apus modprobe: FATAL: Error inserting tuner > > (/lib/modules/2.6.11.4-20a-default/kernel/drivers/media/video/tuner.ko): > > Unknown symbol in module, or unknown parameter (see dmesg) > > May 8 16:44:30 apus kernel: tuner: Unknown parameter `tuner' > > May 8 16:44:30 apus kernel: load_module: err 0xfffffffe (dont worry) > > May 8 16:44:30 apus kernel: saa7133[0]: registered device video0 [v4l2] > > May 8 16:44:30 apus kernel: saa7133[0]: registered device vbi0 > > > > -- > > Any help is very much appreciated. > > Sami > > Which tuner did you have YAST assign to the card, TV video processing > chip and tuner are two seperate items. If I try to select a tuner under terratec cinergy 400 it says there is no tuner available? Which one do I have to select? -- Thanks for your help Sami

1 0

Avermedia Avertv Cardbus card
by Vakvarju 12 Apr '05

12 Apr '05

Hi all, I am trying to make working the above card in my notebook. I use SuSE Linux 9.0 with kernel 2.4.21-273-default. The Yast has recognised the card as SAA7134 but I have no idea what tuner to set up. Does anyone has any experience with this card? Thx. -- ________________________ /"\ Vakvarju \ / ASCII Ribbon Campaign vakvarju_at_spektrum-3d_dot_hu X Against HTML Mail / \

1 0

no sound out
by zhen zhang 22 Mar '05

22 Mar '05

Hello, I am using IBM NetVista 6830-CAU to SuSe8.1. The machine comes with a build-in speaker, and it works. However, when I plug in an extra speaker, the sound did not switch to it and still comes out from the machine. Any idea how to fix it? Thanks.

1 0

Re: [suse-multimedia-e] Skype and sound
by Steve King 18 Mar '05

18 Mar '05

That kind of solution worked for me with Skype. I used either kmix or kamix (forget which), so one of those has the microphone boost option. --- Tom Patton <thpnalb(a)micro-net.com> wrote: > Try using gamix instead of kmix. If your sound card > supports it, you > will notice a push-button for "mike boost", that > punches about 20db gain > to the mike. I have not tried Skype yet, so can't > help ya there... > > On Thu, 2005-03-17 at 21:18 -0800, Claus Olesen > wrote: > > Have you tried pulling at the slider(s) in > YaST/hardware/sound/volume? I'm not > > sure about how those and the ones in KMix relate. > > > > Do you have another PC that you could use for the > other end - to verify that > > the problem is not at the other end? > > > > I tried Skype a couple months ago from my SuSE 9.2 > to a Windows box and got no > > complaints. Besides, I'm impressed how well it > works - it was just like > > talking on a regular phone. > > > > Claus > > > > On Thursday 17 March 2005 10:07, Rene wrote: > > > I'm trying to get Skype (Internet-telefony) > working properly. > > > Reception is fine, but my counterpartners hardly > hear me. > > > In Kmix MIC is at maximum and the red button > switched on. > > > I hear myself loudly through the speakers, but I > am Hardly heared. > > > Settings under soundsystem are: > > > ALSA; full duplex, sample rate 48000 HZ, > standard quality, > > > soundsystem active, realtine priority, 8 > fragments 2048 bytes. > > > > > > Does anyone have an advice how to enhance the > volume of the microphone ? > > > > > > Thanks, > > > > > > Rene > > > > > -- > To unsubscribe send e-mail to > suse-multimedia-e-unsubscribe(a)suse.com > For additional commands send e-mail to > suse-multimedia-e-help(a)suse.com > > -- Knowledge is knowing a tomato is a fruit. Wisdom is knowing not to put it in a fruit salad.

1 0

Skype and sound
by Rene 18 Mar '05

18 Mar '05

I'm trying to get Skype (Internet-telefony) working properly. Reception is fine, but my counterpartners hardly hear me. In Kmix MIC is at maximum and the red button switched on. I hear myself loudly through the speakers, but I am Hardly heared. Settings under soundsystem are: ALSA; full duplex, sample rate 48000 HZ, standard quality, soundsystem active, realtine priority, 8 fragments 2048 bytes. Does anyone have an advice how to enhance the volume of the microphone ? Thanks, Rene

3 2