Re: [opensuse] openSuSE 10.2 crashing too often
I have superkaramba installed and already use some plugins (the almost omnipresent LiquidWeather and some others).
None of the plugins for monitoring will display the info I need (CPU temp, HDD rpm's, etc) even after executing sensors-detect as root and getting some "Succeed!" messages for some sensors...
Any ideas on this?
Thanks,
Martin
----- Original Message ----
From: Clayton
is there any way to check the temperature and watch the r.p.m. on the fans w/o going to BIOS-level?
lm-sensors works well for this. Once you ran sensors-detect you can use lots of different tools to view the fan rpm/core temps etc. (KSensors, gkrelm, SuperKaramba and pretty much any monitoring plugin, etc etc). C. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
I have superkaramba installed and already use some plugins (the almost omnipresent LiquidWeather and some others). None of the plugins for monitoring will display the info I need (CPU temp, HDD rpm's, etc) even after executing sensors-detect as root and getting some "Succeed!" messages for some sensors...
Any ideas on this?
Did you do the modprobes? If you haven't done them manually either by entering each line or by executing your init scripts (for example on boot) then the kernel modules have not been loaded... only identified by sensors-detect. C. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Martin Mielke wrote:
I have superkaramba installed and already use some plugins (the almost omnipresent LiquidWeather and some others). None of the plugins for monitoring will display the info I need (CPU temp, HDD rpm's, etc) even after executing sensors-detect as root and getting some "Succeed!" messages for some sensors...
Any ideas on this?
Maybe your motherboard/bios does not deliver the relevant data? I frequently experience this with cheapo boards where the manafacturers restricted the bios in this respect. Did you follow exactly the advice that sensors-detect gave you? This is especially important in regard to execute the given "modprobe xxx" commands before running "sensors", otherwise it will not work. What is the output, if you run "sensors" from the commandline? ex. on my system this reads like this: ###start of sensors output### w83627thf-isa-0290 Adapter: ISA adapter VCore: +1.60 V (min = +0.00 V, max = +3.84 V) +12V: +12.28 V (min = +7.78 V, max = +0.00 V) ALARM +3.3V: +3.36 V (min = +0.42 V, max = +0.74 V) ALARM +5V: +5.04 V (min = +3.65 V, max = +4.56 V) ALARM -12V: +6.06 V (min = +0.14 V, max = -12.20 V) ALARM V5SB: +5.08 V (min = +0.97 V, max = +1.02 V) ALARM VBat: +0.16 V (min = +2.56 V, max = +1.17 V) ALARM fan1: 0 RPM (min = -1 RPM, div = 128) ALARM CPU Fan: 2872 RPM (min = -1 RPM, div = 2) ALARM fan3: 0 RPM (min = 292 RPM, div = 128) ALARM M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor vid: +1.525 V (VRM Version 9.0) alarms: beep_enable: ### end of sensors output ### only after you get some relevant output from "sensors" on the commandline I would recommend you to look into graphical frontends to read the data in a more friendly way. regards Eberhard -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
###start of sensors output### [snip] temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor [snip]
-48.0°C ?? Wow, that's impressive :-) C . -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Clayton wrote:
###start of sensors output### [snip] temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor [snip]
-48.0°C ?? Wow, that's impressive :-)
He put in a bigger fan. ;-) -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
James Knott wrote:
Clayton wrote:
###start of sensors output### [snip] temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor [snip]
-48.0°C ?? Wow, that's impressive :-)
He put in a bigger fan. ;-)
You know there is nothing but good cooling ;-). Actually it is even better. When the CPU is used heavily anything goes up, but this special sensor stays at -48.0°C. As this sensor works so reliably stable and constantly cool, I decided that there is no need for me to display it with ksensors ;-)) regards Eberhard -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Eberhard Roloff wrote:
What is the output, if you run "sensors" from the commandline? ex. on my system this reads like this:
M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor
I don't know if I would trust these temperature measurements. A CPU with 25.5°C is highly unusable; normally they are much hotter. Joachim -- =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Joachim Schrod Email: jschrod@acm.org Roedermark, Germany -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor
I don't know if I would trust these temperature measurements. A CPU with 25.5°C is highly unusable; normally they are much hotter.
Really? I dunno... my AMD X2 3800+ runs at idle between 30°C and 32°C. Under load it can sometimes reach 42°C to 45°C (if both cores are at 100%). What helps is that I have a very good quality heatsink and massive (low noise) fan for cooling. A friend runs his system with water cooling and at idle, the CPUs are about 25°C. C. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Clayton wrote:
M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor
I don't know if I would trust these temperature measurements. A CPU with 25.5°C is highly unusable; normally they are much hotter.
Really? I dunno... my AMD X2 3800+ runs at idle between 30°C and 32°C. Under load it can sometimes reach 42°C to 45°C (if both cores are at 100%). What helps is that I have a very good quality heatsink and massive (low noise) fan for cooling. A friend runs his system with water cooling and at idle, the CPUs are about 25°C.
C. so do I. Apart from massive low noise cooling this is a underpowered P4/2800. And it also reaches 45°C, if I use it harder.
So don't worry, I do not have the impression that the CPU is unusable ;-)) regards Eberhard -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
Clayton wrote:
M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor
I don't know if I would trust these temperature measurements. A CPU with 25.5°C is highly unusable; normally they are much hotter.
Really? I dunno... my AMD X2 3800+ runs at idle between 30°C and 32°C. Under load it can sometimes reach 42°C to 45°C (if both cores are at 100%). What helps is that I have a very good quality heatsink and massive (low noise) fan for cooling. A friend runs his system with water cooling and at idle, the CPUs are about 25°C.
The CPU temperature can never be less than the ambient temperature - unless there is refrigeration involved. Assuming that the temperature in your friend's room is 23C then his CPU is running at 2C in idle? Cheers. -- In a period of great joy and pleasure you are comforted by the thought that tragedy is just around the corner. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
On Tuesday 09 January 2007 03:56, Eberhard Roloff wrote:
w83627thf-isa-0290 Adapter: ISA adapter VCore: +1.60 V (min = +0.00 V, max = +3.84 V) +12V: +12.28 V (min = +7.78 V, max = +0.00 V) ALARM +3.3V: +3.36 V (min = +0.42 V, max = +0.74 V) ALARM +5V: +5.04 V (min = +3.65 V, max = +4.56 V) ALARM -12V: +6.06 V (min = +0.14 V, max = -12.20 V) ALARM V5SB: +5.08 V (min = +0.97 V, max = +1.02 V) ALARM VBat: +0.16 V (min = +2.56 V, max = +1.17 V) ALARM fan1: 0 RPM (min = -1 RPM, div = 128) ALARM CPU Fan: 2872 RPM (min = -1 RPM, div = 2) ALARM fan3: 0 RPM (min = 292 RPM, div = 128) ALARM M/B Temp: +32°C (high = +65°C, hyst = +0°C) sensor = thermistor CPU Temp: +25.5°C (high = +80°C, hyst = +75°C) sensor = thermistor temp3: -48.0°C (high = +80°C, hyst = +75°C) sensor = thermistor vid: +1.525 V (VRM Version 9.0) alarms: beep_enable: ### end of sensors output ###
It seems that your /etc/sensors.conf needs some work. This is result of mine after editing conf file: w83697hf-isa-0290 Adapter: ISA adapter VCore: +1.70 V (min = +1.60 V, max = +1.76 V) +3.3V: +3.25 V (min = +3.14 V, max = +3.47 V) +5V: +4.84 V (min = +4.76 V, max = +5.24 V) +12V: +11.55 V (min = +10.82 V, max = +13.19 V) -12V: -12.28 V (min = -13.18 V, max = -10.80 V) -5V: -5.05 V (min = -5.25 V, max = -4.75 V) V5SB: +5.40 V (min = +4.49 V, max = +5.51 V) VBat: +3.31 V (min = +2.40 V, max = +3.60 V) CPU fan: 3183 RPM (min = 2636 RPM, div = 8) Case: +33°C (high = +40°C, hyst = +37°C) sensor = thermistor CPU temp: +60.5°C (high = +70°C, hyst = +67°C) sensor = diode (beep) You can't see ALARM in almost every row. -- Regards, Rajko. http://en.opensuse.org/Portal -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
participants (7)
-
Basil Chupin -
Clayton -
Eberhard Roloff -
James Knott -
Joachim Schrod -
Martin Mielke -
Rajko M.