Hallo Karsten
Erzeuge ein /etc/isapnp.conf File und stelle dort die richtigen Werte ein.
pnpdump > /etc/isapnp.conf
ich schaffs nicht :-( ich hab die mit >>>> markierte Zeile dazugeschrieben mit isapnp zurückgescrieben cuba1:~ #rcisdn stop cuba1:~ # rcisdn start Setting up ISDN card contr0 Teles 16.3c done Loading Driver contr0 hisax-: No such device done und in /var/log/messages steht immer noch: Dec 6 19:51:10 cuba1 kernel: HFCS: resetting card Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ 5 count 0 Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ 5 count 0 Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ(5) getting no interrupts during init 1 Dec 6 19:51:10 cuba1 kernel: HFCS: resetting card Dec 6 19:51:10 cuba1 kernel: bug: kernel timer added twice at c46ad134. Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ 5 count 0 Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ(5) getting no interrupts during init 2 Dec 6 19:51:10 cuba1 kernel: HFCS: resetting card Dec 6 19:51:10 cuba1 kernel: bug: kernel timer added twice at c46ad134. Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ 5 count 0 Dec 6 19:51:10 cuba1 kernel: Teles 16.3c: IRQ(5) getting no interrupts during init 3 was genau sollte ich in /etc/isapnp.conf einstellen? # $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $ # Release isapnptools-1.26 # # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of the output file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE _NANOSLEEP -DWANT_TO_VALIDATE # # Trying port address 0273 # Board 1 has serial identifier 82 43 dc 2e 69 10 26 27 50 # (DEBUG) (READPORT 0x0273) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING # Card 1: (serial identifier 82 43 dc 2e 69 10 26 27 50) # Vendor Id TAG2610, Serial Number 1138503273, checksum 0x82. # Version 1.0, Vendor version 1.1 # ANSI string -->TELES.S0/16.3c Plug&Play<-- # # Logical device id TAG2610 # Device supports I/O range check register # Device supports vendor reserved register @ 0x39 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3c # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE TAG2610/1138503273 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0580 # Maximum IO base address 0x05bc # IO base alignment 4 bytes # Number of IO addresses required: 2 # (IO 0 (SIZE 2) (BASE 0x0580) (CHECK)) # IRQ 3, 4, 5, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E)))
(INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0500 # Maximum IO base address 0x05bc # IO base alignment 4 bytes # Number of IO addresses required: 2 # (IO 0 (SIZE 2) (BASE 0x0500) (CHECK)) # IRQ 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0680 # Maximum IO base address 0x06bc # IO base alignment 4 bytes # Number of IO addresses required: 2 # (IO 0 (SIZE 2) (BASE 0x0680) (CHECK)) # IRQ 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Start dependent functions: priority functional # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x1500 # Maximum IO base address 0x17fc # IO base alignment 4 bytes # Number of IO addresses required: 2 # (IO 0 (SIZE 2) (BASE 0x1500) (CHECK)) # IRQ 3, 4, 5, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # End dependent functions # Vendor defined tag: 84 a1 32 36 31 30 38 31 31 38 31 31 37 33 37 32 # Vendor defined tag: 84 a2 54 45 4c 45 53 (NAME "TAG2610/1138503273[0]{TELES.S0/16.3c Plug&Play}") # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY) mit freundlichen Grüßen Michael Temeschinko