[S.u.S.E. Linux] 3COM 3c905B
![](https://seccdn.libravatar.org/avatar/4e11b2c6265471f9dbbf20052b8662ee.jpg?s=120&d=mm&r=g)
Greeetings from CT, USA. I am attempting to configure a new server; Pentium II 266 w/ 64 MB RAM, adaptec SCSI and 3COM 3c905BTX (Cyclone) NIC. Everything is working fine *except* the network interface card. The driver appears to load properly; ie. reports all the NIC info such as irq, i/o base, MAC address, etc. but the card appears to be "dead". Activity light won't flash and pings don't seem to make it onto the wire. An "arp -a" shows no entries. I've used the 3COM setup disk to run most of the card diagnostics and they all pass. I've also tried disabling full/half duplex auto-detect. There are no options set in /etc/conf.modules for this particular card. Any ideas ??? Thanks in advance, Reiney / B. Reiney Brown - Summit Communications \ \ 860.456.9120 reiney@sumcom.net / -- To get out of this list, please send email to majordomo@suse.com with this text in its body: unsubscribe suse-linux-e
![](https://seccdn.libravatar.org/avatar/0fc3cf100f9597bb0229052d420bc5a9.jpg?s=120&d=mm&r=g)
At 12:55 98/06/23 -0400, you wrote:
Greeetings from CT, USA. I am attempting to configure a new server; Pentium II 266 w/ 64 MB RAM, adaptec SCSI and 3COM 3c905BTX (Cyclone) NIC. Everything is working fine *except* the network interface card. The driver appears to load properly; ie. reports all the NIC info such as irq, i/o base, MAC address, etc. but the card appears to be "dead". Activity light won't flash and pings don't seem to make it onto the wire. An "arp -a" shows no entries. I've used the 3COM setup disk to run most of the card diagnostics and they all pass. I've also tried disabling full/half duplex auto-detect. There are no options set in /etc/conf.modules for this particular card. Any ideas ???
Thanks in advance,
Reiney
Try to get the latest drivers for your card from <A HREF="http://cesdis.gsfc.nasa.gov/linux/drivers/"><A HREF="http://cesdis.gsfc.nasa.gov/linux/drivers/</A">http://cesdis.gsfc.nasa.gov/linux/drivers/. BTW, the site also carries hints for the various NICs. HTH Arun Khan -- To get out of this list, please send email to majordomo@suse.com with this text in its body: unsubscribe suse-linux-e
![](https://seccdn.libravatar.org/avatar/c22e8f5951950694f60a9e451d2e13c7.jpg?s=120&d=mm&r=g)
Reiney Brown wrote:
Greeetings from CT, USA. I am attempting to configure a new server; Pentium II 266 w/ 64 MB RAM, adaptec SCSI and 3COM 3c905BTX (Cyclone) NIC. Everything is working fine *except* the network interface card. The driver appears to load properly; ie. reports all the NIC info such as irq, i/o base, MAC address, etc. but the card appears to be "dead".
I'd bet its DOA, try another card. We've had a bad bunch of the 3COM cards here lately also. Dana -- To get out of this list, please send email to majordomo@suse.com with this text in its body: unsubscribe suse-linux-e
participants (3)
-
arunkhan@xnet.com
-
dana@ntd.net
-
reiney@sumcom.net