Re: [suse-multimedia-e] SCSI/Scanner again

19 Jul 2003

      Thank you very much! I post the whole reaction of the command, although i  
know, the relevant part may be at 21 (cause i don't know, if there are 
conflicts by the other devices).

# hwinfo --storage_ctrl
01: None 00.0: 0102 Floppy disk controller
  [Created at floppy.111]
  Unique ID: rdCR.3wRL2_g4d2B
  Hardware Class: storage
  Model: "Floppy disk controller"

16: PCI 07.1: 0101 IDE interface
  [Created at pci.65]
  Unique ID: ESW+.0uC65bt_EM6
  Hardware Class: storage
  Model: "Advanced Micro Devices [AMD] AMD-756 [Viper] IDE"
  Vendor: 1022 "Advanced Micro Devices [AMD]"
  Device: 7409 "AMD-756 [Viper] IDE"
  Revision: 0x03
  I/O Ports: 0xf000-0xf00f (rw)
  I/O Ports: 0x1f0-0x1f7 (rw)
  I/O Port: 0x3f6 (rw)
  I/O Ports: 0x170-0x177 (rw)
  I/O Port: 0x376 (rw)
  IRQ: 14 (9348 events)
  IRQ: 15 (64 events)

21: PCI 0c.0: 0100 SCSI storage controller
  [Created at pci.65]
  Unique ID: lgGW.9k2XT8OsphE
  Hardware Class: storage
  Model: "Future Domain TMC-18C30 [36C70]"
  Vendor: 1036 "Future Domain Corp."
  Device: 0000 "TMC-18C30 [36C70]"
  I/O Ports: 0xec00-??? (rw)
  Memory Range: 0xe2000000-??? (ro,disabled)
  IRQ: 11 (664 events)
  Driver Info #0:
    Driver Status: fdomain is not active
    Driver Activation Cmd: "insmod fdomain"

24: Parallel 00.0: 0100 SCSI storage controller
  [Created at parallel.245]
  Unique ID: ffnC.Zt53XuaRGT5
  Hardware Class: storage
  Model: "Iomega PPA3"
  Vendor: s1800 "Iomega"
  Device: 0002 "PPA3"
  Device File: /dev/lp0
  Driver Info #0:
    Driver Status: ppa is active
    Driver Activation Cmd: "modprobe ppa"
  Attached to: #11 (Parallel controller (SPP))

As i understand it:
01: floppy
16: mainboard?
21: the relevant part (or am i wrong? - there is no reference to 'Adaptec')
I have seen some articles with Adaptec and fdomain or Future Domain (but SuSE 
7.2) - but no solution to my problem.
24: my ZIP-device

greetings,

Chris

Am Samstag, 19. Juli 2003 18:12 schrieb Patrick Shanahan:
...
* christofschmitt@web.de  [07-19-03 10:57]:
...
i changed the card to an Adaptec Card AHA-2920 (96001-00 A) (the
screen at the boot process tells me: Adaptec PCI) and now i have got
two problems:
[snip ... whinedohs problem ...]
...
2. Under SuSE Linux 8.0 Yast2 tells me: there is no SCSI-Scanner and
cdrecord -- scanbus shows no scsi-Card (it only shows the scsi -
emulation of my dvd and cd- burner). On the left side Yast2 tells me
at last: You have to install the scsi-Scanner manually.... and that i
have to choose the scanner from the list ..... but there is no list
with scanners or scsi-Cards....
This is at last the same message that i got while using the AdvanSys
ABP 925. What have i to do, to install a scsi-card manually? (sorry,
if it is maybe a stupid question, but i didn't find a manual to this
problem).
As root run 'hwinfo --storage-ctrl' and post the results.
You should get something similar to:
18: PCI 09.0: 0100 SCSI storage controller
  [Created at pci.65]
  Unique ID: WL76.urRinWvBqX1
  Hardware Class: storage
  Model: "Adaptec AHA-2940U/UW/D / AIC-7881U"
  Vendor: pci 0x9004 "Adaptec"
  Device: pci 0x8178 "AHA-2940U/UW/D / AIC-7881U"
  I/O Ports: 0xcc00-0xccff (rw,disabled)
  Memory Range: 0xe6020000-??? (rw,non-prefetchable)
  Memory Range: 0xe4000000-??? (ro,disabled)
  IRQ: 9 (9308683 events)
  Driver Info #0:
    Driver Status: aic7xxx is active
    Driver Activation Cmd: "insmod aic7xxx"
  Driver Info #1:
    Driver Status: aic7xxx_old is not active
    Driver Activation Cmd: "insmod aic7xxx_old"
  Config Status: cfg=yes, avail=yes, need=no

Re: [suse-multimedia-e] SCSI/Scanner again

Christof Schmitt