Hi,
while trying to add a USB sound card (sound card driver: USB Audio;
sound card model: USB Audio, Generic), the follwoing error message
occures "The kernel model snd-usb-audio for sound support could not be
loaded."
How could I properly install a USB sound card on Suse 9.2? Any ideas?
Thanks, Sam
Hi Team,
I have suse 8.0 on my PC with GA-8IPE1000-G mainboard with on board sound card that the name is "Realtek AC'97 audio". I receive the driver for this card from "realtek.com" site that the name is "linux_r32.zip" but i don't know how can i install and configure it that i can use of sound card.
Would you please help me that install & configure that.
Thanks for your help
---------------------------------
Yahoo! Mail Mobile
Take Yahoo! Mail with you! Check email on your mobile phone.
I can't output sound to my USB headset.
Dmesg says it's there.
Don Ahlskog
Las Vegas,NV
KE7DDA
__________________________________
Do you Yahoo!?
Take Yahoo! Mail with you! Get it on your mobile phone.
http://mobile.yahoo.com/maildemo
Hi
I run SUSE9.3 and I use the TV card from Terratec Cinergy 400.
Through YAST the card is detected but when I scan the channels nothing is
being found.
In the syslog I have the below listed entries
Does anybode know what is wrong here and how can I fix it?
May 8 16:44:29 apus kernel: saa7133[0]: found at 0000:03:00.0, rev: 240, irq:
10, latency: 0, mmio: 0x40800000
May 8 16:44:29 apus kernel: PCI: Setting latency timer of device 0000:03:00.0
to 64
May 8 16:44:29 apus kernel: saa7133[0]: subsystem: 153b:1162, board: Terratec
Cinergy 400 TV [card=8,insmod option]
May 8 16:44:29 apus kernel: saa7133[0]: board init: gpio is 40000
May 8 16:44:29 apus kernel: saa7133[0]: registered input device for IR
May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout [bit=WRR]
May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout [bit=WRR]
May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 00: 3b 15 62 11 08 20 1c
55 43 43 a9 1c 55 43 43 a9
May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 10: 00 ff e6 07 00 00 00
00 00 00 00 00 00 00 00 00
May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 20: 01 00 02 02 01 3e 9b
cb 91 03 03 00 07 00 01 00
May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 30: 00 02 02 00 00 00 00
00 00 00 00 00 00 00 00 00
May 8 16:44:30 apus modprobe: FATAL: Error inserting tuner
(/lib/modules/2.6.11.4-20a-default/kernel/drivers/media/video/tuner.ko):
Unknown symbol in module, or unknown parameter (see dmesg)
May 8 16:44:30 apus kernel: tuner: Unknown parameter `tuner'
May 8 16:44:30 apus kernel: load_module: err 0xfffffffe (dont worry)
May 8 16:44:30 apus kernel: saa7133[0]: registered device video0 [v4l2]
May 8 16:44:30 apus kernel: saa7133[0]: registered device vbi0
--
Any help is very much appreciated.
Sami
On Sunday 08 May 2005 18:17, you wrote:
> You should set the tuner to 5 for that card it has a TUNER_PHILIPS_PAL
> tuner according to the source code for the saa* driver I have looked at
> for that card .... the only problem I have is I can't find the saa7133
> driver anywhere in my SuSE 9.3 Pro source. You will not find this on
> menu, you will need to use the expert settings on the already configured
> card in the TV card configure section of the YAST control center, or
> pass that parm on as part of the boot command.
>
> A full recursive grep fails to find saa7133 in my source code except as
> a mention in comments.
Does this mean there is no way to use the TV card Terratec Cinergy 400 with
suse 9.3.
If so which TV card is supported for sure?
--
Thanks,
Sami
On Sunday 08 May 2005 17:13, you wrote:
> > I run SUSE9.3 and I use the TV card from Terratec Cinergy 400.
> > Through YAST the card is detected but when I scan the channels nothing is
> > being found.
> > In the syslog I have the below listed entries
> >
> > Does anybode know what is wrong here and how can I fix it?
> >
> > May 8 16:44:29 apus kernel: saa7133[0]: found at 0000:03:00.0, rev: 240,
> > irq: 10, latency: 0, mmio: 0x40800000
> > May 8 16:44:29 apus kernel: PCI: Setting latency timer of device
> > 0000:03:00.0 to 64
> > May 8 16:44:29 apus kernel: saa7133[0]: subsystem: 153b:1162, board:
> > Terratec Cinergy 400 TV [card=8,insmod option]
> > May 8 16:44:29 apus kernel: saa7133[0]: board init: gpio is 40000
> > May 8 16:44:29 apus kernel: saa7133[0]: registered input device for IR
> > May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout
> > [bit=WRR] May 8 16:44:29 apus kernel: saa7133[0]: dsp access wait
> > timeout [bit=WRR] May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 00:
> > 3b 15 62 11 08 20 1c 55 43 43 a9 1c 55 43 43 a9
> > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 10: 00 ff e6 07 00 00
> > 00 00 00 00 00 00 00 00 00 00
> > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 20: 01 00 02 02 01 3e
> > 9b cb 91 03 03 00 07 00 01 00
> > May 8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 30: 00 02 02 00 00 00
> > 00 00 00 00 00 00 00 00 00 00
> > May 8 16:44:30 apus modprobe: FATAL: Error inserting tuner
> > (/lib/modules/2.6.11.4-20a-default/kernel/drivers/media/video/tuner.ko):
> > Unknown symbol in module, or unknown parameter (see dmesg)
> > May 8 16:44:30 apus kernel: tuner: Unknown parameter `tuner'
> > May 8 16:44:30 apus kernel: load_module: err 0xfffffffe (dont worry)
> > May 8 16:44:30 apus kernel: saa7133[0]: registered device video0 [v4l2]
> > May 8 16:44:30 apus kernel: saa7133[0]: registered device vbi0
> >
> > --
> > Any help is very much appreciated.
> > Sami
>
> Which tuner did you have YAST assign to the card, TV video processing
> chip and tuner are two seperate items.
If I try to select a tuner under terratec cinergy 400 it says there is no
tuner available? Which one do I have to select?
--
Thanks for your help
Sami