[opensuse] xen install problem of 10.3 beta 3 on 10.2 system
I downloaded the 10.3 x86_64bit dvd and was going to add a new domU on my 10.2 system but nothing seems to work. I have a OpenSuse 10.2 x86_64 AMD AM2 system running xen. Installing 10.2 domU works ok when done over network or iso image but I can't even get the install to start when trying 10.3 beta 3. Network install: I loopback mount the .iso on a different system and export it. I set the custom installation source url to point to it and hit next Popup that no kernel found Mount the same nfs on dom0 and can see /mnt/boot/x86_64/vmlinuz-xen test the same thing with 10.2 dvd and that works. ISO: set iso install path to openSUSE-10.3-Beta3-DVD-x86_64.iso after a few pop-up windows I get the same kernel error as on network but can't cancel out of it properly, have to start "yast2 xen" all over copying {vmlinuz,initrd]-xen from image somewhere else and use them as a non-suse install it starts up and I get a window where the boot up gets going but then it hangs. Besides the installation source everything else is left at defaults What am I doing wrong ?(hope it's not expecting to much) I would expect installing a 10.3 domU on a 10.2 system would be a common thing so if it's a bug I expect it to be some noise about it. What can I do to install a 10.3 domU ? /ps The end of the install that hangs shows: PNP: No PS/2 controller found. Probing ports directly. i8042.c: No controller found. mice: PS/2 mouse device common for all mice NET: Registered protocol family 1 XENBUS: Device with no driver: device/vbd/768 XENBUS: Device with no driver: device/vbd/832 XENBUS: Device with no driver: device/vif/0 Freeing unused kernel memory: 188k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx/öps SCSI subsystem initialized st: Version 20070203, fixed bufsize 32768, s/g segs 256 BIOS EDD facility v0.16 2004-Jun-25, 0 devices found EDD information not available. NET: Registered protocol family 17 loop: module loaded xen-vbd: registered block device major 3 blkfront: hda: barriers enabled hda: unknown partition table blkfront: hdb: barriers enabled hdb: unknown partition table netfront: Initialising virtual ethernet driver. netfront: device eth0 has flipping receive path. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Can I assume that installing OpenSuSE 10.3 Beta 3 64bit as a domU on a openSuse 10.2 works just fine for everyone out there ? I still can't even do a test install of it. On Sat, 2007-09-08 at 04:18 -0400, Peter Sjoberg wrote:
I downloaded the 10.3 x86_64bit dvd and was going to add a new domU on my 10.2 system but nothing seems to work.
I have a OpenSuse 10.2 x86_64 AMD AM2 system running xen. Installing 10.2 domU works ok when done over network or iso image but I can't even get the install to start when trying 10.3 beta 3.
Network install: I loopback mount the .iso on a different system and export it. I set the custom installation source url to point to it and hit next Popup that no kernel found Mount the same nfs on dom0 and can see /mnt/boot/x86_64/vmlinuz-xen test the same thing with 10.2 dvd and that works.
ISO: set iso install path to openSUSE-10.3-Beta3-DVD-x86_64.iso after a few pop-up windows I get the same kernel error as on network but can't cancel out of it properly, have to start "yast2 xen" all over copying {vmlinuz,initrd]-xen from image somewhere else and use them as a non-suse install it starts up and I get a window where the boot up gets going but then it hangs.
Besides the installation source everything else is left at defaults
What am I doing wrong ?(hope it's not expecting to much) I would expect installing a 10.3 domU on a 10.2 system would be a common thing so if it's a bug I expect it to be some noise about it. What can I do to install a 10.3 domU ?
/ps
The end of the install that hangs shows:
PNP: No PS/2 controller found. Probing ports directly. i8042.c: No controller found. mice: PS/2 mouse device common for all mice NET: Registered protocol family 1 XENBUS: Device with no driver: device/vbd/768 XENBUS: Device with no driver: device/vbd/832 XENBUS: Device with no driver: device/vif/0 Freeing unused kernel memory: 188k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx/öps SCSI subsystem initialized st: Version 20070203, fixed bufsize 32768, s/g segs 256 BIOS EDD facility v0.16 2004-Jun-25, 0 devices found EDD information not available. NET: Registered protocol family 17 loop: module loaded xen-vbd: registered block device major 3 blkfront: hda: barriers enabled hda: unknown partition table blkfront: hdb: barriers enabled hdb: unknown partition table netfront: Initialising virtual ethernet driver. netfront: device eth0 has flipping receive path. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
participants (1)
-
Peter Sjoberg