September 2011 - openSUSE Virtual - openSUSE Mailing Lists

Re: [opensuse-virtual] PCI resource alignment command changed in 11.4? (non-page-aligned MMIO error)
by Kulkarni, Shanti 23 Sep '11

23 Sep '11

On Thu, Sep 22, 2011 at 3:03 AM, Jan Beulich <JBeulich(a)suse.com> wrote: >>>> On 22.09.11 at 07:26, Shanti Kulkarni <sk-public(a)revenant.org> wrote: >> I have a Dom0 which I upgraded from 11.2 (with OBS 4.0.2 Xen packages) to >> 11.4. One of my PVMs has a PCI card passed through. After the upgrade I am >> getting "non-page-aligned MMIO BAR" errors when attempting to launch that VM >> with the same kernel command line. Is there a different way to tell the >> kernel this information? >> >> I was passing a PCI USB/firewire card which had three PCI IDs: 04:00.0 >> (USB), 04:00.1 (USB 2), and 04:01.0 (firewire). Before upgrading, I could >> avoid that error and start the domain using the pci=resource_alignment kernel >> parameter in grub: >> >> module /vmlinuz-2.6.37.6-0.7-xen root=/dev/sys/root elevator=deadline >> swiotlb=force,256 iommu=soft pciback.permissive >> pciback.hide=(00:14.2)(04:00.0)(04:00.1)(04:01.0) >> pci=resource_alignment=00:14.2;04:00.0;04:00.1;04:01.0 radeon.modeset=0 >> vga=0x317 >> >> After upgrading, I this error when launching the PVM: "0000:04:00.1: >> non-page-aligned MMIO BAR found." I have tried changing the syntax of the >> resource_alignment command. I have also tried using other commands, such as >> reassigndev= and reassign_resources. >> >> I tried setting "(pci-passthrough-strict-check no)" in xend-config.sxp. Then >> the PVM launched, but oopsed when udev loaded. >> >> Has this command changed, or is it's syntax different? I'd appreciate any > > Supposedly not. > > As there are a number of kernel messages associated with this, you > should have provided there full kernel log (ideally for both old and > new kernels, but I'd expect you don't have the old one anymore). > > Jan > >> help you can provide. Here's some of the packages on my Dom0: >> >> kernel-xen-2.6.37.6-0.7.1.x86_64 >> kernel-xen-base-2.6.37.6-0.7.1.x86_64 >> kernel-xen-devel-2.6.37.6-0.7.1.x86_64 >> patterns-openSUSE-xen_server-11.4-6.9.1.x86_64 >> xen-4.0.2_52-0.2.1.x86_64 >> xen-doc-html-4.0.2_52-0.2.1.x86_64 >> xen-doc-pdf-4.0.2_52-0.2.1.x86_64 >> xen-libs-4.0.2_52-0.2.1.x86_64 >> xen-tools-4.0.2_52-0.2.1.x86_64 >> >> Thank you, >> Shanti-- >> To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org >> For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org > > > > Rats. I was hoping there was just some change in the syntax. Here is the kernel log for the new kernel (2.6.37). You're correct that I no longer have the old kernel installed. From my limited research on the subject I think the entry "[ 0.188870] pci 0000:04:00.1: reg 10: [mem 0xfe6fec00-0xfe6fecff]" means that the offending device is not being realigned, otherwise it would start on a multiple of 0x1000. The only kernel messages when I create the VM is the NIC going into promiscuous mode and forwarding state. I would appreciate any advice or suggestions that come to mind. Thanks, Shanti [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.37.6-0.7-xen (geeko@buildhost) (gcc version 4.5.1 20101208 [gcc-4_5-branch revision 167585] (SUSE Linux) ) #1 SMP 2011-07-21 02:17:24 +0200 [ 0.000000] Command line: root=/dev/sys/root elevator=deadline swiotlb=force,256 iommu=soft pciback.permissive pciback.hide=(00:14.2)(04:00.0)(04:00.1)(04:01.0) pci=resource_alignment=00:14.2;04:00.0;04:00.1;04:01.0 radeon.modeset=0 vga=0x317 [ 0.000000] Xen-provided machine memory map: [ 0.000000] BIOS: 0000000000000000 - 000000000009e000 (usable) [ 0.000000] BIOS: 000000000009e000 - 00000000000a0000 (reserved) [ 0.000000] BIOS: 00000000000e2000 - 0000000000100000 (reserved) [ 0.000000] BIOS: 0000000000100000 - 00000000cff90000 (usable) [ 0.000000] BIOS: 00000000cff90000 - 00000000cff9e000 (ACPI data) [ 0.000000] BIOS: 00000000cff9e000 - 00000000cffe0000 (ACPI NVS) [ 0.000000] BIOS: 00000000cffe0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] BIOS: 0000000100000000 - 0000000210000000 (usable) [ 0.000000] Xen-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 00000001d2a74000 (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI present. [ 0.000000] DMI: MSI MS-7642/890GXM-G65 (MS-7642) , BIOS V1.7 09/07/2010 [ 0.000000] last_pfn = 0x1d2a74 max_arch_pfn = 0x80000000 [ 0.000000] last_pfn = 0x100000 max_arch_pfn = 0x80000000 [ 0.000000] found SMP MP-table at [ffffffffff5fa780] 000ff780 [ 0.000000] initial memory mapped : 0 - 00000000 [ 0.000000] init_memory_mapping: 0000000000000000-0000000100000000 [ 0.000000] 0000000000 - 0100000000 page 4k [ 0.000000] kernel direct mapping tables up to 100000000 @ 1bbf000-23c4000 [ 0.000000] init_memory_mapping: 0000000100000000-00000001d2a74000 [ 0.000000] 0100000000 - 01d2a74000 page 4k [ 0.000000] kernel direct mapping tables up to 1d2a74000 @ 3259000-40f8000 [ 0.000000] RAMDISK: 00995000 - 01bab000 [ 0.000000] ACPI: RSDP 00000000000fac60 00014 (v00 ACPIAM) [ 0.000000] ACPI: RSDT 00000000cff90000 00040 (v01 7642MS A7642100 20100907 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000cff90200 00084 (v01 7642MS A7642100 20100907 MSFT 00000097) [ 0.000000] ACPI: DSDT 00000000cff905d0 05E0E (v01 A7642 A7642100 00000100 INTL 20051117) [ 0.000000] ACPI: FACS 00000000cff9e000 00040 [ 0.000000] ACPI: APIC 00000000cff90390 0007C (v01 7642MS A7642100 20100907 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000cff90410 0003C (v01 7642MS OEMMCFG 20100907 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000cff9e040 00072 (v01 7642MS A7642100 20100907 MSFT 00000097) [ 0.000000] ACPI: SRAT 00000000cff9a5d0 00108 (v03 AMD FAM_F_10 00000002 AMD 00000001) [ 0.000000] ACPI: HPET 00000000cff9a6e0 00038 (v01 7642MS OEMHPET 20100907 MSFT 00000097) [ 0.000000] ACPI: SSDT 00000000cff9a720 00DA4 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x001d2a74 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x001d2274 [ 0.000000] 0: 0x001d2a74 -> 0x001d2a74 [ 0.000000] On node 0 totalpages: 1909364 [ 0.000000] free_area_init_node: node 0, pgdat ffffffff80818b40, node_mem_map ffff8801cbc5a000 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4040 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 1030200 pages, LIFO batch:31 [ 0.000000] Normal zone: 11797 pages used for memmap [ 0.000000] Normal zone: 848991 pages, LIFO batch:31 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 6, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:2ec00000) [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:6 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 18 pages/cpu @ffff8801cad19000 s43648 r8192 d21888 u73728 [ 0.000000] pcpu-alloc: s43648 r8192 d21888 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Swapping MFNs for PFN 839 and 1cad1f (MFN 208839 and f7ab) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1883231 [ 0.000000] Kernel command line: root=/dev/sys/root elevator=deadline swiotlb=force,256 iommu=soft pciback.permissive pciback.hide=(00:14.2)(04:00.0)(04:00.1)(04:01.0) pci=resource_alignment=00:14.2;04:00.0;04:00.1;04:01.0 radeon.modeset=0 vga=0x317 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] allocated 76456480 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Software IO TLB enabled: [ 0.000000] Aperture: 64 megabytes [ 0.000000] Address size: 27 bits [ 0.000000] Kernel range: ffff8801c1826000 - ffff8801c5826000 [ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.000000] Memory: 7321100k/7645648k available (4685k kernel code, 8192k absent, 316356k reserved, 3696k data, 392k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] nr_pirqs: 728 [ 0.000000] NR_IRQS:34880 nr_irqs:2840 16 [ 0.000000] Xen reported: 3200.172 MHz processor. [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [xvc-1] enabled [ 0.080001] Calibrating delay using timer specific routine.. 6403.32 BogoMIPS (lpj=12806649) [ 0.080127] pid_max: default: 32768 minimum: 301 [ 0.080232] Security Framework initialized [ 0.080305] AppArmor: AppArmor initialized [ 0.080386] Mount-cache hash table entries: 256 [ 0.080525] Initializing cgroup subsys ns [ 0.080589] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.080666] Initializing cgroup subsys cpuacct [ 0.080729] Initializing cgroup subsys memory [ 0.080797] Initializing cgroup subsys devices [ 0.080860] Initializing cgroup subsys freezer [ 0.080922] Initializing cgroup subsys net_cls [ 0.080984] Initializing cgroup subsys blkio [ 0.081076] mce: CPU supports 6 MCE banks [ 0.081164] SMP alternatives: switching to UP code [ 0.093340] ACPI: Core revision 20101013 [ 0.100664] SMP alternatives: switching to SMP code [ 0.113087] Brought up 6 CPUs [ 0.113211] devtmpfs: initialized [ 0.113211] regulator: core version 0.5 [ 0.113211] regulator: dummy: [ 0.113211] Time: 13:05:15 Date: 09/22/11 [ 0.113211] NET: Registered protocol family 16 [ 0.113211] node 0 link 0: io port [1000, ffffff] [ 0.113211] TOM: 00000000d0000000 aka 3328M [ 0.113211] Fam 10h mmconf [e0000000, efffffff] [ 0.113211] node 0 link 0: mmio [a0000, bffff] [ 0.113211] node 0 link 0: mmio [d0000000, efffffff] ==> [d0000000, dfffffff] [ 0.113211] node 0 link 0: mmio [f0000000, fe2fffff] [ 0.113211] node 0 link 0: mmio [fe300000, fe4fffff] [ 0.113211] node 0 link 0: mmio [fe500000, ffdfffff] [ 0.113211] TOM2: 0000000230000000 aka 8960M [ 0.113211] bus: [00, 07] on node 0 link 0 [ 0.113211] bus: 00 index 0 [io 0x0000-0xffff] [ 0.113211] bus: 00 index 1 [mem 0x000a0000-0x000bffff] [ 0.113211] bus: 00 index 2 [mem 0xd0000000-0xdfffffff] [ 0.113211] bus: 00 index 3 [mem 0xf0000000-0xffffffff] [ 0.113211] bus: 00 index 4 [mem 0x230000000-0xfcffffffff] [ 0.113211] ACPI: bus type pci registered [ 0.113211] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.113211] PCI: not using MMCONFIG [ 0.113211] PCI: Using configuration type 1 for base access [ 0.113211] bio: create slab <bio-0> at 0 [ 0.116488] ACPI: EC: Look up EC in DSDT [ 0.117582] ACPI: Executed 4 blocks of module-level executable AML code [ 0.128645] ACPI: Interpreter enabled [ 0.128730] ACPI: (supports S0 S1 S5) [ 0.128961] ACPI: Using IOAPIC for interrupt routing [ 0.129052] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.130217] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources [ 0.140734] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.140986] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.141313] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.152071] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.160070] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.168070] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.176070] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.176963] ACPI Exception: AE_NOT_FOUND, Evaluating _PRW (20101013/scan-743) [ 0.177920] ACPI: No dock devices found. [ 0.177983] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.178324] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.178632] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 0.178697] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 0.178777] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 0.178855] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] [ 0.178936] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xdfffffff] [ 0.179013] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff] [ 0.179106] pci 0000:00:00.0: [1022:9601] type 0 class 0x000600 [ 0.179176] pci 0000:00:01.0: [1022:9602] type 1 class 0x000604 [ 0.179227] pci 0000:00:02.0: [1022:9603] type 1 class 0x000604 [ 0.179270] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold [ 0.179273] pci 0000:00:02.0: PME# disabled [ 0.179292] pci 0000:00:04.0: [1022:9604] type 1 class 0x000604 [ 0.179335] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.179337] pci 0000:00:04.0: PME# disabled [ 0.179356] pci 0000:00:05.0: [1022:9605] type 1 class 0x000604 [ 0.179398] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold [ 0.179400] pci 0000:00:05.0: PME# disabled [ 0.179419] pci 0000:00:06.0: [1022:9606] type 1 class 0x000604 [ 0.179461] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold [ 0.179463] pci 0000:00:06.0: PME# disabled [ 0.179500] pci 0000:00:11.0: [1002:4390] type 0 class 0x000101 [ 0.179522] pci 0000:00:11.0: reg 10: [io 0x8000-0x8007] [ 0.179532] pci 0000:00:11.0: reg 14: [io 0x7000-0x7003] [ 0.179541] pci 0000:00:11.0: reg 18: [io 0x6000-0x6007] [ 0.179551] pci 0000:00:11.0: reg 1c: [io 0x5000-0x5003] [ 0.179560] pci 0000:00:11.0: reg 20: [io 0x3000-0x300f] [ 0.179570] pci 0000:00:11.0: reg 24: [mem 0xfe2ffc00-0xfe2fffff] [ 0.179591] pci 0000:00:11.0: set SATA to AHCI mode [ 0.179700] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03 [ 0.179714] pci 0000:00:12.0: reg 10: [mem 0xfe2fe000-0xfe2fefff] [ 0.179787] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03 [ 0.179806] pci 0000:00:12.2: reg 10: [mem 0xfe2ff800-0xfe2ff8ff] [ 0.179879] pci 0000:00:12.2: supports D1 D2 [ 0.179880] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.179884] pci 0000:00:12.2: PME# disabled [ 0.179905] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03 [ 0.179918] pci 0000:00:13.0: reg 10: [mem 0xfe2fd000-0xfe2fdfff] [ 0.179991] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03 [ 0.180010] pci 0000:00:13.2: reg 10: [mem 0xfe2ff400-0xfe2ff4ff] [ 0.180084] pci 0000:00:13.2: supports D1 D2 [ 0.180085] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.180088] pci 0000:00:13.2: PME# disabled [ 0.180109] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05 [ 0.180185] pci 0000:00:14.1: [1002:439c] type 0 class 0x000101 [ 0.180198] pci 0000:00:14.1: reg 10: [io 0x0000-0x0007] [ 0.180208] pci 0000:00:14.1: reg 14: [io 0x0000-0x0003] [ 0.180217] pci 0000:00:14.1: reg 18: [io 0x0000-0x0007] [ 0.180227] pci 0000:00:14.1: reg 1c: [io 0x0000-0x0003] [ 0.180237] pci 0000:00:14.1: reg 20: [io 0xff00-0xff0f] [ 0.180274] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403 [ 0.180296] pci 0000:00:14.2: reg 10: [mem 0xfe2f8000-0xfe2fbfff 64bit] [ 0.180341] pci 0000:00:14.2: Disabling memory decoding and releasing memory resources. [ 0.180435] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.180439] pci 0000:00:14.2: PME# disabled [ 0.180451] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601 [ 0.180529] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604 [ 0.180571] pci 0000:00:14.5: [1002:4399] type 0 class 0x000c03 [ 0.180584] pci 0000:00:14.5: reg 10: [mem 0xfe2fc000-0xfe2fcfff] [ 0.180657] pci 0000:00:15.0: [1002:43a0] type 1 class 0x000604 [ 0.180719] pci 0000:00:15.0: supports D1 D2 [ 0.180748] pci 0000:00:16.0: [1002:4397] type 0 class 0x000c03 [ 0.180762] pci 0000:00:16.0: reg 10: [mem 0xfe2f7000-0xfe2f7fff] [ 0.180835] pci 0000:00:16.2: [1002:4396] type 0 class 0x000c03 [ 0.180854] pci 0000:00:16.2: reg 10: [mem 0xfe2ff000-0xfe2ff0ff] [ 0.180927] pci 0000:00:16.2: supports D1 D2 [ 0.180928] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot [ 0.180932] pci 0000:00:16.2: PME# disabled [ 0.180953] pci 0000:00:18.0: [1022:1200] type 0 class 0x000600 [ 0.180985] pci 0000:00:18.1: [1022:1201] type 0 class 0x000600 [ 0.181010] pci 0000:00:18.2: [1022:1202] type 0 class 0x000600 [ 0.181037] pci 0000:00:18.3: [1022:1203] type 0 class 0x000600 [ 0.181068] pci 0000:00:18.4: [1022:1204] type 0 class 0x000600 [ 0.181134] pci 0000:01:05.0: [1002:9714] type 0 class 0x000300 [ 0.181147] pci 0000:01:05.0: reg 10: [mem 0xd0000000-0xdfffffff pref] [ 0.181153] pci 0000:01:05.0: reg 14: [io 0x9000-0x90ff] [ 0.181159] pci 0000:01:05.0: reg 18: [mem 0xfe4f0000-0xfe4fffff] [ 0.181175] pci 0000:01:05.0: reg 24: [mem 0xfe300000-0xfe3fffff] [ 0.181195] pci 0000:01:05.0: supports D1 D2 [ 0.181209] pci 0000:01:05.1: [1002:970f] type 0 class 0x000403 [ 0.181221] pci 0000:01:05.1: reg 10: [mem 0xfe4e8000-0xfe4ebfff] [ 0.181266] pci 0000:01:05.1: supports D1 D2 [ 0.181307] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.181391] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff] [ 0.181394] pci 0000:00:01.0: bridge window [mem 0xfe300000-0xfe4fffff] [ 0.181398] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.181449] pci 0000:02:00.0: [1000:0079] type 0 class 0x000104 [ 0.181461] pci 0000:02:00.0: reg 10: [io 0xa000-0xa0ff] [ 0.181474] pci 0000:02:00.0: reg 14: [mem 0xfe5fc000-0xfe5fffff 64bit] [ 0.181486] pci 0000:02:00.0: reg 1c: [mem 0xfe580000-0xfe5bffff 64bit] [ 0.181502] pci 0000:02:00.0: reg 30: [mem 0xfe540000-0xfe57ffff pref] [ 0.181528] pci 0000:02:00.0: supports D1 D2 [ 0.188063] pci 0000:00:02.0: PCI bridge to [bus 02-02] [ 0.188169] pci 0000:00:02.0: bridge window [io 0xa000-0xafff] [ 0.188172] pci 0000:00:02.0: bridge window [mem 0xfe500000-0xfe5fffff] [ 0.188176] pci 0000:00:02.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.188239] pci 0000:03:00.0: [104c:8231] type 1 class 0x000604 [ 0.188333] pci 0000:03:00.0: supports D1 D2 [ 0.188355] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.188442] pci 0000:00:04.0: PCI bridge to [bus 03-04] [ 0.188509] pci 0000:00:04.0: bridge window [io 0xf000-0x0000] (disabled) [ 0.188511] pci 0000:00:04.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.188516] pci 0000:00:04.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.188602] pci 0000:04:00.0: [1033:0035] type 0 class 0x000c03 [ 0.188627] pci 0000:04:00.0: reg 10: [mem 0xfe6ff000-0xfe6fffff] [ 0.188711] pci 0000:04:00.0: Disabling memory decoding and releasing memory resources. [ 0.188814] pci 0000:04:00.0: supports D1 D2 [ 0.188816] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot [ 0.188821] pci 0000:04:00.0: PME# disabled [ 0.188844] pci 0000:04:00.1: [1033:00e0] type 0 class 0x000c03 [ 0.188870] pci 0000:04:00.1: reg 10: [mem 0xfe6fec00-0xfe6fecff] [ 0.188953] pci 0000:04:00.1: Disabling memory decoding and releasing memory resources. [ 0.189038] pci 0000:04:00.1: Rounding up size of resource #0 to 0x1000. [ 0.189126] pci 0000:04:00.1: supports D1 D2 [ 0.189127] pci 0000:04:00.1: PME# supported from D0 D1 D2 D3hot [ 0.189132] pci 0000:04:00.1: PME# disabled [ 0.189166] pci 0000:04:01.0: [1033:00e7] type 0 class 0x000c00 [ 0.189192] pci 0000:04:01.0: reg 10: [mem 0xfe6fd000-0xfe6fdfff] [ 0.189275] pci 0000:04:01.0: Disabling memory decoding and releasing memory resources. [ 0.189393] pci 0000:04:01.0: supports D1 D2 [ 0.189394] pci 0000:04:01.0: PME# supported from D0 D1 D2 D3hot [ 0.189399] pci 0000:04:01.0: PME# disabled [ 0.189466] pci 0000:03:00.0: PCI bridge to [bus 04-04] [ 0.189543] pci 0000:03:00.0: bridge window [io 0xf000-0x0000] (disabled) [ 0.189548] pci 0000:03:00.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.189556] pci 0000:03:00.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.189621] pci 0000:05:00.0: [10ec:8168] type 0 class 0x000200 [ 0.189636] pci 0000:05:00.0: reg 10: [io 0xb800-0xb8ff] [ 0.189663] pci 0000:05:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit pref] [ 0.189680] pci 0000:05:00.0: reg 20: [mem 0xfdff8000-0xfdffbfff 64bit pref] [ 0.189691] pci 0000:05:00.0: reg 30: [mem 0xfe7e0000-0xfe7fffff pref] [ 0.189736] pci 0000:05:00.0: supports D1 D2 [ 0.189737] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.189741] pci 0000:05:00.0: PME# disabled [ 0.196066] pci 0000:00:05.0: PCI bridge to [bus 05-05] [ 0.196170] pci 0000:00:05.0: bridge window [io 0xb000-0xbfff] [ 0.196173] pci 0000:00:05.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.196177] pci 0000:00:05.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.196239] pci 0000:06:00.0: [1033:0194] type 0 class 0x000c03 [ 0.196265] pci 0000:06:00.0: reg 10: [mem 0xfe8fe000-0xfe8fffff 64bit] [ 0.196370] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold [ 0.196375] pci 0000:06:00.0: PME# disabled [ 0.204067] pci 0000:00:06.0: PCI bridge to [bus 06-06] [ 0.204170] pci 0000:00:06.0: bridge window [io 0xf000-0x0000] (disabled) [ 0.204173] pci 0000:00:06.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.204177] pci 0000:00:06.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.204217] pci 0000:07:05.0: [1186:4b01] type 0 class 0x000200 [ 0.204243] pci 0000:07:05.0: reg 10: [mem 0xfe9f8000-0xfe9fbfff] [ 0.204255] pci 0000:07:05.0: reg 14: [io 0xc800-0xc8ff] [ 0.204311] pci 0000:07:05.0: reg 30: [mem 0xfe9c0000-0xfe9dffff pref] [ 0.204344] pci 0000:07:05.0: supports D1 D2 [ 0.204345] pci 0000:07:05.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.204350] pci 0000:07:05.0: PME# disabled [ 0.204400] pci 0000:00:14.4: PCI bridge to [bus 07-07] (subtractive decode) [ 0.204474] pci 0000:00:14.4: bridge window [io 0xc000-0xcfff] [ 0.204478] pci 0000:00:14.4: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.204481] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.204483] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.204485] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.204486] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.204488] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode) [ 0.204490] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xdfffffff] (subtractive decode) [ 0.204491] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode) [ 0.204562] pci 0000:08:00.0: [197b:2368] type 0 class 0x000101 [ 0.204595] pci 0000:08:00.0: reg 10: [io 0xe800-0xe807] [ 0.204610] pci 0000:08:00.0: reg 14: [io 0xe400-0xe403] [ 0.204625] pci 0000:08:00.0: reg 18: [io 0xe000-0xe007] [ 0.204640] pci 0000:08:00.0: reg 1c: [io 0xd800-0xd803] [ 0.204655] pci 0000:08:00.0: reg 20: [io 0xd400-0xd40f] [ 0.204738] pci 0000:08:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.204850] pci 0000:00:15.0: PCI bridge to [bus 08-08] [ 0.204921] pci 0000:00:15.0: bridge window [io 0xd000-0xefff] [ 0.204925] pci 0000:00:15.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 0.204931] pci 0000:00:15.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.204959] pci_bus 0000:00: on NUMA node 0 [ 0.204963] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.205067] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.205093] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT] [ 0.205116] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT] [ 0.205144] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT] [ 0.205184] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT] [ 0.205218] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT] [ 0.205256] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE20._PRT] [ 0.210170] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 *11 14 15) [ 0.210674] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 *7 10 11 14 15) [ 0.211180] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 *10 11 14 15) [ 0.211681] ACPI: PCI Interrupt Link [LNKD] (IRQs *4 7 10 11 14 15) [ 0.212162] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 *10 11 14 15) [ 0.212632] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 14 15) *0 [ 0.213169] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 10 11 14 15) *0 [ 0.213742] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 14 15) *0 [ 0.214258] pci 0000:00:02.0: GSI18: level-low [ 0.214322] pci 0000:00:04.0: GSI16: level-low [ 0.214386] pci 0000:00:05.0: GSI17: level-low [ 0.214458] pci 0000:00:11.0: GSI19: level-low [ 0.214533] pci 0000:07:05.0: GSI20: level-low [ 0.214596] HEST: Table is not found! [ 0.214741] xen_mem: Initialising balloon driver. [ 0.215107] SCSI subsystem initialized [ 0.215194] libata version 3.00 loaded. [ 0.215194] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none [ 0.215194] vgaarb: loaded [ 0.215194] PCI: Using ACPI for IRQ routing [ 0.215194] PCI: pci_cache_line_size set to 64 bytes [ 0.215194] reserve RAM buffer: 000000000009e000 - 000000000009ffff [ 0.215194] reserve RAM buffer: 00000000cff90000 - 00000000cfffffff [ 0.215194] NetLabel: Initializing [ 0.215194] NetLabel: domain hash size = 128 [ 0.215194] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.215194] NetLabel: unlabeled traffic allowed by default [ 0.215194] Switching to clocksource xen [ 0.217020] AppArmor: AppArmor Filesystem Enabled [ 0.217100] pnp: PnP ACPI init [ 0.217193] ACPI: bus type pnp registered [ 0.217385] pnp 00:00: [bus 00-ff] [ 0.217387] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.217388] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.217390] pnp 00:00: [io 0x0d00-0xffff window] [ 0.217391] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.217393] pnp 00:00: [mem 0x000d0000-0x000dffff window] [ 0.217394] pnp 00:00: [mem 0xd0000000-0xdfffffff window] [ 0.217395] pnp 00:00: [mem 0xf0000000-0xfebfffff window] [ 0.217441] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 0.217546] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.217548] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.217594] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.217627] pnp 00:02: [dma 4] [ 0.217628] pnp 00:02: [io 0x0000-0x000f] [ 0.217630] pnp 00:02: [io 0x0081-0x0083] [ 0.217631] pnp 00:02: [io 0x0087] [ 0.217632] pnp 00:02: [io 0x0089-0x008b] [ 0.217633] pnp 00:02: [io 0x008f] [ 0.217634] pnp 00:02: [io 0x00c0-0x00df] [ 0.217654] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.217662] pnp 00:03: [io 0x0070-0x0071] [ 0.217669] pnp 00:03: [irq 8] [ 0.217687] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.217710] pnp 00:04: [io 0x0060] [ 0.217711] pnp 00:04: [io 0x0064] [ 0.217715] pnp 00:04: [irq 1] [ 0.217735] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.217775] pnp 00:05: [io 0x0061] [ 0.217792] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.217799] pnp 00:06: [io 0x00f0-0x00ff] [ 0.217802] pnp 00:06: [irq 13] [ 0.217820] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.218106] pnp 00:07: [io 0x0000-0xffffffffffffffff disabled] [ 0.218108] pnp 00:07: [io 0x0500-0x05df] [ 0.218109] pnp 00:07: [io 0x0ae0-0x0aef] [ 0.218141] pnp 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.218164] pnp 00:08: [mem 0xfed00000-0xfed003ff] [ 0.218182] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.218273] pnp 00:09: [mem 0xfec00000-0xfec00fff] [ 0.218274] pnp 00:09: [mem 0xfee00000-0xfee00fff] [ 0.218306] pnp 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.218467] pnp 00:0a: [io 0x0010-0x001f] [ 0.218469] pnp 00:0a: [io 0x0022-0x003f] [ 0.218470] pnp 00:0a: [io 0x0062-0x0063] [ 0.218471] pnp 00:0a: [io 0x0065-0x006f] [ 0.218472] pnp 00:0a: [io 0x0072-0x007f] [ 0.218473] pnp 00:0a: [io 0x0080] [ 0.218474] pnp 00:0a: [io 0x0084-0x0086] [ 0.218475] pnp 00:0a: [io 0x0088] [ 0.218476] pnp 00:0a: [io 0x008c-0x008e] [ 0.218477] pnp 00:0a: [io 0x0090-0x009f] [ 0.218478] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.218479] pnp 00:0a: [io 0x00b1] [ 0.218480] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.218481] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.218482] pnp 00:0a: [io 0x040b] [ 0.218483] pnp 00:0a: [io 0x04d6] [ 0.218484] pnp 00:0a: [io 0x0c00-0x0c01] [ 0.218485] pnp 00:0a: [io 0x0c14] [ 0.218486] pnp 00:0a: [io 0x0c50-0x0c51] [ 0.218487] pnp 00:0a: [io 0x0c52] [ 0.218488] pnp 00:0a: [io 0x0c6c] [ 0.218489] pnp 00:0a: [io 0x0c6f] [ 0.218491] pnp 00:0a: [io 0x0cd0-0x0cd1] [ 0.218492] pnp 00:0a: [io 0x0cd2-0x0cd3] [ 0.218493] pnp 00:0a: [io 0x0cd4-0x0cd5] [ 0.218494] pnp 00:0a: [io 0x0cd6-0x0cd7] [ 0.218495] pnp 00:0a: [io 0x0cd8-0x0cdf] [ 0.218496] pnp 00:0a: [io 0x0800-0x089f] [ 0.218498] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.218499] pnp 00:0a: [io 0x0b00-0x0b1f] [ 0.218500] pnp 00:0a: [io 0x0b20-0x0b3f] [ 0.218501] pnp 00:0a: [io 0x0900-0x090f] [ 0.218502] pnp 00:0a: [io 0x0910-0x091f] [ 0.218503] pnp 00:0a: [io 0xfe00-0xfefe] [ 0.218504] pnp 00:0a: [io 0x0060-0x005f disabled] [ 0.218505] pnp 00:0a: [io 0x0064-0x0063 disabled] [ 0.218507] pnp 00:0a: [mem 0xffb80000-0xffbfffff] [ 0.218508] pnp 00:0a: [mem 0xfec10000-0xfec1001f] [ 0.218509] pnp 00:0a: [mem 0xfed80000-0xfed80fff] [ 0.218510] pnp 00:0a: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.218584] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.218629] pnp 00:0b: [mem 0xe0000000-0xefffffff] [ 0.218661] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.224372] pnp 00:0c: [mem 0x00000000-0x0009ffff] [ 0.224374] pnp 00:0c: [mem 0x000c0000-0x000cffff] [ 0.224375] pnp 00:0c: [mem 0x000e0000-0x000fffff] [ 0.224377] pnp 00:0c: [mem 0x00100000-0xcfffffff] [ 0.224378] pnp 00:0c: [mem 0xfec00000-0xffffffff] [ 0.224430] pnp 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.224523] pnp: PnP ACPI: found 13 devices [ 0.224599] ACPI: ACPI bus type pnp unregistered [ 0.224669] system 00:07: [io 0x0500-0x05df] has been reserved [ 0.224741] system 00:07: [io 0x0ae0-0x0aef] has been reserved [ 0.224807] system 00:09: [mem 0xfec00000-0xfec00fff] has been reserved [ 0.224871] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.224936] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.225003] system 00:0a: [io 0x040b] has been reserved [ 0.225066] system 00:0a: [io 0x04d6] has been reserved [ 0.225133] system 00:0a: [io 0x0c00-0x0c01] has been reserved [ 0.225196] system 00:0a: [io 0x0c14] has been reserved [ 0.225259] system 00:0a: [io 0x0c50-0x0c51] has been reserved [ 0.225322] system 00:0a: [io 0x0c52] has been reserved [ 0.225386] system 00:0a: [io 0x0c6c] has been reserved [ 0.225448] system 00:0a: [io 0x0c6f] has been reserved [ 0.225510] system 00:0a: [io 0x0cd0-0x0cd1] has been reserved [ 0.225573] system 00:0a: [io 0x0cd2-0x0cd3] has been reserved [ 0.225636] system 00:0a: [io 0x0cd4-0x0cd5] has been reserved [ 0.225698] system 00:0a: [io 0x0cd6-0x0cd7] has been reserved [ 0.225761] system 00:0a: [io 0x0cd8-0x0cdf] has been reserved [ 0.225824] system 00:0a: [io 0x0800-0x089f] has been reserved [ 0.225887] system 00:0a: [io 0x0b00-0x0b1f] has been reserved [ 0.225950] system 00:0a: [io 0x0b20-0x0b3f] has been reserved [ 0.226020] system 00:0a: [io 0x0900-0x090f] has been reserved [ 0.226083] system 00:0a: [io 0x0910-0x091f] has been reserved [ 0.226145] system 00:0a: [io 0xfe00-0xfefe] has been reserved [ 0.226213] system 00:0a: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.226275] system 00:0a: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.226338] system 00:0a: [mem 0xfed80000-0xfed80fff] has been reserved [ 0.226404] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved [ 0.226469] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.226532] system 00:0c: [mem 0x000c0000-0x000cffff] has been reserved [ 0.226595] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.226658] system 00:0c: [mem 0x00100000-0xcfffffff] could not be reserved [ 0.226721] system 00:0c: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.227832] pci 0000:00:14.2: BAR 0: can't assign mem (size 0x4000) [ 0.227898] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.227962] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff] [ 0.228047] pci 0000:00:01.0: bridge window [mem 0xfe300000-0xfe4fffff] [ 0.228112] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.228192] pci 0000:00:02.0: PCI bridge to [bus 02-02] [ 0.228258] pci 0000:00:02.0: bridge window [io 0xa000-0xafff] [ 0.228323] pci 0000:00:02.0: bridge window [mem 0xfe500000-0xfe5fffff] [ 0.228387] pci 0000:00:02.0: bridge window [mem pref disabled] [ 0.228453] pci 0000:04:00.0: BAR 0: can't assign mem (size 0x1000) [ 0.228516] pci 0000:04:00.1: BAR 0: can't assign mem (size 0x1000) [ 0.228579] pci 0000:04:01.0: BAR 0: can't assign mem (size 0x1000) [ 0.228642] pci 0000:03:00.0: PCI bridge to [bus 04-04] [ 0.228705] pci 0000:03:00.0: bridge window [io disabled] [ 0.228772] pci 0000:03:00.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.228838] pci 0000:03:00.0: bridge window [mem pref disabled] [ 0.228907] pci 0000:00:04.0: PCI bridge to [bus 03-04] [ 0.228970] pci 0000:00:04.0: bridge window [io disabled] [ 0.229035] pci 0000:00:04.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.229099] pci 0000:00:04.0: bridge window [mem pref disabled] [ 0.229165] pci 0000:00:05.0: PCI bridge to [bus 05-05] [ 0.229229] pci 0000:00:05.0: bridge window [io 0xb000-0xbfff] [ 0.229294] pci 0000:00:05.0: bridge window [mem 0xfe700000-0xfe7fffff] [ 0.229359] pci 0000:00:05.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.229439] pci 0000:00:06.0: PCI bridge to [bus 06-06] [ 0.229893] pci 0000:00:06.0: bridge window [io disabled] [ 0.229958] pci 0000:00:06.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.230022] pci 0000:00:06.0: bridge window [mem pref disabled] [ 0.230088] pci 0000:00:14.4: PCI bridge to [bus 07-07] [ 0.230152] pci 0000:00:14.4: bridge window [io 0xc000-0xcfff] [ 0.230217] pci 0000:00:14.4: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.230282] pci 0000:00:14.4: bridge window [mem pref disabled] [ 0.230350] pci 0000:00:15.0: PCI bridge to [bus 08-08] [ 0.230414] pci 0000:00:15.0: bridge window [io 0xd000-0xefff] [ 0.230479] pci 0000:00:15.0: bridge window [mem disabled] [ 0.230543] pci 0000:00:15.0: bridge window [mem pref disabled] [ 0.230621] pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 0.230686] pci 0000:00:02.0: setting latency timer to 64 [ 0.230692] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.230756] pci 0000:00:04.0: setting latency timer to 64 [ 0.230765] pci 0000:03:00.0: setting latency timer to 64 [ 0.230771] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.230836] pci 0000:00:05.0: setting latency timer to 64 [ 0.230840] pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 0.230906] pci 0000:00:06.0: setting latency timer to 64 [ 0.230915] pci 0000:00:15.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.230980] pci 0000:00:15.0: setting latency timer to 64 [ 0.230982] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.230984] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.230985] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.230987] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff] [ 0.230988] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff] [ 0.230989] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff] [ 0.230991] pci_bus 0000:01: resource 0 [io 0x9000-0x9fff] [ 0.230992] pci_bus 0000:01: resource 1 [mem 0xfe300000-0xfe4fffff] [ 0.230993] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.230995] pci_bus 0000:02: resource 0 [io 0xa000-0xafff] [ 0.230996] pci_bus 0000:02: resource 1 [mem 0xfe500000-0xfe5fffff] [ 0.230998] pci_bus 0000:03: resource 1 [mem 0xfe600000-0xfe6fffff] [ 0.230999] pci_bus 0000:04: resource 1 [mem 0xfe600000-0xfe6fffff] [ 0.231000] pci_bus 0000:05: resource 0 [io 0xb000-0xbfff] [ 0.231002] pci_bus 0000:05: resource 1 [mem 0xfe700000-0xfe7fffff] [ 0.231003] pci_bus 0000:05: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.231005] pci_bus 0000:06: resource 1 [mem 0xfe800000-0xfe8fffff] [ 0.231006] pci_bus 0000:07: resource 0 [io 0xc000-0xcfff] [ 0.231007] pci_bus 0000:07: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.231009] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 0.231010] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 0.231011] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 0.231013] pci_bus 0000:07: resource 7 [mem 0x000d0000-0x000dffff] [ 0.231014] pci_bus 0000:07: resource 8 [mem 0xd0000000-0xdfffffff] [ 0.231015] pci_bus 0000:07: resource 9 [mem 0xf0000000-0xfebfffff] [ 0.231017] pci_bus 0000:08: resource 0 [io 0xd000-0xefff] [ 0.231218] NET: Registered protocol family 2 [ 0.231366] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.232240] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 0.233272] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.233561] TCP: Hash tables configured (established 262144 bind 65536) [ 0.233627] TCP reno registered [ 0.233691] UDP hash table entries: 4096 (order: 6, 262144 bytes) [ 0.233813] UDP-Lite hash table entries: 4096 (order: 6, 262144 bytes) [ 0.234138] NET: Registered protocol family 1 [ 0.234231] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled [ 0.332186] pci 0000:01:05.0: Boot video device [ 0.332216] pci 0000:03:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled [ 0.332400] PCI: CLS 64 bytes, default 64 [ 0.332436] Unpacking initramfs... [ 0.344331] Freeing initrd memory: 18520k freed [ 0.349122] MCE: bind virq for DOM0 logging [ 0.349168] MCE_DOM0_LOG: enter dom0 mce vIRQ handler [ 0.349170] MCE_DOM0_LOG: No more urgent data [ 0.349171] MCE_DOM0_LOG: No more nonurgent data [ 0.349352] audit: initializing netlink socket (disabled) [ 0.349435] type=2000 audit(1316696715.291:1): initialized [ 0.369747] VFS: Disk quotas dquot_6.5.2 [ 0.369900] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.370201] msgmni has been set to 3738 [ 0.370594] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.370719] io scheduler noop registered [ 0.370796] io scheduler deadline registered (default) [ 0.370922] io scheduler cfq registered [ 0.371387] pcieport 0000:00:02.0: ACPI _OSC control granted for 0x1d [ 0.371461] pcieport 0000:00:02.0: setting latency timer to 64 [ 0.371502] pcieport 0000:00:02.0: irq 727 (279) for MSI/MSI-X [ 0.371558] pcieport 0000:00:04.0: ACPI _OSC control granted for 0x1d [ 0.371629] pcieport 0000:00:04.0: setting latency timer to 64 [ 0.371664] pcieport 0000:00:04.0: irq 726 (278) for MSI/MSI-X [ 0.371716] pcieport 0000:00:05.0: ACPI _OSC control granted for 0x1d [ 0.371785] pcieport 0000:00:05.0: setting latency timer to 64 [ 0.371820] pcieport 0000:00:05.0: irq 725 (277) for MSI/MSI-X [ 0.371872] pcieport 0000:00:06.0: ACPI _OSC control granted for 0x1d [ 0.371942] pcieport 0000:00:06.0: setting latency timer to 64 [ 0.371977] pcieport 0000:00:06.0: irq 724 (276) for MSI/MSI-X [ 0.372049] pcieport 0000:00:15.0: ACPI _OSC control granted for 0x1d [ 0.372122] pcieport 0000:00:15.0: setting latency timer to 64 [ 0.372178] pcieport 0000:00:15.0: irq 723 (275) for MSI/MSI-X [ 0.372262] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 0.372327] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 0.372392] pcie_pme 0000:00:02.0:pcie01: service driver pcie_pme loaded [ 0.372404] pcieport 0000:00:04.0: Signaling PME through PCIe PME interrupt [ 0.372467] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt [ 0.372531] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 0.372595] pci 0000:04:00.1: Signaling PME through PCIe PME interrupt [ 0.372657] pci 0000:04:01.0: Signaling PME through PCIe PME interrupt [ 0.372722] pcie_pme 0000:00:04.0:pcie01: service driver pcie_pme loaded [ 0.372733] pcieport 0000:00:05.0: Signaling PME through PCIe PME interrupt [ 0.372797] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt [ 0.372861] pcie_pme 0000:00:05.0:pcie01: service driver pcie_pme loaded [ 0.372871] pcieport 0000:00:06.0: Signaling PME through PCIe PME interrupt [ 0.372935] pci 0000:06:00.0: Signaling PME through PCIe PME interrupt [ 0.372999] pcie_pme 0000:00:06.0:pcie01: service driver pcie_pme loaded [ 0.373015] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt [ 0.373078] pci 0000:08:00.0: Signaling PME through PCIe PME interrupt [ 0.373143] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded [ 0.373200] ERST: Table is not found! [ 0.373327] Non-volatile memory driver v1.3 [ 0.373390] Linux agpgart interface v0.103 [ 0.373796] Xen virtual console successfully installed as xvc0 [ 0.373979] ahci 0000:00:11.0: version 3.0 [ 0.373992] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.374120] ahci 0000:00:11.0: irq 722 (274) for MSI/MSI-X [ 0.374189] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 0.374277] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part [ 0.374984] scsi0 : ahci [ 0.375225] scsi1 : ahci [ 0.375390] scsi2 : ahci [ 0.375539] scsi3 : ahci [ 0.375692] ata1: SATA max UDMA/133 abar m1024@0xfe2ffc00 port 0xfe2ffd00 irq 722 [ 0.375779] ata2: SATA max UDMA/133 abar m1024@0xfe2ffc00 port 0xfe2ffd80 irq 722 [ 0.375857] ata3: SATA max UDMA/133 abar m1024@0xfe2ffc00 port 0xfe2ffe00 irq 722 [ 0.375935] ata4: SATA max UDMA/133 abar m1024@0xfe2ffc00 port 0xfe2ffe80 irq 722 [ 0.376087] Fixed MDIO Bus: probed [ 0.404170] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 0.404236] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 0.404437] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.404569] mice: PS/2 mouse device common for all mice [ 0.404736] rtc_cmos 00:03: RTC can wake from S4 [ 0.424180] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.424270] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 0.424586] TCP cubic registered [ 0.424761] NET: Registered protocol family 10 [ 0.425131] lo: Disabled Privacy Extensions [ 0.425374] Registering the dns_resolver key type [ 0.425536] libceph: loaded (mon/osd proto 15/24, osdmap 5/5 5/5) [ 0.425669] registered taskstats version 1 [ 0.426088] Magic number: 11:562:79 [ 0.426296] rtc_cmos 00:03: setting system clock to 2011-09-22 13:05:15 UTC (1316696715) [ 0.440730] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 0.696111] ata1: SATA link down (SStatus 0 SControl 300) [ 0.696241] ata3: SATA link down (SStatus 0 SControl 300) [ 0.696334] ata2: SATA link down (SStatus 0 SControl 300) [ 0.696422] ata4: SATA link down (SStatus 0 SControl 300) [ 0.696547] Freeing unused kernel memory: 392k freed [ 0.696718] Write protecting the kernel read-only data: 7984k [ 0.738009] megasas: 00.00.04.31-rc1 Mon. May 3, 11:41:51 PST 2010 [ 0.738099] megasas: 0x1000:0x0079:0x1000:0x9263: bus 2:slot 0:func 0 [ 0.738219] megaraid_sas 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 0.738300] megaraid_sas 0000:02:00.0: setting latency timer to 64 [ 0.738418] megasas: FW now in Ready state [ 0.748114] megasas_init_mfi: fw_support_ieee=0 [ 0.772302] scsi4 : LSI SAS based MegaRAID driver [ 0.779526] scsi 4:0:16:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.786186] scsi 4:0:17:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.793119] scsi 4:0:18:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.798222] scsi 4:0:19:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.805491] scsi 4:0:20:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.812380] scsi 4:0:21:0: Direct-Access ATA WDC WD2002FYPS-0 5G05 PQ: 0 ANSI: 5 [ 0.819208] scsi 4:0:23:0: Direct-Access ATA WDC WD2002FYPS-0 1G01 PQ: 0 ANSI: 5 [ 0.826611] scsi 4:2:0:0: Direct-Access LSI MR9261-8i 2.11 PQ: 0 ANSI: 5 [ 0.826843] sd 4:2:0:0: [sda] 19521474560 512-byte logical blocks: (9.99 TB/9.08 TiB) [ 0.826983] sd 4:2:0:0: [sda] Write Protect is off [ 0.827054] sd 4:2:0:0: [sda] Mode Sense: 1f 00 00 08 [ 0.827093] sd 4:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.852014] sda: sda1 sda2 sda3 [ 0.852426] sd 4:2:0:0: [sda] Attached SCSI disk [ 0.858719] pata_jmicron 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.858823] pata_jmicron 0000:08:00.0: setting latency timer to 64 [ 0.859115] scsi5 : pata_jmicron [ 0.859264] scsi6 : pata_jmicron [ 0.859768] ata5: PATA max UDMA/100 cmd 0xe800 ctl 0xe400 bmdma 0xd400 irq 16 [ 0.859842] ata6: PATA max UDMA/100 cmd 0xe000 ctl 0xd800 bmdma 0xd408 irq 16 [ 1.174676] pata_atiixp 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.174775] pata_atiixp 0000:00:14.1: setting latency timer to 64 [ 1.175054] scsi7 : pata_atiixp [ 1.175190] scsi8 : pata_atiixp [ 1.175326] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14 [ 1.175398] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15 [ 1.369133] pciback 0000:00:14.2: seizing device [ 1.369260] pciback 0000:04:00.0: seizing device [ 1.369329] pciback 0000:04:00.1: seizing device [ 1.369398] pciback 0000:04:01.0: seizing device [ 1.369539] pciback 0000:04:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.369610] pciback 0000:04:01.0: PCI INT A disabled [ 1.369705] pciback 0000:04:00.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.369773] pciback 0000:04:00.1: PCI INT A disabled [ 1.369880] pciback 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.369947] pciback 0000:04:00.0: PCI INT A disabled [ 1.370027] pciback 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.370093] pciback 0000:00:14.2: PCI INT A disabled [ 1.378332] netfront: Initialising virtual ethernet driver. [ 1.399850] device-mapper: uevent: version 1.0.3 [ 1.401831] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel(a)redhat.com [ 1.429691] udev[116]: starting version 166 [ 1.498360] [drm] Initialized drm 1.1.0 20060810 [ 1.529152] usbcore: registered new interface driver usbfs [ 1.529243] usbcore: registered new interface driver hub [ 1.529934] usbcore: registered new device driver usb [ 1.549074] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.549180] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.549379] ehci_hcd 0000:00:12.2: EHCI Host Controller [ 1.549483] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1 [ 1.550392] pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.550471] pci 0000:01:05.0: setting latency timer to 64 [ 1.550623] [drm] Initialized radeon 1.33.0 20080528 for 0000:01:05.0 on minor 0 [ 1.560286] ehci_hcd 0000:00:12.2: QUIRK: Enable exception for AMD Hudson ASPM [ 1.560375] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.562421] ehci_hcd 0000:00:12.2: debug port 1 [ 1.562525] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe2ff800 [ 1.572226] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.572418] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.572541] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.572682] usb usb1: Product: EHCI Host Controller [ 1.572802] usb usb1: Manufacturer: Linux 2.6.37.6-0.7-xen ehci_hcd [ 1.572923] usb usb1: SerialNumber: 0000:00:12.2 [ 1.573370] hub 1-0:1.0: USB hub found [ 1.573497] hub 1-0:1.0: 5 ports detected [ 1.573855] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.574910] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 1.575051] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2 [ 1.592167] ehci_hcd 0000:00:13.2: QUIRK: Enable exception for AMD Hudson ASPM [ 1.592266] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.592942] ehci_hcd 0000:00:13.2: debug port 1 [ 1.593032] ehci_hcd 0000:00:13.2: irq 17, io mem 0xfe2ff400 [ 1.604188] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.604312] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.604394] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.604495] usb usb2: Product: EHCI Host Controller [ 1.604578] usb usb2: Manufacturer: Linux 2.6.37.6-0.7-xen ehci_hcd [ 1.604662] usb usb2: SerialNumber: 0000:00:13.2 [ 1.604914] hub 2-0:1.0: USB hub found [ 1.605001] hub 2-0:1.0: 5 ports detected [ 1.605215] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.605931] ehci_hcd 0000:00:16.2: EHCI Host Controller [ 1.606029] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3 [ 1.628243] ehci_hcd 0000:00:16.2: QUIRK: Enable exception for AMD Hudson ASPM [ 1.628400] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.630957] ehci_hcd 0000:00:16.2: debug port 1 [ 1.631119] ehci_hcd 0000:00:16.2: irq 17, io mem 0xfe2ff000 [ 1.640210] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00 [ 1.640393] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.640520] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.640665] usb usb3: Product: EHCI Host Controller [ 1.640783] usb usb3: Manufacturer: Linux 2.6.37.6-0.7-xen ehci_hcd [ 1.640903] usb usb3: SerialNumber: 0000:00:16.2 [ 1.641323] hub 3-0:1.0: USB hub found [ 1.641451] hub 3-0:1.0: 4 ports detected [ 1.675883] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.675991] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.676632] ohci_hcd 0000:00:12.0: OHCI Host Controller [ 1.676710] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4 [ 1.701099] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfe2fe000 [ 1.760971] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.761108] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.761248] usb usb4: Product: OHCI Host Controller [ 1.761366] usb usb4: Manufacturer: Linux 2.6.37.6-0.7-xen ohci_hcd [ 1.761485] usb usb4: SerialNumber: 0000:00:12.0 [ 1.761917] hub 4-0:1.0: USB hub found [ 1.762044] hub 4-0:1.0: 5 ports detected [ 1.762378] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.762609] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 1.762751] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.801594] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe2fd000 [ 1.860215] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.860350] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.860490] usb usb5: Product: OHCI Host Controller [ 1.860608] usb usb5: Manufacturer: Linux 2.6.37.6-0.7-xen ohci_hcd [ 1.860728] usb usb5: SerialNumber: 0000:00:13.0 [ 1.861169] hub 5-0:1.0: USB hub found [ 1.861299] hub 5-0:1.0: 5 ports detected [ 1.861725] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 1.861919] ohci_hcd 0000:00:14.5: OHCI Host Controller [ 1.862067] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6 [ 1.888204] usb 1-1: new high speed USB device using ehci_hcd and address 2 [ 1.897512] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe2fc000 [ 1.956189] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.956322] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.956461] usb usb6: Product: OHCI Host Controller [ 1.956579] usb usb6: Manufacturer: Linux 2.6.37.6-0.7-xen ohci_hcd [ 1.956699] usb usb6: SerialNumber: 0000:00:14.5 [ 1.957124] hub 6-0:1.0: USB hub found [ 1.957250] hub 6-0:1.0: 2 ports detected [ 1.957567] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.957794] ohci_hcd 0000:00:16.0: OHCI Host Controller [ 1.957933] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7 [ 1.958402] ohci_hcd 0000:00:16.0: irq 18, io mem 0xfe2f7000 [ 2.016213] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.016347] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.016486] usb usb7: Product: OHCI Host Controller [ 2.016604] usb usb7: Manufacturer: Linux 2.6.37.6-0.7-xen ohci_hcd [ 2.016723] usb usb7: SerialNumber: 0000:00:16.0 [ 2.017159] hub 7-0:1.0: USB hub found [ 2.017287] hub 7-0:1.0: 4 ports detected [ 2.030516] usb 1-1: New USB device found, idVendor=14dd, idProduct=0002 [ 2.030655] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.030793] usb 1-1: Product: Multidevice [ 2.030930] usb 1-1: Manufacturer: Peppercon AG [ 2.031063] usb 1-1: SerialNumber: 222F2322FBBD05729544E5EE9340B4DF [ 2.067184] input: Peppercon AG Multidevice as /devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1:1.0/input/input1 [ 2.067353] generic-usb 0003:14DD:0002.0001: input,hidraw0: USB HID v1.01 Keyboard [Peppercon AG Multidevice] on usb-0000:00:12.2-1/input0 [ 2.070791] input: Peppercon AG Multidevice as /devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1:1.1/input/input2 [ 2.070969] generic-usb 0003:14DD:0002.0002: input,hidraw1: USB HID v1.01 Mouse [Peppercon AG Multidevice] on usb-0000:00:12.2-1/input1 [ 2.071062] usbcore: registered new interface driver usbhid [ 2.071126] usbhid: USB HID core driver [ 2.356224] usb 4-2: new low speed USB device using ohci_hcd and address 2 [ 2.492823] md: linear personality registered for level -1 [ 2.540288] usb 4-2: New USB device found, idVendor=0764, idProduct=0601 [ 2.540429] usb 4-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0 [ 2.540561] usb 4-2: Product: OR1500LCDRM1U [ 2.540680] usb 4-2: Manufacturer: CPS [ 2.670741] generic-usb 0003:0764:0601.0003: hiddev0,hidraw2: USB HID v1.10 Device [CPS OR1500LCDRM1U] on usb-0000:00:12.0-2/input0 [ 8.525288] kjournald starting. Commit interval 15 seconds [ 8.526801] EXT3-fs (dm-1): using internal journal [ 8.527161] EXT3-fs (dm-1): mounted filesystem with ordered data mode [ 9.206522] usb 4-2: USB disconnect, address 2 [ 10.517311] udev[512]: starting version 166 [ 10.601619] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 [ 10.601776] ACPI: Power Button [PWRB] [ 10.601897] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4 [ 10.602007] ACPI: Power Button [PWRF] [ 10.612743] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 10.617475] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 9602 ss_vid 1022 ss_did 9602 [ 10.617581] shpchp 0000:00:01.0: Cannot reserve MMIO region [ 10.617712] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 10.654917] sd 4:2:0:0: Attached scsi generic sg0 type 0 [ 10.659260] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 10.659389] r8169 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.659548] r8169 0000:05:00.0: setting latency timer to 64 [ 10.659615] r8169 0000:05:00.0: irq 721 (273) for MSI/MSI-X [ 10.660081] r8169 0000:05:00.0: eth0: RTL8168d/8111d at 0xffffc90011350000, 40:61:86:ea:f1:9e, XID 081000c0 IRQ 721 [ 10.674922] skge 0000:07:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 10.675071] skge: 1.13 addr 0xfe9f8000 irq 20 chip Yukon-Lite rev 9 [ 10.677910] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 10.684543] xhci_hcd 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 10.684682] xhci_hcd 0000:06:00.0: setting latency timer to 64 [ 10.684686] xhci_hcd 0000:06:00.0: xHCI Host Controller [ 10.684768] xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 8 [ 10.707002] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 10.733642] xhci_hcd 0000:06:00.0: irq 18, io mem 0xfe8fe000 [ 10.733760] skge 0000:07:05.0: eth1: addr 00:1b:11:10:8c:20 [ 10.733877] xhci_hcd 0000:06:00.0: irq 720 (272) for MSI/MSI-X [ 10.733919] xhci_hcd 0000:06:00.0: irq 719 (271) for MSI/MSI-X [ 10.733976] xhci_hcd 0000:06:00.0: irq 718 (270) for MSI/MSI-X [ 10.734014] xhci_hcd 0000:06:00.0: irq 717 (269) for MSI/MSI-X [ 10.734053] xhci_hcd 0000:06:00.0: irq 716 (268) for MSI/MSI-X [ 10.734091] xhci_hcd 0000:06:00.0: irq 715 (267) for MSI/MSI-X [ 10.734128] xhci_hcd 0000:06:00.0: irq 714 (266) for MSI/MSI-X [ 10.735690] usb usb8: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values [ 10.735785] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003 [ 10.735850] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.735930] usb usb8: Product: xHCI Host Controller [ 10.735994] usb usb8: Manufacturer: Linux 2.6.37.6-0.7-xen xhci_hcd [ 10.736073] usb usb8: SerialNumber: 0000:06:00.0 [ 10.736228] xHCI xhci_add_endpoint called for root hub [ 10.736230] xHCI xhci_check_bandwidth called for root hub [ 10.736255] hub 8-0:1.0: USB hub found [ 10.736322] hub 8-0:1.0: 4 ports detected [ 10.802271] HDA Intel 0000:01:05.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 10.802361] ALSA hda_intel.c:2398: Using LPIB position fix [ 10.803083] HDA Intel 0000:01:05.1: setting latency timer to 64 [ 10.817135] ALSA hda_intel.c:1488: Enable sync_write for stable communication [ 11.007737] usbcore: registered new interface driver usbback [ 11.066018] Event-channel device installed. [ 11.279450] Adding 4194300k swap on /dev/mapper/sys-swap. Priority:-1 extents:1 across:4194300k [ 11.688194] usb 4-2: new low speed USB device using ohci_hcd and address 3 [ 11.871320] usb 4-2: New USB device found, idVendor=0764, idProduct=0601 [ 11.871459] usb 4-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0 [ 11.871584] usb 4-2: Product: OR1500LCDRM1U [ 11.871701] usb 4-2: Manufacturer: CPS [ 12.014818] generic-usb 0003:0764:0601.0004: hiddev0,hidraw2: USB HID v1.10 Device [CPS OR1500LCDRM1U] on usb-0000:00:12.0-2/input0 [ 14.875850] kjournald starting. Commit interval 15 seconds [ 14.875982] EXT3-fs (dm-2): using internal journal [ 14.876219] EXT3-fs (dm-2): mounted filesystem with ordered data mode [ 14.878467] kjournald starting. Commit interval 15 seconds [ 14.878621] EXT3-fs (dm-3): using internal journal [ 14.878806] EXT3-fs (dm-3): mounted filesystem with ordered data mode [ 14.885917] kjournald starting. Commit interval 15 seconds [ 14.886050] EXT3-fs (dm-4): using internal journal [ 14.886235] EXT3-fs (dm-4): mounted filesystem with ordered data mode [ 14.944020] kjournald starting. Commit interval 15 seconds [ 14.945573] EXT3-fs (dm-5): using internal journal [ 14.945895] EXT3-fs (dm-5): mounted filesystem with ordered data mode [ 14.964210] kjournald starting. Commit interval 15 seconds [ 14.964466] EXT3-fs (sda1): using internal journal [ 14.964791] EXT3-fs (sda1): mounted filesystem with journal data mode [ 15.108271] EXT4-fs (dm-16): Ignoring delalloc option - requested data journaling mode [ 15.135771] EXT4-fs (dm-16): mounted filesystem with journalled data mode. Opts: data=journal,acl,user_xattr [ 17.895423] type=1400 audit(1316696732.964:2): apparmor="STATUS" operation="profile_load" name="/bin/ping" pid=1122 comm="apparmor_parser" [ 17.953985] type=1400 audit(1316696733.024:3): apparmor="STATUS" operation="profile_load" name="/sbin/klogd" pid=1127 comm="apparmor_parser" [ 18.061909] type=1400 audit(1316696733.132:4): apparmor="STATUS" operation="profile_load" name="/sbin/syslog-ng" pid=1131 comm="apparmor_parser" [ 18.162124] type=1400 audit(1316696733.232:5): apparmor="STATUS" operation="profile_load" name="/sbin/syslogd" pid=1135 comm="apparmor_parser" [ 18.348219] usb 4-2: USB disconnect, address 3 [ 18.515545] type=1400 audit(1316696733.584:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2" pid=1140 comm="apparmor_parser" [ 18.515612] type=1400 audit(1316696733.584:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//DEFAULT_URI" pid=1140 comm="apparmor_parser" [ 18.515652] type=1400 audit(1316696733.584:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//HANDLING_UNTRUSTED_INPUT" pid=1140 comm="apparmor_parser" [ 18.515714] type=1400 audit(1316696733.584:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//phpsysinfo" pid=1140 comm="apparmor_parser" [ 18.617132] type=1400 audit(1316696733.688:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/deliver" pid=1144 comm="apparmor_parser" [ 18.725049] type=1400 audit(1316696733.796:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/dovecot-auth" pid=1154 comm="apparmor_parser" [ 20.728995] microcode: Microcode Update Driver: v2.00-xen <tigran(a)aivazian.fsnet.co.uk>, Peter Oruba [ 20.829035] usb 4-2: new low speed USB device using ohci_hcd and address 4 [ 21.010004] usb 4-2: New USB device found, idVendor=0764, idProduct=0601 [ 21.010025] usb 4-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0 [ 21.010037] usb 4-2: Product: OR1500LCDRM1U [ 21.010046] usb 4-2: Manufacturer: CPS [ 21.035592] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 21.148976] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 21.149050] generic-usb 0003:0764:0601.0005: hiddev0,hidraw2: USB HID v1.10 Device [CPS OR1500LCDRM1U] on usb-0000:00:12.0-2/input0 [ 21.191597] ip_tables: (C) 2000-2006 Netfilter Core Team [ 22.378375] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found [ 27.190730] Bridge firewalling registered [ 27.217766] r8169 0000:05:00.0: eth0: link up [ 27.217784] r8169 0000:05:00.0: eth0: link up [ 27.224514] device eth0 entered promiscuous mode [ 27.240187] br0: port 1(eth0) entering forwarding state [ 27.240195] br0: port 1(eth0) entering forwarding state [ 28.082553] skge 0000:07:05.0: eth1: enabling interface [ 28.086484] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 28.091392] device eth1 entered promiscuous mode [ 29.769632] skge 0000:07:05.0: eth1: Link is up at 100 Mbps, full duplex, flow control both [ 29.771907] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 29.771941] br1: port 1(eth1) entering forwarding state [ 29.771941] br1: port 1(eth1) entering forwarding state [ 31.462386] megasas: fasync_helper was not called first [ 31.594899] Fusion MPT base driver 3.04.17 [ 31.594901] Copyright (c) 1999-2008 LSI Corporation [ 31.601143] Fusion MPT misc device (ioctl) driver 3.04.17 [ 31.601194] mptctl: Registered with Fusion MPT base driver [ 31.601196] mptctl: /dev/mptctl @ (major,minor=10,220) [ 31.737327] mpt2sas version 06.100.00.00 loaded [ 41.519534] megasas: fasync_helper was not called first -- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

2 5

[opensuse-virtual] PCI resource alignment command changed in 11.4? (non-page-aligned MMIO error)
by Shanti Kulkarni 22 Sep '11

22 Sep '11

I have a Dom0 which I upgraded from 11.2 (with OBS 4.0.2 Xen packages) to 11.4. One of my PVMs has a PCI card passed through. After the upgrade I am getting "non-page-aligned MMIO BAR" errors when attempting to launch that VM with the same kernel command line. Is there a different way to tell the kernel this information? I was passing a PCI USB/firewire card which had three PCI IDs: 04:00.0 (USB), 04:00.1 (USB 2), and 04:01.0 (firewire). Before upgrading, I could avoid that error and start the domain using the pci=resource_alignment kernel parameter in grub: module /vmlinuz-2.6.37.6-0.7-xen root=/dev/sys/root elevator=deadline swiotlb=force,256 iommu=soft pciback.permissive pciback.hide=(00:14.2)(04:00.0)(04:00.1)(04:01.0) pci=resource_alignment=00:14.2;04:00.0;04:00.1;04:01.0 radeon.modeset=0 vga=0x317 After upgrading, I this error when launching the PVM: "0000:04:00.1: non-page-aligned MMIO BAR found." I have tried changing the syntax of the resource_alignment command. I have also tried using other commands, such as reassigndev= and reassign_resources. I tried setting "(pci-passthrough-strict-check no)" in xend-config.sxp. Then the PVM launched, but oopsed when udev loaded. Has this command changed, or is it's syntax different? I'd appreciate any help you can provide. Here's some of the packages on my Dom0: kernel-xen-2.6.37.6-0.7.1.x86_64 kernel-xen-base-2.6.37.6-0.7.1.x86_64 kernel-xen-devel-2.6.37.6-0.7.1.x86_64 patterns-openSUSE-xen_server-11.4-6.9.1.x86_64 xen-4.0.2_52-0.2.1.x86_64 xen-doc-html-4.0.2_52-0.2.1.x86_64 xen-doc-pdf-4.0.2_52-0.2.1.x86_64 xen-libs-4.0.2_52-0.2.1.x86_64 xen-tools-4.0.2_52-0.2.1.x86_64 Thank you, Shanti-- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

1 0

[opensuse-virtual] DomU config for a Centos6 guest?
by gregk.xen＠mailforce.net 21 Sep '11

21 Sep '11

Hi, I've got no problems launching Opensuse DpmU Guests on top of my Opensuse Dom0. I need to install a Centos6 DomU guest now on the same box, using a .cfg file. For the initial installation, I just modified my cfg to be: name = 'install' builder = 'linux' bootloader = '/usr/lib/xen/boot/domUloader.py' bootargs = '--entry=xvda1:vmlinuz-xen,/boot/initrd-xen' disk = [ 'file:/home/gk/Downloads/CentOS-6.0-x86_64-minimal.iso,hdc:cdrom,r', 'phy:/dev/VG0/CentosLV,xvda,w'] ... but I've read that the domUloader.py is an Opensuse-specific bootloader? Is this the right .cfg for a Centos6 Domu? Greg -- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

2 17

[opensuse-virtual] Guest launches manually OK, not on System reboot when config is in /etc/xen/auto ?
by gregk.xen＠mailforce.net 19 Sep '11

19 Sep '11

Hi, I've gotten my 1st VM up & running on Opensuse 11.4 (both Dom0 & Guest) mostly the way I want it. I can bring it up/down manually from the shell command line with no problems, but starting from /etc/xen/auto isn't working. After system boot only the Dom0 is started, not the Guest. To troubleshoot I tried: service xendomains stop Shutting down Xen domains WARNING: xend is running! It is not recommended using libxenlight in conjunction with the legacy xend toolstack. Use -f (force) to override WARNING: xend is running! It is not recommended using libxenlight in conjunction with the legacy xend toolstack. Use -f (force) to override done service xendomains start Starting auto Xen domains mail.cfg: WARNING: xend is running! It is not recommended using libxenlight in conjunction with the legacy xend toolstack. Use -f (force) to override WARNING: xend is running! It is not recommended using libxenlight in conjunction with the legacy xend toolstack. Use -f (force) to override failed At this point there's no Guest launched: xm list Name ID Mem VCPUs State Time(s) Domain-0 0 1010 1 r----- 50.0 I 'tail -f /var/log/xen/*log /var/log/messages' to try to see more detail about what's happening at the 'service xendomains restart', but there's no output at all. I only get that feedback at the shell where I exec the command. Looking online I found this thread by <Jim Fehlig>: [openFATE 311112] libvirt driver for new xen toolstack http://lists.opensuse.org/opensuse-features/2011-03/msg00212.html Which talks about 'libxenlight' & 'legacy' stack on Opensuse. A bit over my head at this early stage :-/ I have these xen-related packages installed on the Host: rpm -qa | grep -i xen xen-tools-4.1.2_01-143.1.x86_64 kernel-xen-2.6.37.6-0.7.1.x86_64 xen-4.1.2_01-143.1.x86_64 kernel-xen-devel-2.6.37.6-0.7.1.x86_64 xen-kmp-default-4.1.2_01_k2.6.37.6_0.7-143.1.x86_64 xen-libs-4.1.2_01-143.1.x86_64 Is this all related to my not being able to auto-launch the Guest? Or is it something else? How can I get more, or any, debug information that's useful? Thanks, Greg -- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

2 3

[opensuse-virtual] Projects relationship
by Ciro Iriarte 13 Sep '11

13 Sep '11

Hi, anybody with more insight on this project can tell me if there's any relationship?, I know Ganeti and Opennebula overlaps, but not sure about the others.. Ganeti OpenNebula OpenVSwitch OpenStack Regards, -- Ciro Iriarte http://cyruspy.wordpress.com -- -- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

2 3

[opensuse-virtual] [Fwd: Malfunctioning bridge]
by Hans Witvliet 02 Sep '11

02 Sep '11

Hi all, In order to create a -more or less- representative test configuration, I tried to copy a real life situation into a xen-set-up: -external firewal (kc3040) -openvpn server (kc3072) -Internal firewall (kc3041) -management gateway (kc3075) -asterisk pabx -mysql server To simulate different networks, I created dummy ethernet devices, and connected bridges to it. All of the four bridges are working OK, except ONE: BR2 and also only from one virtual machine: openvpn/kc3072 If i ping on the vpn-box (vpn is not setup yet) towards internal firewall i see no traffic at all ( 172.16.100.1 => 172.16.100.2 ) Even if i do an tcpdump on the bridge-device from DOM-0, i dont see anything. On the otherhand, if i do a ping the otherway round (int-fw towards vpn) i see the icmp-request on the bridge device (but no repy, hence the problem) Looked at [internal] firewall, at the bridges, routing, but i'm clue-less…. Tried to move the whole configuration towards a different DOM-0, with the same result, rebuild the vpn-dom-U: still no show All firewall's are down. All boxes are suse: both firewals are open_11.4, mgnt+vpn are sles11sp1 and dom0 is also sles, but tried also with open. Tried the lists at xen, but the only replies were questions what i used to make the drawing ;-) Any suggestion where to look next? Kind regards, Hans Oh, btw config of the vpn-box (kc3072) is as follows: name="kc3072" description="int vpn server" uuid="99ee7c72-493b-e69d-3cfa-7b438fcd2988" memory=1000 maxmem=1000 vcpus=1 on_poweroff="destroy" on_reboot="restart" on_crash="destroy" localtime=0 keymap="en-us" builder="linux" bootloader="/usr/bin/pygrub" bootargs="" extra=" " disk=[ 'phy:/dev/xen-productie/kc3072-boot,xvda,w', 'phy:/dev/xen-productie/kc3072-swap,xvdb,w', 'phy:/dev/xen-productie/kc3072-syst,xvdc,w', 'phy:/dev/xen-productie/kc3072-data,xvdd,w', ] vif=[ 'mac=00:16:3e:30:72:01,bridge=br1', 'mac=00:16:3e:30:72:02,bridge=br2', 'mac=00:16:3e:30:72:03,bridge=br3', ] vfb=['type=vnc,vncunused=1'] kc3072:~ # ifconfig -a eth0 Link encap:Ethernet HWaddr 00:16:3E:30:72:01 inet addr:192.168.100.2 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe30:7201/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1140 (1.1 Kb) TX bytes:1530 (1.4 Kb) eth1 Link encap:Ethernet HWaddr 00:16:3E:30:72:02 inet addr:172.16.100.1 Bcast:172.16.100.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe30:7202/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:77 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:230 (230.0 b) TX bytes:3518 (3.4 Kb) eth2 Link encap:Ethernet HWaddr 00:16:3E:30:72:03 inet addr:192.168.0.236 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe30:7203/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:53 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2330 (2.2 Kb) TX bytes:872 (872.0 b)

2 5

[opensuse-virtual] OpenSuse 11.4 domU hang on boot
by David Gerbec 02 Sep '11

02 Sep '11

Hello Everyone! Been looking around the internet but have not found a solution for my problem yet, all i found was a report on opensuse forums with no replays. I have a Xen dom0 running on OpenSuse 11.4 x86_64, on this I’ve created 3 PV instances all running OpenSuse 11.4 x86_64 as well. All 3 PVs were installed the same way with the same package selection and only ONE of this 3 PVs hangs at booting time just before the login screen should appear. I looked at the log files of the VM, when it hangs and when it boots normally, i copied and compared the logs (boot.msg, messages, ...) but i am not able to find anything substantial. A work around this problem seems to be - destroy VM, start VM, and keep going until eventually the VM starts up correctly. For testing purposes I’ve installed a PV with OpenSuse 11.3 x86_64. This VM runs normally, boots OK every time. Any of you experienced anything like that? Any idea what else i could check? Any info / help would be much appreciated. Regards, David Gerbec -- David Gerbec, sistemska podpora Predlog! Obiščite prenovljeno spletno stran http://www.agenda.si ODPRTA KODA IN LINUX STORITVE : POSLOVNE RESITVE : UPRAVLJANJE IT : INFRASTRUKTURA IT : IZOBRAZEVANJE : PROGRAMSKA OPREMA Visit our updated web page at http://www.agenda.si OPEN SOURCE AND LINUX SERVICES : BUSINESS SOLUTIONS : IT MANAGEMENT : IT INFRASTRUCTURE : TRAINING : SOFTWARE "Windows is a 32-bit shell for a 16-bit extension to an 8-bit operating system designed for a 4-bit microprocessor by a 2-bit company that can't stand one bit of competition." -- To unsubscribe, e-mail: opensuse-virtual+unsubscribe(a)opensuse.org For additional commands, e-mail: opensuse-virtual+help(a)opensuse.org

2 3