die Installation ist nicht so trivial. Aber einfach kurz und schmerzlos mit
rpm -i --nodeps 1200ub...........rpm installieren
ok. - wenns nicht anders geht, dann halt mit Gewalt
Da du nicht den 1200Cu Plus hast sieht bei mir die Datei /proc/bus/usb/devices anders aus. [.....] da bei dir der Vendor und ProdID anders ist musst du dann auch, /sbin/modprobe scanner vendor=0x05d8 product=0x4002
is so weit klar
ebenfalls änderst du dann auch usbmgr.conf um.
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
das (none) bedeutet das für das Gerät kein Modul geladen ist.
und so lange wie da nicht 'scanner' geht nix - richtig?
Versuch ersteinmal die Installation des Treibers und dann ein Neustart, ohne Eintrag in /etc/init.d/boot.local aber mit dem Eintrag in usbmgr.conf. Wenns nicht klappt dann versuch den Eintrag in boot.local und melde mir eventuelle Fehlermeldungen beim Booten.
Versuche ausgeführt (leider nicht erfolgreich) Variante 1: ohne modprobe in boot.local boot.msg: ... <6>usb.c: registered new driver usbdevfs <6>usb.c: registered new driver hub <6>usb-uhci.c: $Revision: 1.259 $ time 00:53:43 May 16 2001 <6>usb-uhci.c: High bandwidth mode enabled <6>PCI: Found IRQ 5 for device 00:07.2 <6>PCI: The same IRQ used for device 00:07.3 <6>usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 5 <4>usb-uhci.c: Detected 2 ports <6>usb.c: new USB bus registered, assigned bus number 1 <6>hub.c: USB hub found <6>hub.c: 2 ports detected <6>PCI: Found IRQ 5 for device 00:07.3 <6>PCI: The same IRQ used for device 00:07.2 <6>usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 5 <4>usb-uhci.c: Detected 2 ports <6>usb.c: new USB bus registered, assigned bus number 2 <6>hub.c: USB hub found <6>hub.c: 2 ports detected <6>usb.c: registered new driver hid <6>mice: PS/2 mouse device common for all mice <4>fatfs: bogus cluster size <4>fatfs: bogus cluster size <6>hub.c: USB new device connect on bus1/1, assigned device number 2 <6>mouse0: PS/2 mouse device for input0 <6>input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb1:2.0 <6>hub.c: USB new device connect on bus1/2, assigned device number 3 <4>usb.c: USB device 3 (vend/prod 0x5d8/0x4002) is not claimed by any active driver. ... bei Variante 2 sieht das genau so aus, blos das einige Zeilen später diese Einträge zusätzlich da sind <6>usb.c: registered new driver usbscanner <6>scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product - 5d8:4002 <6>scanner.c: probe_scanner: Only two or three endpoints supported. <6>scanner.c: USB Scanner support registered. wie probier ich eigentlich am _einfachsten_ aus, ob der Scanner überhaupt angesprochen wird? -- tschau fisch