October 2005 - openSUSE AMD64 - openSUSE Mailing Lists

Problems
by gilligan 25 Oct '05

25 Oct '05

I am having problems running 10.0. DLed it (DVD version) and it install great but, when it does its last reboot I hear the music but my monitor(Viewsonic VE910b) reports Out of Range. I've tried setting the resolution at 1024 X 768 but nothing works. Even tried using my wifes monitor(el cheapo) and her's blanks the monitor. Help! Please. Video card is an ATI AIW x600. Thanks

3 2

RE: [suse-amd64] strategy for gigabyte dual nic board in 9.3
by Black, Alain 24 Oct '05

24 Oct '05

I would probably set up a static IP address for the PC to PC cross-over cable (one per host attached to the cable) that is on a different subnet than the rest of your internal network. NIC0 to internal network being 192.168.0.xxx NIC1 direct to other PC being 192.168.1.xxx NICn on other PC directly connected being 192.168.1.xxx+1 -Alain -----Original Message----- From: Johan Nielsen [mailto:yep@osterbo-net.dk] Sent: Monday, November 28, 2005 1:58 AM To: suse-amd64(a)suse.com Subject: Re: [suse-amd64] strategy for gigabyte dual nic board in 9.3 Mandag 17 oktober 2005 18:00 skrev Black, Alain: > Mark, > > On my dual NIC systems under 9.3, I only configure the NIC that I want > to use. Otherwise on boot the system will spend 20 seconds waiting for > DHCP to timeout for the NIC that isn't plugged in. > > I would recommend deconfiguring the NIC that you don't want to use at > this time, and then only configure it when you're ready to use it. > > -Alain. > Now if you wanted to use one NIC for external traffic and the other for internal traffic on the local lan how would one attack this given. 1. NIC connected to the same switch with other PC's that's behind a router (Zywall 5) 2. PC to PC with patched cable This would mainly/basicly be used to move large sets of data my "data" repository. Good suggestions is very welcome. Johan > -----Original Message----- > From: mark pryor [mailto:tlviewer@yahoo.com] > Sent: Friday, October 14, 2005 1:56 PM > To: suse-amd64(a)suse.com > Subject: [suse-amd64] strategy for gigabyte dual nic board in 9.3 > > hello, > > SuSE 9.3 x86_64 > system: > Gigabyte ga-k8n ultra-9 > Asus 6800 EN Nvidia pci-x video > 1 GB Ocz 2-3-2-5 RAM > hd: WD 2500JD SATA (JBOD nv_sata_0) > > I'm having trouble setting up the two LAN devices in > Yast network devices. > > In the manual, it shows the LAN1 (Marvel) as connected > to the (faster) pci-x bus. I only want to connect a > single cable at this time. When I configure both > devices, the system rolls over: I lose SAMBA and > bootup behavior is inconsistent. > > If you are going to setup both devices, what setting > do you give "device activation" in the "detailed > network settings" window? I tried hotplug for both > (bad), "at boot" for LAN1 and hotplug for LAN2 (bad). > I finally decided to disable LAN2 in the bios and > delete it in Yast Network devices. Then LAN1 is set to > activate at boot. > > This solution (to disable LAN2) seems extreme. I'm > guessing I ran into trouble since at one point I gave > both devices the same settings. If I tried to change > them something wouldn't reset. > > This is the first board I've setup with dual onboard > LAN -- what a head-ache. > > thanks for your comments, > Mark Pryor (the one with no political ambitions) > > > > __________________________________ > Yahoo! Music Unlimited > Access over 1 million songs. Try it free. > http://music.yahoo.com/unlimited/ > > -- > Check the List-Unsubscribe header to unsubscribe > For additional commands, email: suse-amd64-help(a)suse.com -- Check the List-Unsubscribe header to unsubscribe For additional commands, email: suse-amd64-help(a)suse.com

1 0

gcc 4.0.2 for suse 9.3
by Argiris Mokios 24 Oct '05

24 Oct '05

Hi, I just wanted to ask if there is an rpm version of gcc 4.0.2 for suse 9.3. or I have to compile it from source. I can see there is one in ftp.suse.pub/projects/gcc/GCC4.0.x-Test/9.3-x86_64 but the name implys that is a test version. Regards. Argiris._ -- Epur Si Muove

1 0

apt-get errors in 9.3
by Constantine 'Gus' Fantanas 24 Oct '05

24 Oct '05

Hi, I get unsigned-packages errors in apt-get and synaptic for 9.3. In synaptic, I specifically unchecked "Check Signatures," but I still get the same error. It seems the apt-get site was updated within the past week or so. The downloads are much quicker, too. Any ideas? UPS is bringing my 10.0 :) , but I am installing 9.3 on a friend's computer; he wants his computer "yesterday." This is a frustrating experience because these errors prevent me, among other things, from installing the "good" media players, which depend on libraries such as 'lib-xine', which must be installed in the place of SuSE's politically-correct 'xine-lib'. I think that SuSE should reconsider its policy of eviscerating its media players and assorted libraries. CF

2 1

RE: [suse-amd64] strategy for gigabyte dual nic board in 9.3
by Black, Alain 23 Oct '05

23 Oct '05

Mark, On my dual NIC systems under 9.3, I only configure the NIC that I want to use. Otherwise on boot the system will spend 20 seconds waiting for DHCP to timeout for the NIC that isn't plugged in. I would recommend deconfiguring the NIC that you don't want to use at this time, and then only configure it when you're ready to use it. -Alain. -----Original Message----- From: mark pryor [mailto:tlviewer@yahoo.com] Sent: Friday, October 14, 2005 1:56 PM To: suse-amd64(a)suse.com Subject: [suse-amd64] strategy for gigabyte dual nic board in 9.3 hello, SuSE 9.3 x86_64 system: Gigabyte ga-k8n ultra-9 Asus 6800 EN Nvidia pci-x video 1 GB Ocz 2-3-2-5 RAM hd: WD 2500JD SATA (JBOD nv_sata_0) I'm having trouble setting up the two LAN devices in Yast network devices. In the manual, it shows the LAN1 (Marvel) as connected to the (faster) pci-x bus. I only want to connect a single cable at this time. When I configure both devices, the system rolls over: I lose SAMBA and bootup behavior is inconsistent. If you are going to setup both devices, what setting do you give "device activation" in the "detailed network settings" window? I tried hotplug for both (bad), "at boot" for LAN1 and hotplug for LAN2 (bad). I finally decided to disable LAN2 in the bios and delete it in Yast Network devices. Then LAN1 is set to activate at boot. This solution (to disable LAN2) seems extreme. I'm guessing I ran into trouble since at one point I gave both devices the same settings. If I tried to change them something wouldn't reset. This is the first board I've setup with dual onboard LAN -- what a head-ache. thanks for your comments, Mark Pryor (the one with no political ambitions) __________________________________ Yahoo! Music Unlimited Access over 1 million songs. Try it free. http://music.yahoo.com/unlimited/ -- Check the List-Unsubscribe header to unsubscribe For additional commands, email: suse-amd64-help(a)suse.com

2 1

SuSE 10, sound and Thinkpad
by David 22 Oct '05

22 Oct '05

I realize that this is not a amd64 question so I am sorry if it is inappropiate. I have asked on several forums and not had one reply. The folks here are very knowledgable so I am hoping someone has an idea for me. I have installed Novell/SuSE 10.0 on my trusty IBM Thinkpad 600e. I have used this TP for several years, starting with SuSE 9.0. It has worked great. I did have a few problems starting the sound with 9.0 but managed to get it going. When I used it with 9.2 I had absolutly no problem with anything other than APM. Sound worked great. With this same new laptop I have not been able to make the soind work correctly at all. If I go into YaST>Hardware>Sound I show two sound cards. CS4239 that will not open for editing, nor can it be deleted. I have to delete the sound file from /etc/modprobe.d. When this is done the other sound card(CS4610 Sound Fusion Audio Acceleraror. Using Driver snd-CS4232) in the sound configuration window can be edited as sound card 0. I can set the parameters to what they should be and the test sound plays great. Nothing else will play through the speakers. After a reboot only chirps and scratchy stuff will come out of the speakers even the test sound plays this way. If I go back to the yast sound configuration page and edit using advanced setup all the parameters are correct but I need to highlight them and press set. Then the test sound will play as before, but nothing else plays at all. If I try to set the volume plugin in my gkrellm there is no device available. Using Kmix the tray icon show a red x and has no controls when opened. I have tried other solutions, alsaconf, modprobe,etc. and have had the same results. David

2 2

Re: [suse-ia64] Re: [Openwbem-public] OpenWbem... is this what I need???
by Andy 19 Oct '05

19 Oct '05

To be more clear I put a screenshot from what I saw. It is not webmin, not VNC... it is... I don't know what it is :) Look here: http://www.ar-sd.net/resources/web_interface.jpg Regards, Andy. ----- Original Message ----- From: "Nick Snellock" <nick(a)mccomputing.co.uk> To: <suse-ia64(a)suse.com> Sent: Wednesday, October 19, 2005 12:03 PM Subject: Re: [suse-ia64] Re: [Openwbem-public] OpenWbem... is this what I need??? >I think that you probably need webmin rather than OPenWbem. OpenWbem is >used > to manage a network of machines rather than just one server. > > Nick > > On Wednesday 19 October 2005 08:18, Andy wrote: >> But is there a web admin interface for SLES 9? >> >> VNC works, but from what I see in SLES8 there is a web interface >> administration tool. In 9? >> >> This is the first time that I install a Enterprise Server ... trying to >> figure out "the best" of it. >> >> Andy. >> >> ----- Original Message ----- >> From: "Bart Whiteley" <bwhiteley(a)suse.com> >> To: <openwbem-public(a)lists.sourceforge.net> >> Cc: <suse-amd64(a)suse.com>; <suse-ia64(a)suse.com> >> Sent: Tuesday, October 18, 2005 8:01 PM >> Subject: Re: [Openwbem-public] OpenWbem... is this what I need??? >> >> > On Tuesday 18 October 2005 10:37 am, Andy wrote: >> >> Hi to all, >> >> >> >> I just installed Suse Enterprise 9 and I read in the documentation >> >> that >> >> there is a web administration interface for managing the server. Is >> >> this >> >> OpenWbem??? ... if yes then.... HOW Do I use it? I'm trying to make it >> >> work >> >> somehow, but can't find the "main ideea".I followed >> >> http://www.novell.com/coolsolutions/feature/14625.html these >> >> suggestions, >> >> but still don't get the main Ideea. >> >> >> >> Am I missing something? >> >> >> >> I saw a screenshot from SLES 8 web interface from a browser, it looked >> >> really ok... I want the same in SLES 9. >> > >> > OpenWBEM does use HTTP, but not HTML. It speaks CIM-XML. You can't >> > talk >> > to >> > the OpenWBEM CIMOM with a web browser; you need a CIM client. One way >> > to >> > access the CIMOM through a web browser is through the health monitoring >> > pages >> > of Novell's iManager. >> > >> > -- >> > Bart Whiteley >> > >> > >> > ------------------------------------------------------- >> > This SF.Net email is sponsored by: >> > Power Architecture Resource Center: Free content, downloads, >> > discussions, >> > and more. http://solutions.newsforge.com/ibmarch.tmpl >> > _______________________________________________ >> > Openwbem-public mailing list >> > Openwbem-public(a)lists.sourceforge.net >> > https://lists.sourceforge.net/lists/listinfo/openwbem-public > >

1 0

Re: [Openwbem-public] OpenWbem... is this what I need???
by Andy 19 Oct '05

19 Oct '05

But is there a web admin interface for SLES 9? VNC works, but from what I see in SLES8 there is a web interface administration tool. In 9? This is the first time that I install a Enterprise Server ... trying to figure out "the best" of it. Andy. ----- Original Message ----- From: "Bart Whiteley" <bwhiteley(a)suse.com> To: <openwbem-public(a)lists.sourceforge.net> Cc: <suse-amd64(a)suse.com>; <suse-ia64(a)suse.com> Sent: Tuesday, October 18, 2005 8:01 PM Subject: Re: [Openwbem-public] OpenWbem... is this what I need??? > On Tuesday 18 October 2005 10:37 am, Andy wrote: >> Hi to all, >> >> I just installed Suse Enterprise 9 and I read in the documentation that >> there is a web administration interface for managing the server. Is this >> OpenWbem??? ... if yes then.... HOW Do I use it? I'm trying to make it >> work >> somehow, but can't find the "main ideea".I followed >> http://www.novell.com/coolsolutions/feature/14625.html these >> suggestions, >> but still don't get the main Ideea. >> >> Am I missing something? >> >> I saw a screenshot from SLES 8 web interface from a browser, it looked >> really ok... I want the same in SLES 9. >> > > OpenWBEM does use HTTP, but not HTML. It speaks CIM-XML. You can't talk > to > the OpenWBEM CIMOM with a web browser; you need a CIM client. One way to > access the CIMOM through a web browser is through the health monitoring > pages > of Novell's iManager. > > -- > Bart Whiteley > > > ------------------------------------------------------- > This SF.Net email is sponsored by: > Power Architecture Resource Center: Free content, downloads, discussions, > and more. http://solutions.newsforge.com/ibmarch.tmpl > _______________________________________________ > Openwbem-public mailing list > Openwbem-public(a)lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/openwbem-public > >

1 0

OpenWbem... is this what I need???
by Andy 18 Oct '05

18 Oct '05

Hi to all, I just installed Suse Enterprise 9 and I read in the documentation that there is a web administration interface for managing the server. Is this OpenWbem??? ... if yes then.... HOW Do I use it? I'm trying to make it work somehow, but can't find the "main ideea".I followed http://www.novell.com/coolsolutions/feature/14625.html these suggestions, but still don't get the main Ideea. Am I missing something? I saw a screenshot from SLES 8 web interface from a browser, it looked really ok... I want the same in SLES 9. Regards, Andy.

1 0

mod_dav_svn not included with SuSE 10?
by Dan Chesmore 18 Oct '05

18 Oct '05

I am unable to find the mod_dav_svn.so file on my newly installed SuSE 10 GE install. I have all things installed for subversion along with almost all things apache2 installed. I am almost wondering if it was somehow missed. Has anyone seen this before or got it to work already. Thanks. -- Dan Chesmore Systems Admin Mediture 7700 Equitable Dr Suite 100 Eden Prairie, MN 55344 952-400-0315 www.mediture.com

1 0