Hello again, i changed the card to an Adaptec Card AHA-2920 (96001-00 A) (the screen at the boot process tells me: Adaptec PCI) and now i have got two problems: 1. Windows 98 freezes, if the scanner isn't switched on at the boot process. After Windows completely loaded, i can switch off the scanner (strange, but i can arrange with that problem) 2. Under SuSE Linux 8.0 Yast2 tells me: there is no SCSI-Scanner and cdrecord -- scanbus shows no scsi-Card (it only shows the scsi - emulation of my dvd and cd- burner). On the left side Yast2 tells me at last: You have to install the scsi-Scanner manually.... and that i have to choose the scanner from the list ..... but there is no list with scanners or scsi-Cards.... This is at last the same message that i got while using the AdvanSys ABP 925. What have i to do, to install a scsi-card manually? (sorry, if it is maybe a stupid question, but i didn't find a manual to this problem). regards, Chris Am 18 Jul 2003 um 7:19 hat Vakvarju geschrieben:
On Thu, 17 Jul 2003 18:27:00 +0200 Christof Schmitt <christofschmitt@web.de> wrote:
Hello list,
just a time ago I had trouble with installing the SCSI-scanner HP ScanJet 4c and at last i thought, the SCSI Card is the troublemaker. So i got another SCSI Card (AdvanSys ABP 925) and a cable with SCSI 2 (i think) at one end and a end with a thick fifty pins adapter from a friend as a solution. But SuSE Hardware - List does not show ABP 925 (but it shows ABP 920 and 930). If i check cdrecord -scanbus, the SCSI Card is not there. The scanner and the SCSI Card works fine under Windows 98 SE. The automatical detection of the scanner doesn't work. What did i do wrong? The cable or the card?
regards,
I have experienced similar problems with the same type of scanner, but then I throw away the card and used an Adaptec PCI card... and it works.
VV
-- To unsubscribe send e-mail to suse-multimedia-e-unsubscribe@suse.com For additional commands send e-mail to suse-multimedia-e-help@suse.com
* christofschmitt@web.de <christofschmitt@web.de> [07-19-03 10:57]:
i changed the card to an Adaptec Card AHA-2920 (96001-00 A) (the screen at the boot process tells me: Adaptec PCI) and now i have got two problems:
[snip ... whinedohs problem ...]
- Under SuSE Linux 8.0 Yast2 tells me: there is no SCSI-Scanner and cdrecord -- scanbus shows no scsi-Card (it only shows the scsi - emulation of my dvd and cd- burner). On the left side Yast2 tells me at last: You have to install the scsi-Scanner manually.... and that i have to choose the scanner from the list ..... but there is no list with scanners or scsi-Cards....
This is at last the same message that i got while using the AdvanSys ABP 925. What have i to do, to install a scsi-card manually? (sorry, if it is maybe a stupid question, but i didn't find a manual to this problem).
As root run 'hwinfo --storage-ctrl' and post the results. You should get something similar to: 18: PCI 09.0: 0100 SCSI storage controller [Created at pci.65] Unique ID: WL76.urRinWvBqX1 Hardware Class: storage Model: "Adaptec AHA-2940U/UW/D / AIC-7881U" Vendor: pci 0x9004 "Adaptec" Device: pci 0x8178 "AHA-2940U/UW/D / AIC-7881U" I/O Ports: 0xcc00-0xccff (rw,disabled) Memory Range: 0xe6020000-??? (rw,non-prefetchable) Memory Range: 0xe4000000-??? (ro,disabled) IRQ: 9 (9308683 events) Driver Info #0: Driver Status: aic7xxx is active Driver Activation Cmd: "insmod aic7xxx" Driver Info #1: Driver Status: aic7xxx_old is not active Driver Activation Cmd: "insmod aic7xxx_old" Config Status: cfg=yes, avail=yes, need=no -- Patrick Shanahan Registered Linux User #207535 http://wahoo.no-ip.org @ http://counter.li.org
Thank you very much! I post the whole reaction of the command, although i know, the relevant part may be at 21 (cause i don't know, if there are conflicts by the other devices). # hwinfo --storage_ctrl 01: None 00.0: 0102 Floppy disk controller [Created at floppy.111] Unique ID: rdCR.3wRL2_g4d2B Hardware Class: storage Model: "Floppy disk controller" 16: PCI 07.1: 0101 IDE interface [Created at pci.65] Unique ID: ESW+.0uC65bt_EM6 Hardware Class: storage Model: "Advanced Micro Devices [AMD] AMD-756 [Viper] IDE" Vendor: 1022 "Advanced Micro Devices [AMD]" Device: 7409 "AMD-756 [Viper] IDE" Revision: 0x03 I/O Ports: 0xf000-0xf00f (rw) I/O Ports: 0x1f0-0x1f7 (rw) I/O Port: 0x3f6 (rw) I/O Ports: 0x170-0x177 (rw) I/O Port: 0x376 (rw) IRQ: 14 (9348 events) IRQ: 15 (64 events) 21: PCI 0c.0: 0100 SCSI storage controller [Created at pci.65] Unique ID: lgGW.9k2XT8OsphE Hardware Class: storage Model: "Future Domain TMC-18C30 [36C70]" Vendor: 1036 "Future Domain Corp." Device: 0000 "TMC-18C30 [36C70]" I/O Ports: 0xec00-??? (rw) Memory Range: 0xe2000000-??? (ro,disabled) IRQ: 11 (664 events) Driver Info #0: Driver Status: fdomain is not active Driver Activation Cmd: "insmod fdomain" 24: Parallel 00.0: 0100 SCSI storage controller [Created at parallel.245] Unique ID: ffnC.Zt53XuaRGT5 Hardware Class: storage Model: "Iomega PPA3" Vendor: s1800 "Iomega" Device: 0002 "PPA3" Device File: /dev/lp0 Driver Info #0: Driver Status: ppa is active Driver Activation Cmd: "modprobe ppa" Attached to: #11 (Parallel controller (SPP)) As i understand it: 01: floppy 16: mainboard? 21: the relevant part (or am i wrong? - there is no reference to 'Adaptec') I have seen some articles with Adaptec and fdomain or Future Domain (but SuSE 7.2) - but no solution to my problem. 24: my ZIP-device greetings, Chris Am Samstag, 19. Juli 2003 18:12 schrieb Patrick Shanahan:
- christofschmitt@web.de <christofschmitt@web.de> [07-19-03 10:57]:
i changed the card to an Adaptec Card AHA-2920 (96001-00 A) (the screen at the boot process tells me: Adaptec PCI) and now i have got two problems:
[snip ... whinedohs problem ...]
- Under SuSE Linux 8.0 Yast2 tells me: there is no SCSI-Scanner and cdrecord -- scanbus shows no scsi-Card (it only shows the scsi - emulation of my dvd and cd- burner). On the left side Yast2 tells me at last: You have to install the scsi-Scanner manually.... and that i have to choose the scanner from the list ..... but there is no list with scanners or scsi-Cards....
This is at last the same message that i got while using the AdvanSys ABP 925. What have i to do, to install a scsi-card manually? (sorry, if it is maybe a stupid question, but i didn't find a manual to this problem).
As root run 'hwinfo --storage-ctrl' and post the results.
You should get something similar to:
18: PCI 09.0: 0100 SCSI storage controller [Created at pci.65] Unique ID: WL76.urRinWvBqX1 Hardware Class: storage Model: "Adaptec AHA-2940U/UW/D / AIC-7881U" Vendor: pci 0x9004 "Adaptec" Device: pci 0x8178 "AHA-2940U/UW/D / AIC-7881U" I/O Ports: 0xcc00-0xccff (rw,disabled) Memory Range: 0xe6020000-??? (rw,non-prefetchable) Memory Range: 0xe4000000-??? (ro,disabled) IRQ: 9 (9308683 events) Driver Info #0: Driver Status: aic7xxx is active Driver Activation Cmd: "insmod aic7xxx" Driver Info #1: Driver Status: aic7xxx_old is not active Driver Activation Cmd: "insmod aic7xxx_old" Config Status: cfg=yes, avail=yes, need=no
* Christof Schmitt <christofschmitt@web.de> [07-19-03 12:29]:
Am Samstag, 19. Juli 2003 18:12 schrieb Patrick Shanahan:
- christofschmitt@web.de <christofschmitt@web.de> [07-19-03 10:57]: [snip ... various parts ...]
- Under SuSE Linux 8.0 Yast2 tells me: there is no SCSI-Scanner and cdrecord -- scanbus shows no scsi-Card (it only shows the scsi - emulation of my dvd and cd- burner). On the left side Yast2 tells me at last: You have to install the scsi-Scanner manually.... and that i have to choose the scanner from the list ..... but there is no list with scanners or scsi-Cards....
This is at last the same message that i got while using the AdvanSys ABP 925. What have i to do, to install a scsi-card manually? (sorry, if it is maybe a stupid question, but i didn't find a manual to this problem).
As root run 'hwinfo --storage-ctrl' and post the results.
You should get something similar to:
18: PCI 09.0: 0100 SCSI storage controller
IRQ: 9 (9308683 events) Driver Info #0: Driver Status: aic7xxx is active Driver Activation Cmd: "insmod aic7xxx"
Thank you very much! I post the whole reaction of the command, although i know, the relevant part may be at 21 (cause i don't know, if there are conflicts by the other devices).
# hwinfo --storage_ctrl
21: PCI 0c.0: 0100 SCSI storage controller
Driver Info #0: Driver Status: fdomain is not active Driver Activation Cmd: "insmod fdomain"
21: the relevant part (or am i wrong? - there is no reference to 'Adaptec') I have seen some articles with Adaptec and fdomain or Future Domain (but SuSE 7.2) - but no solution to my problem.
[top posting corrected, full quote trimmed ...]
From the line on 'Driver Status', it appears that the driver is ?_not active_?. I would search suse's sdb and google for the correct linux driver for the Adaptec 2920 card (?Future Domain?) and, if wrong, install the correct driver.
If you find that the driver is correct, then you need to search for information on how to make the driver _active_. Appears that linux sees the card but is not using it, therefore you cannot see a scanner, or anything else you might hang off that card. You might post in suse-linux-e and see if anyone else is using that card and what driver they use and/or how to make it active. Please post your results, gud luk, -- Patrick Shanahan Registered Linux User #207535 http://wahoo.no-ip.org @ http://counter.li.org
Hello I'm using suse 8.2 and 9. In both I have the problem that the microphone is always listening to the speakers, even when I have earphones and a separate microphone. Looking at the sound configuration through gnomemeeting the mic and the speakers are in /dev/dsp0 I'm guessing that they should be different devices, but I have no idea how to do that. Any suggestion? Thanks in advance Juan C. Gallardo
* Juan C. Gallardo <jgamo@cantv.net> [11-04-03 14:34]:
I'm using suse 8.2 and 9. In both I have the problem that the microphone is always listening to the speakers, even when I have earphones and a separate microphone.
Looking at the sound configuration through gnomemeeting the mic and the speakers are in /dev/dsp0 I'm guessing that they should be different devices, but I have no idea how to do that.
And the reason that you are posting this in the thread "SCSI/Scanner again" is ?? -- Patrick Shanahan Registered Linux User #207535 http://wahoo.no-ip.org @ http://counter.li.org
Dear All! I have Suse 7.1 on CD rom. This work correctly from CD (I had some succesfully screen changes some days ago thanx for You), but now I would like to install on my hard drive. I don't know how begin this work. Thanx: Janek __________________________________ Do you Yahoo!? Protect your identity with Yahoo! Mail AddressGuard http://antispam.yahoo.com/whatsnewfree
Not sure what you are asking for, please be specific. I can say that newer versions work better on older hardware. I started with SuSE 7.2 as my first version to load and it has just gotten easier with each new version. Also, does this have anything to do with multimedia? :) JF *********** REPLY SEPARATOR *********** On 11/6/2003 at 9:24 AM Janek wrote:
Dear All!
I have Suse 7.1 on CD rom. This work correctly from CD (I had some succesfully screen changes some days ago thanx for You), but now I would like to install on my hard drive.
I don't know how begin this work.
Thanx: Janek
participants (6)
-
Christof Schmitt -
christofschmitt＠web.de
-
Janek -
John Fields -
Juan C. Gallardo -
Patrick Shanahan