[opensuse] Blank screen with intel driver on Lenovo IdeaPad305
Hi, I am trying to get OpenSuse 13.2 to run on Lenovo IdeaPad305-15. It uses intel 915 driver for X11. As soon as it boots X, the screen goes blanc. I am guessing the backlight gets turned off, because I can see the outlines of the login box very faintly. There are no obvious error and warning messages in the logs. I tried several recipes from the internet to get everything to start. If I use "nomodeset" option to boot, X does not start at all. "acpi_osi=Linux acpi_backlight=vendor" still results in blank screen. The only way I can boot is by using "nomodeset x11failsafe" option, which means that a vesa driver is used. What else can I do to get the intel driver to boot? I pasted my hardware info and Xorg.log below Myrosia 00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 0e) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3986 Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at 90000000 (32-bit, non-prefetchable) [size=4M] Memory at 80000000 (32-bit, prefetchable) [size=256M] I/O ports at 2050 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: [d0] Power Management version 2 Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [b0] Vendor Specific Information: Len=07 > Kernel modules: i915 [ 22.247] X.Org X Server 1.16.1 Release Date: 2014-09-21 [ 22.247] X Protocol Version 11, Revision 0 [ 22.247] Build Operating System: openSUSE SUSE LINUX [ 22.247] Current Operating System: Linux linux-o7j2 3.16.7-24-desktop #1 SMP PREEMPT Mon Aug 3 14:37:06 UTC 2015 (ec183cc) x86_64 [ 22.247] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.16.7-24-desktop root=UUID=6d530929-7076-48df-984a-9298b9b8029b ro resume=/dev/sda8 splash=silent quiet showopts [ 22.247] Build Date: 12 June 2015 07:55:09PM [ 22.247] [ 22.247] Current version of pixman: 0.32.6 [ 22.247] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 22.247] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 22.247] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Sep 28 18:35:23 2015 [ 22.289] (==) Using config directory: "/etc/X11/xorg.conf.d" [ 22.289] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 22.291] (==) No Layout section. Using the first Screen section. [ 22.291] (==) No screen section available. Using defaults. [ 22.291] (**) |-->Screen "Default Screen Section" (0) [ 22.291] (**) | |-->Monitor "<default monitor>" [ 22.292] (==) No device specified for screen "Default Screen Section". Using the first device section listed. [ 22.292] (**) | |-->Device "Intel Graphics" [ 22.292] (==) No monitor specified for screen "Default Screen Section". Using a default monitor configuration. [ 22.292] (==) Automatically adding devices [ 22.292] (==) Automatically enabling devices [ 22.292] (==) Automatically adding GPU devices [ 22.687] (WW) The directory "/usr/share/fonts/misc/sgi" does not exist. [ 22.687] Entry deleted from font path. [ 22.796] (==) FontPath set to: /usr/share/fonts/misc:unscaled, /usr/share/fonts/Type1/, /usr/share/fonts/100dpi:unscaled, /usr/share/fonts/75dpi:unscaled, /usr/share/fonts/ghostscript/, /usr/share/fonts/cyrillic:unscaled, /usr/share/fonts/truetype/, built-ins [ 22.796] (==) ModulePath set to "/usr/lib64/xorg/modules" [ 22.796] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 22.796] (II) Loader magic: 0x80ec80 [ 22.796] (II) Module ABI versions: [ 22.796] X.Org ANSI C Emulation: 0.4 [ 22.796] X.Org Video Driver: 18.0 [ 22.796] X.Org XInput driver : 21.0 [ 22.796] X.Org Server Extension : 8.0 [ 22.796] (II) xfree86: Adding drm device (/dev/dri/card0) [ 22.799] (--) PCI:*(0:0:2:0) 8086:0f31:17aa:3986 rev 14, Mem @ 0x90000000/4194304, 0x80000000/268435456, I/O @ 0x00002050/8 [ 22.799] (II) LoadModule: "glx" [ 23.288] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so [ 23.305] (II) Module glx: vendor="X.Org Foundation" [ 23.306] compiled for 1.16.1, module version = 1.0.0 [ 23.306] ABI class: X.Org Server Extension, version 8.0 [ 23.306] (==) AIGLX enabled [ 23.306] (II) LoadModule: "intel" [ 23.306] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so [ 23.418] (II) Module intel: vendor="X.Org Foundation" [ 23.418] compiled for 1.16.1, module version = 2.99.916 [ 23.418] Module class: X.Org Video Driver [ 23.418] ABI class: X.Org Video Driver, version 18.0 [ 23.418] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43 [ 23.419] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000 [ 23.419] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100 [ 23.419] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300 [ 23.420] (++) using VT number 7 [ 23.420] (II) intel(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 23.420] (==) intel(0): Depth 24, (--) framebuffer bpp 32 [ 23.420] (==) intel(0): RGB weight 888 [ 23.420] (==) intel(0): Default visual is TrueColor [ 23.420] (**) intel(0): Option "AccelMethod" "uxa" [ 23.420] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics [ 23.421] (**) intel(0): Relaxed fencing enabled [ 23.421] (**) intel(0): Wait on SwapBuffers? enabled [ 23.421] (**) intel(0): Triple buffering? enabled [ 23.421] (**) intel(0): Framebuffer tiled [ 23.421] (**) intel(0): Pixmaps tiled [ 23.421] (**) intel(0): 3D buffers tiled [ 23.421] (**) intel(0): SwapBuffers wait enabled [ 23.421] (==) intel(0): video overlay key set to 0x101fe [ 23.458] (II) intel(0): Output eDP1 has no monitor section [ 23.458] (--) intel(0): found backlight control interface intel_backlight [ 23.494] (II) intel(0): Output VGA1 has no monitor section [ 23.497] (II) intel(0): Output HDMI1 has no monitor section [ 23.523] (II) intel(0): Output DP1 has no monitor section [ 23.577] (II) intel(0): Output HDMI2 has no monitor section [ 23.654] (II) intel(0): EDID for output eDP1 [ 23.654] (II) intel(0): Manufacturer: SDC Model: 3652 Serial#: 0 [ 23.654] (II) intel(0): Year: 2014 Week: 0 [ 23.654] (II) intel(0): EDID Version: 1.3 [ 23.654] (II) intel(0): Digital Display Input [ 23.654] (II) intel(0): DFP 1.x compatible TMDS [ 23.654] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19 [ 23.654] (II) intel(0): Gamma: 2.20 [ 23.654] (II) intel(0): No DPMS capabilities specified [ 23.654] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 [ 23.654] (II) intel(0): First detailed timing is preferred mode [ 23.654] (II) intel(0): redX: 0.575 redY: 0.335 greenX: 0.340 greenY: 0.560 [ 23.654] (II) intel(0): blueX: 0.160 blueY: 0.125 whiteX: 0.313 whiteY: 0.329 [ 23.654] (II) intel(0): Manufacturer's mask: 0 [ 23.654] (II) intel(0): Supported detailed timing: [ 23.654] (II) intel(0): clock: 72.3 MHz Image Size: 344 x 194 mm [ 23.654] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0 [ 23.654] (II) intel(0): v_active: 768 v_sync: 770 v_sync_end 775 v_blanking: 790 v_border: 0 [ 23.654] (II) intel(0): Unknown vendor-specific block f [ 23.654] (II) intel(0): SAMSUNG [ 23.654] (II) intel(0): LTN156AT37402 [ 23.654] (II) intel(0): EDID (in hex): [ 23.654] (II) intel(0): 00ffffffffffff004c83523600000000 [ 23.654] (II) intel(0): 00180103952213780a71059355578f29 [ 23.654] (II) intel(0): 20505400000001010101010101010101 [ 23.654] (II) intel(0): 010101010101411c56a0500016303020 [ 23.655] (II) intel(0): 250058c2100000190000000f00000000 [ 23.655] (II) intel(0): 00000000002052031500000000fe0053 [ 23.655] (II) intel(0): 414d53554e470a204c834154000000fe [ 23.655] (II) intel(0): 004c544e313536415433373430320005 [ 23.655] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported) [ 23.655] (II) intel(0): Printing probed modes for output eDP1 [ 23.655] (II) intel(0): Modeline "1366x768"x60.0 72.33 1366 1414 1446 1526 768 770 775 790 -hsync -vsync (47.4 kHz eP) [ 23.655] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d) [ 23.655] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d) [ 23.655] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d) [ 23.655] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d) [ 23.705] (II) intel(0): EDID for output VGA1 [ 23.737] (II) intel(0): EDID for output HDMI1 [ 23.759] (II) intel(0): EDID for output DP1 [ 23.817] (II) intel(0): EDID for output HDMI2 [ 23.817] (II) intel(0): Output eDP1 connected [ 23.817] (II) intel(0): Output VGA1 disconnected [ 23.817] (II) intel(0): Output HDMI1 disconnected [ 23.817] (II) intel(0): Output DP1 disconnected [ 23.817] (II) intel(0): Output HDMI2 disconnected [ 23.817] (II) intel(0): Using exact sizes for initial modes [ 23.817] (II) intel(0): Output eDP1 using initial mode 1366x768 [ 23.817] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 23.817] (II) intel(0): Kernel page flipping support detected, enabling [ 23.817] (==) intel(0): DPI set to (96, 96) [ 23.817] (II) Loading sub module "fb" [ 23.818] (II) LoadModule: "fb" [ 23.820] (II) Loading /usr/lib64/xorg/modules/libfb.so [ 23.821] (II) Module fb: vendor="X.Org Foundation" [ 23.821] compiled for 1.16.1, module version = 1.0.0 [ 23.821] ABI class: X.Org ANSI C Emulation, version 0.4 [ 23.821] (II) Loading sub module "dri2" [ 23.821] (II) LoadModule: "dri2" [ 23.822] (II) Module "dri2" already built-in [ 23.822] (==) Depth 24 pixmap format is 32 bpp [ 23.822] (II) intel(0): Allocated new frame buffer 1366x768 stride 5632, untiled [ 23.828] (II) UXA(0): Driver registered support for the following operations: [ 23.829] (II) solid [ 23.829] (II) copy [ 23.829] (II) composite (RENDER acceleration) [ 23.829] (II) put_image [ 23.829] (II) get_image [ 23.829] (II) intel(0): [DRI2] Setup complete [ 23.829] (II) intel(0): [DRI2] DRI driver: i965 [ 23.829] (II) intel(0): [DRI2] VDPAU driver: i965 [ 23.829] (==) intel(0): Backing store enabled [ 23.829] (==) intel(0): Silken mouse enabled [ 23.830] (II) intel(0): Initializing HW Cursor [ 23.830] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 23.831] (==) intel(0): DPMS enabled [ 23.831] (==) intel(0): Intel XvMC decoder enabled [ 23.831] (II) intel(0): Set up textured video [ 23.831] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 23.831] (II) intel(0): DRI2: Enabled [ 23.831] (II) intel(0): DRI3: Not available [ 23.831] (==) intel(0): hotplug detection: "enabled" [ 23.848] (--) RandR disabled [ 24.217] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context_profile [ 24.217] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile [ 24.217] (II) AIGLX: enabled GLX_INTEL_swap_event [ 24.217] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control [ 24.217] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB [ 24.217] (II) AIGLX: enabled GLX_ARB_fbconfig_float [ 24.217] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context_robustness [ 24.217] (II) AIGLX: Loaded and initialized i965 [ 24.217] (II) GLX: Initialized DRI2 GL provider for screen 0 [ 24.219] (II) intel(0): Setting screen physical size to 361 x 203 [ 24.647] (II) config/udev: Adding input device Power Button (/dev/input/event4) [ 24.647] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.647] (**) Power Button: Applying InputClass "system-keyboard" [ 24.647] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.647] (II) LoadModule: "evdev" [ 24.648] (II) Loading /usr/lib64/xorg/modules/input/evdev_drv.so [ 24.694] (II) Module evdev: vendor="X.Org Foundation" [ 24.694] compiled for 1.16.1, module version = 2.9.0 [ 24.694] Module class: X.Org XInput Driver [ 24.694] ABI class: X.Org XInput driver, version 21.0 [ 24.694] (II) Using input driver 'evdev' for 'Power Button' [ 24.694] (**) Power Button: always reports core events [ 24.694] (**) evdev: Power Button: Device: "/dev/input/event4" [ 24.695] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 24.695] (--) evdev: Power Button: Found keys [ 24.695] (II) evdev: Power Button: Configuring as keyboard [ 24.695] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5/event4" [ 24.695] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6) [ 24.695] (**) Option "xkb_rules" "evdev" [ 24.695] (**) Option "xkb_model" "pc105" [ 24.695] (**) Option "xkb_layout" "gb" [ 24.695] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.744] (II) config/udev: Adding input device Video Bus (/dev/input/event5) [ 24.744] (**) Video Bus: Applying InputClass "evdev keyboard catchall" [ 24.744] (**) Video Bus: Applying InputClass "system-keyboard" [ 24.744] (**) Video Bus: Applying InputClass "evdev keyboard catchall" [ 24.744] (II) Using input driver 'evdev' for 'Video Bus' [ 24.744] (**) Video Bus: always reports core events [ 24.744] (**) evdev: Video Bus: Device: "/dev/input/event5" [ 24.744] (--) evdev: Video Bus: Vendor 0 Product 0x6 [ 24.744] (--) evdev: Video Bus: Found keys [ 24.744] (II) evdev: Video Bus: Configuring as keyboard [ 24.745] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6/event5" [ 24.745] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7) [ 24.745] (**) Option "xkb_rules" "evdev" [ 24.745] (**) Option "xkb_model" "pc105" [ 24.745] (**) Option "xkb_layout" "gb" [ 24.745] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.745] (II) config/udev: Adding input device Lid Switch (/dev/input/event2) [ 24.746] (II) No input driver specified, ignoring this device. [ 24.746] (II) This device may have been added with another device file. [ 24.746] (II) config/udev: Adding input device Power Button (/dev/input/event3) [ 24.746] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.746] (**) Power Button: Applying InputClass "system-keyboard" [ 24.746] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.746] (II) Using input driver 'evdev' for 'Power Button' [ 24.746] (**) Power Button: always reports core events [ 24.746] (**) evdev: Power Button: Device: "/dev/input/event3" [ 24.746] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 24.746] (--) evdev: Power Button: Found keys [ 24.746] (II) evdev: Power Button: Configuring as keyboard [ 24.746] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4/event3" [ 24.746] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8) [ 24.746] (**) Option "xkb_rules" "evdev" [ 24.746] (**) Option "xkb_model" "pc105" [ 24.746] (**) Option "xkb_layout" "gb" [ 24.746] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.748] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event8) [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall" [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "system-keyboard" [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall" [ 24.748] (II) Using input driver 'evdev' for 'Lenovo EasyCamera' [ 24.748] (**) Lenovo EasyCamera: always reports core events [ 24.748] (**) evdev: Lenovo EasyCamera: Device: "/dev/input/event8" [ 24.748] (--) evdev: Lenovo EasyCamera: Vendor 0xbda Product 0x579c [ 24.748] (--) evdev: Lenovo EasyCamera: Found keys [ 24.748] (II) evdev: Lenovo EasyCamera: Configuring as keyboard [ 24.748] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4.3/1-4.3:1.0/input/input9/event8" [ 24.748] (II) XINPUT: Adding extended input device "Lenovo EasyCamera" (type: KEYBOARD, id 9) [ 24.748] (**) Option "xkb_rules" "evdev" [ 24.748] (**) Option "xkb_model" "pc105" [ 24.748] (**) Option "xkb_layout" "gb" [ 24.748] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.749] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event9) [ 24.749] (II) No input driver specified, ignoring this device. [ 24.749] (II) This device may have been added with another device file. [ 24.749] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event10) [ 24.749] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.750] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event11) [ 24.750] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.750] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event12) [ 24.750] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.751] (II) config/udev: Adding input device Ideapad extra buttons (/dev/input/event7) [ 24.751] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall" [ 24.751] (**) Ideapad extra buttons: Applying InputClass "system-keyboard" [ 24.751] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall" [ 24.751] (II) Using input driver 'evdev' for 'Ideapad extra buttons' [ 24.751] (**) Ideapad extra buttons: always reports core events [ 24.751] (**) evdev: Ideapad extra buttons: Device: "/dev/input/event7" [ 24.751] (--) evdev: Ideapad extra buttons: Vendor 0 Product 0 [ 24.751] (--) evdev: Ideapad extra buttons: Found keys [ 24.751] (II) evdev: Ideapad extra buttons: Configuring as keyboard [ 24.751] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input8/event7" [ 24.751] (II) XINPUT: Adding extended input device "Ideapad extra buttons" (type: KEYBOARD, id 10) [ 24.751] (**) Option "xkb_rules" "evdev" [ 24.751] (**) Option "xkb_model" "pc105" [ 24.751] (**) Option "xkb_layout" "gb" [ 24.751] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.752] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0) [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall" [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard" [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall" [ 24.752] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard' [ 24.752] (**) AT Translated Set 2 keyboard: always reports core events [ 24.752] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0" [ 24.752] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1 [ 24.752] (--) evdev: AT Translated Set 2 keyboard: Found keys [ 24.752] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard [ 24.752] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0" [ 24.753] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 11) [ 24.753] (**) Option "xkb_rules" "evdev" [ 24.753] (**) Option "xkb_model" "pc105" [ 24.753] (**) Option "xkb_layout" "gb" [ 24.753] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.753] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event1) [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons" [ 24.754] (II) LoadModule: "synaptics" [ 24.754] (II) Loading /usr/lib64/xorg/modules/input/synaptics_drv.so [ 24.754] (II) Module synaptics: vendor="X.Org Foundation" [ 24.754] compiled for 1.16.1, module version = 1.8.1 [ 24.754] Module class: X.Org XInput Driver [ 24.754] ABI class: X.Org XInput driver, version 21.0 [ 24.754] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad' [ 24.755] (**) SynPS/2 Synaptics TouchPad: always reports core events [ 24.755] (**) Option "Device" "/dev/input/event1" [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5670 (res 44) [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4794 (res 76) [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255 [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15 [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7 [ 24.785] (**) Option "HorizEdgeScroll" "off" [ 24.785] (**) Option "TapButton1" "1" [ 24.785] (**) Option "TapButton2" "3" [ 24.785] (**) Option "TapButton3" "2" [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found [ 24.785] (**) SynPS/2 Synaptics TouchPad: always reports core events [ 24.822] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input2/event1" [ 24.822] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 12) [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5 [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75 [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.037 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4 [ 24.823] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found [ 24.823] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0) [ 24.823] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates" [ 24.823] (II) config/udev: Adding input device PC Speaker (/dev/input/event6) [ 24.823] (II) No input driver specified, ignoring this device. [ 24.823] (II) This device may have been added with another device file. [ 1022.066] (II) UnloadModule: "synaptics" [ 1022.066] (II) evdev: AT Translated Set 2 keyboard: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Ideapad extra buttons: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Lenovo EasyCamera: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Power Button: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Video Bus: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.067] (II) evdev: Power Button: Close [ 1022.067] (II) UnloadModule: "evdev" [ 1025.087] (EE) Server terminated successfully (0). Closing log file. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
I solved the problem myself. This turned out to be an "Inverted
brightness" issue as documented here
https://wiki.archlinux.org/index.php/Backlight#Inverted_Brightness_.28Intel_...
Adding i915.invert_brightness=1 on boot solved the issue.
Myrosia
On Mon, Sep 28, 2015 at 7:21 PM, Myrosia Dzikovska
Hi,
I am trying to get OpenSuse 13.2 to run on Lenovo IdeaPad305-15. It uses intel 915 driver for X11. As soon as it boots X, the screen goes blanc. I am guessing the backlight gets turned off, because I can see the outlines of the login box very faintly.
There are no obvious error and warning messages in the logs. I tried several recipes from the internet to get everything to start. If I use "nomodeset" option to boot, X does not start at all. "acpi_osi=Linux acpi_backlight=vendor" still results in blank screen. The only way I can boot is by using "nomodeset x11failsafe" option, which means that a vesa driver is used. What else can I do to get the intel driver to boot? I pasted my hardware info and Xorg.log below
Myrosia
00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 0e) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3986 Flags: bus master, fast devsel, latency 0, IRQ 255 Memory at 90000000 (32-bit, non-prefetchable) [size=4M] Memory at 80000000 (32-bit, prefetchable) [size=256M] I/O ports at 2050 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: [d0] Power Management version 2 Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [b0] Vendor Specific Information: Len=07 > Kernel modules: i915
[ 22.247] X.Org X Server 1.16.1 Release Date: 2014-09-21 [ 22.247] X Protocol Version 11, Revision 0 [ 22.247] Build Operating System: openSUSE SUSE LINUX [ 22.247] Current Operating System: Linux linux-o7j2 3.16.7-24-desktop #1 SMP PREEMPT Mon Aug 3 14:37:06 UTC 2015 (ec183cc) x86_64 [ 22.247] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.16.7-24-desktop root=UUID=6d530929-7076-48df-984a-9298b9b8029b ro resume=/dev/sda8 splash=silent quiet showopts [ 22.247] Build Date: 12 June 2015 07:55:09PM [ 22.247] [ 22.247] Current version of pixman: 0.32.6 [ 22.247] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 22.247] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 22.247] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Sep 28 18:35:23 2015 [ 22.289] (==) Using config directory: "/etc/X11/xorg.conf.d" [ 22.289] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 22.291] (==) No Layout section. Using the first Screen section. [ 22.291] (==) No screen section available. Using defaults. [ 22.291] (**) |-->Screen "Default Screen Section" (0) [ 22.291] (**) | |-->Monitor "<default monitor>" [ 22.292] (==) No device specified for screen "Default Screen Section". Using the first device section listed. [ 22.292] (**) | |-->Device "Intel Graphics" [ 22.292] (==) No monitor specified for screen "Default Screen Section". Using a default monitor configuration. [ 22.292] (==) Automatically adding devices [ 22.292] (==) Automatically enabling devices [ 22.292] (==) Automatically adding GPU devices [ 22.687] (WW) The directory "/usr/share/fonts/misc/sgi" does not exist. [ 22.687] Entry deleted from font path. [ 22.796] (==) FontPath set to: /usr/share/fonts/misc:unscaled, /usr/share/fonts/Type1/, /usr/share/fonts/100dpi:unscaled, /usr/share/fonts/75dpi:unscaled, /usr/share/fonts/ghostscript/, /usr/share/fonts/cyrillic:unscaled, /usr/share/fonts/truetype/, built-ins [ 22.796] (==) ModulePath set to "/usr/lib64/xorg/modules" [ 22.796] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 22.796] (II) Loader magic: 0x80ec80 [ 22.796] (II) Module ABI versions: [ 22.796] X.Org ANSI C Emulation: 0.4 [ 22.796] X.Org Video Driver: 18.0 [ 22.796] X.Org XInput driver : 21.0 [ 22.796] X.Org Server Extension : 8.0 [ 22.796] (II) xfree86: Adding drm device (/dev/dri/card0) [ 22.799] (--) PCI:*(0:0:2:0) 8086:0f31:17aa:3986 rev 14, Mem @ 0x90000000/4194304, 0x80000000/268435456, I/O @ 0x00002050/8 [ 22.799] (II) LoadModule: "glx" [ 23.288] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so [ 23.305] (II) Module glx: vendor="X.Org Foundation" [ 23.306] compiled for 1.16.1, module version = 1.0.0 [ 23.306] ABI class: X.Org Server Extension, version 8.0 [ 23.306] (==) AIGLX enabled [ 23.306] (II) LoadModule: "intel" [ 23.306] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so [ 23.418] (II) Module intel: vendor="X.Org Foundation" [ 23.418] compiled for 1.16.1, module version = 2.99.916 [ 23.418] Module class: X.Org Video Driver [ 23.418] ABI class: X.Org Video Driver, version 18.0 [ 23.418] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43 [ 23.419] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000 [ 23.419] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100 [ 23.419] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300 [ 23.420] (++) using VT number 7
[ 23.420] (II) intel(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 23.420] (==) intel(0): Depth 24, (--) framebuffer bpp 32 [ 23.420] (==) intel(0): RGB weight 888 [ 23.420] (==) intel(0): Default visual is TrueColor [ 23.420] (**) intel(0): Option "AccelMethod" "uxa" [ 23.420] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics [ 23.421] (**) intel(0): Relaxed fencing enabled [ 23.421] (**) intel(0): Wait on SwapBuffers? enabled [ 23.421] (**) intel(0): Triple buffering? enabled [ 23.421] (**) intel(0): Framebuffer tiled [ 23.421] (**) intel(0): Pixmaps tiled [ 23.421] (**) intel(0): 3D buffers tiled [ 23.421] (**) intel(0): SwapBuffers wait enabled [ 23.421] (==) intel(0): video overlay key set to 0x101fe [ 23.458] (II) intel(0): Output eDP1 has no monitor section [ 23.458] (--) intel(0): found backlight control interface intel_backlight [ 23.494] (II) intel(0): Output VGA1 has no monitor section [ 23.497] (II) intel(0): Output HDMI1 has no monitor section [ 23.523] (II) intel(0): Output DP1 has no monitor section [ 23.577] (II) intel(0): Output HDMI2 has no monitor section [ 23.654] (II) intel(0): EDID for output eDP1 [ 23.654] (II) intel(0): Manufacturer: SDC Model: 3652 Serial#: 0 [ 23.654] (II) intel(0): Year: 2014 Week: 0 [ 23.654] (II) intel(0): EDID Version: 1.3 [ 23.654] (II) intel(0): Digital Display Input [ 23.654] (II) intel(0): DFP 1.x compatible TMDS [ 23.654] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19 [ 23.654] (II) intel(0): Gamma: 2.20 [ 23.654] (II) intel(0): No DPMS capabilities specified [ 23.654] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 [ 23.654] (II) intel(0): First detailed timing is preferred mode [ 23.654] (II) intel(0): redX: 0.575 redY: 0.335 greenX: 0.340 greenY: 0.560 [ 23.654] (II) intel(0): blueX: 0.160 blueY: 0.125 whiteX: 0.313 whiteY: 0.329 [ 23.654] (II) intel(0): Manufacturer's mask: 0 [ 23.654] (II) intel(0): Supported detailed timing: [ 23.654] (II) intel(0): clock: 72.3 MHz Image Size: 344 x 194 mm [ 23.654] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0 [ 23.654] (II) intel(0): v_active: 768 v_sync: 770 v_sync_end 775 v_blanking: 790 v_border: 0 [ 23.654] (II) intel(0): Unknown vendor-specific block f [ 23.654] (II) intel(0): SAMSUNG [ 23.654] (II) intel(0): LTN156AT37402 [ 23.654] (II) intel(0): EDID (in hex): [ 23.654] (II) intel(0): 00ffffffffffff004c83523600000000 [ 23.654] (II) intel(0): 00180103952213780a71059355578f29 [ 23.654] (II) intel(0): 20505400000001010101010101010101 [ 23.654] (II) intel(0): 010101010101411c56a0500016303020 [ 23.655] (II) intel(0): 250058c2100000190000000f00000000 [ 23.655] (II) intel(0): 00000000002052031500000000fe0053 [ 23.655] (II) intel(0): 414d53554e470a204c834154000000fe [ 23.655] (II) intel(0): 004c544e313536415433373430320005 [ 23.655] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported) [ 23.655] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported) [ 23.655] (II) intel(0): Printing probed modes for output eDP1 [ 23.655] (II) intel(0): Modeline "1366x768"x60.0 72.33 1366 1414 1446 1526 768 770 775 790 -hsync -vsync (47.4 kHz eP) [ 23.655] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d) [ 23.655] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d) [ 23.655] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d) [ 23.655] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d) [ 23.705] (II) intel(0): EDID for output VGA1 [ 23.737] (II) intel(0): EDID for output HDMI1 [ 23.759] (II) intel(0): EDID for output DP1 [ 23.817] (II) intel(0): EDID for output HDMI2 [ 23.817] (II) intel(0): Output eDP1 connected [ 23.817] (II) intel(0): Output VGA1 disconnected [ 23.817] (II) intel(0): Output HDMI1 disconnected [ 23.817] (II) intel(0): Output DP1 disconnected [ 23.817] (II) intel(0): Output HDMI2 disconnected [ 23.817] (II) intel(0): Using exact sizes for initial modes [ 23.817] (II) intel(0): Output eDP1 using initial mode 1366x768 [ 23.817] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 23.817] (II) intel(0): Kernel page flipping support detected, enabling [ 23.817] (==) intel(0): DPI set to (96, 96) [ 23.817] (II) Loading sub module "fb" [ 23.818] (II) LoadModule: "fb" [ 23.820] (II) Loading /usr/lib64/xorg/modules/libfb.so [ 23.821] (II) Module fb: vendor="X.Org Foundation" [ 23.821] compiled for 1.16.1, module version = 1.0.0 [ 23.821] ABI class: X.Org ANSI C Emulation, version 0.4 [ 23.821] (II) Loading sub module "dri2" [ 23.821] (II) LoadModule: "dri2" [ 23.822] (II) Module "dri2" already built-in [ 23.822] (==) Depth 24 pixmap format is 32 bpp [ 23.822] (II) intel(0): Allocated new frame buffer 1366x768 stride 5632, untiled [ 23.828] (II) UXA(0): Driver registered support for the following operations: [ 23.829] (II) solid [ 23.829] (II) copy [ 23.829] (II) composite (RENDER acceleration) [ 23.829] (II) put_image [ 23.829] (II) get_image [ 23.829] (II) intel(0): [DRI2] Setup complete [ 23.829] (II) intel(0): [DRI2] DRI driver: i965 [ 23.829] (II) intel(0): [DRI2] VDPAU driver: i965 [ 23.829] (==) intel(0): Backing store enabled [ 23.829] (==) intel(0): Silken mouse enabled [ 23.830] (II) intel(0): Initializing HW Cursor [ 23.830] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 23.831] (==) intel(0): DPMS enabled [ 23.831] (==) intel(0): Intel XvMC decoder enabled [ 23.831] (II) intel(0): Set up textured video [ 23.831] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 23.831] (II) intel(0): DRI2: Enabled [ 23.831] (II) intel(0): DRI3: Not available [ 23.831] (==) intel(0): hotplug detection: "enabled" [ 23.848] (--) RandR disabled [ 24.217] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context_profile [ 24.217] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile [ 24.217] (II) AIGLX: enabled GLX_INTEL_swap_event [ 24.217] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control [ 24.217] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB [ 24.217] (II) AIGLX: enabled GLX_ARB_fbconfig_float [ 24.217] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects [ 24.217] (II) AIGLX: enabled GLX_ARB_create_context_robustness [ 24.217] (II) AIGLX: Loaded and initialized i965 [ 24.217] (II) GLX: Initialized DRI2 GL provider for screen 0 [ 24.219] (II) intel(0): Setting screen physical size to 361 x 203 [ 24.647] (II) config/udev: Adding input device Power Button (/dev/input/event4) [ 24.647] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.647] (**) Power Button: Applying InputClass "system-keyboard" [ 24.647] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.647] (II) LoadModule: "evdev" [ 24.648] (II) Loading /usr/lib64/xorg/modules/input/evdev_drv.so [ 24.694] (II) Module evdev: vendor="X.Org Foundation" [ 24.694] compiled for 1.16.1, module version = 2.9.0 [ 24.694] Module class: X.Org XInput Driver [ 24.694] ABI class: X.Org XInput driver, version 21.0 [ 24.694] (II) Using input driver 'evdev' for 'Power Button' [ 24.694] (**) Power Button: always reports core events [ 24.694] (**) evdev: Power Button: Device: "/dev/input/event4" [ 24.695] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 24.695] (--) evdev: Power Button: Found keys [ 24.695] (II) evdev: Power Button: Configuring as keyboard [ 24.695] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5/event4" [ 24.695] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6) [ 24.695] (**) Option "xkb_rules" "evdev" [ 24.695] (**) Option "xkb_model" "pc105" [ 24.695] (**) Option "xkb_layout" "gb" [ 24.695] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.744] (II) config/udev: Adding input device Video Bus (/dev/input/event5) [ 24.744] (**) Video Bus: Applying InputClass "evdev keyboard catchall" [ 24.744] (**) Video Bus: Applying InputClass "system-keyboard" [ 24.744] (**) Video Bus: Applying InputClass "evdev keyboard catchall" [ 24.744] (II) Using input driver 'evdev' for 'Video Bus' [ 24.744] (**) Video Bus: always reports core events [ 24.744] (**) evdev: Video Bus: Device: "/dev/input/event5" [ 24.744] (--) evdev: Video Bus: Vendor 0 Product 0x6 [ 24.744] (--) evdev: Video Bus: Found keys [ 24.744] (II) evdev: Video Bus: Configuring as keyboard [ 24.745] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6/event5" [ 24.745] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7) [ 24.745] (**) Option "xkb_rules" "evdev" [ 24.745] (**) Option "xkb_model" "pc105" [ 24.745] (**) Option "xkb_layout" "gb" [ 24.745] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.745] (II) config/udev: Adding input device Lid Switch (/dev/input/event2) [ 24.746] (II) No input driver specified, ignoring this device. [ 24.746] (II) This device may have been added with another device file. [ 24.746] (II) config/udev: Adding input device Power Button (/dev/input/event3) [ 24.746] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.746] (**) Power Button: Applying InputClass "system-keyboard" [ 24.746] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 24.746] (II) Using input driver 'evdev' for 'Power Button' [ 24.746] (**) Power Button: always reports core events [ 24.746] (**) evdev: Power Button: Device: "/dev/input/event3" [ 24.746] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 24.746] (--) evdev: Power Button: Found keys [ 24.746] (II) evdev: Power Button: Configuring as keyboard [ 24.746] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4/event3" [ 24.746] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8) [ 24.746] (**) Option "xkb_rules" "evdev" [ 24.746] (**) Option "xkb_model" "pc105" [ 24.746] (**) Option "xkb_layout" "gb" [ 24.746] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.748] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event8) [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall" [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "system-keyboard" [ 24.748] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall" [ 24.748] (II) Using input driver 'evdev' for 'Lenovo EasyCamera' [ 24.748] (**) Lenovo EasyCamera: always reports core events [ 24.748] (**) evdev: Lenovo EasyCamera: Device: "/dev/input/event8" [ 24.748] (--) evdev: Lenovo EasyCamera: Vendor 0xbda Product 0x579c [ 24.748] (--) evdev: Lenovo EasyCamera: Found keys [ 24.748] (II) evdev: Lenovo EasyCamera: Configuring as keyboard [ 24.748] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4.3/1-4.3:1.0/input/input9/event8" [ 24.748] (II) XINPUT: Adding extended input device "Lenovo EasyCamera" (type: KEYBOARD, id 9) [ 24.748] (**) Option "xkb_rules" "evdev" [ 24.748] (**) Option "xkb_model" "pc105" [ 24.748] (**) Option "xkb_layout" "gb" [ 24.748] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.749] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event9) [ 24.749] (II) No input driver specified, ignoring this device. [ 24.749] (II) This device may have been added with another device file. [ 24.749] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event10) [ 24.749] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.750] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event11) [ 24.750] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.750] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event12) [ 24.750] (II) No input driver specified, ignoring this device. [ 24.750] (II) This device may have been added with another device file. [ 24.751] (II) config/udev: Adding input device Ideapad extra buttons (/dev/input/event7) [ 24.751] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall" [ 24.751] (**) Ideapad extra buttons: Applying InputClass "system-keyboard" [ 24.751] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall" [ 24.751] (II) Using input driver 'evdev' for 'Ideapad extra buttons' [ 24.751] (**) Ideapad extra buttons: always reports core events [ 24.751] (**) evdev: Ideapad extra buttons: Device: "/dev/input/event7" [ 24.751] (--) evdev: Ideapad extra buttons: Vendor 0 Product 0 [ 24.751] (--) evdev: Ideapad extra buttons: Found keys [ 24.751] (II) evdev: Ideapad extra buttons: Configuring as keyboard [ 24.751] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input8/event7" [ 24.751] (II) XINPUT: Adding extended input device "Ideapad extra buttons" (type: KEYBOARD, id 10) [ 24.751] (**) Option "xkb_rules" "evdev" [ 24.751] (**) Option "xkb_model" "pc105" [ 24.751] (**) Option "xkb_layout" "gb" [ 24.751] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.752] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0) [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall" [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard" [ 24.752] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall" [ 24.752] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard' [ 24.752] (**) AT Translated Set 2 keyboard: always reports core events [ 24.752] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0" [ 24.752] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1 [ 24.752] (--) evdev: AT Translated Set 2 keyboard: Found keys [ 24.752] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard [ 24.752] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0" [ 24.753] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 11) [ 24.753] (**) Option "xkb_rules" "evdev" [ 24.753] (**) Option "xkb_model" "pc105" [ 24.753] (**) Option "xkb_layout" "gb" [ 24.753] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 24.753] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event1) [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall" [ 24.754] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons" [ 24.754] (II) LoadModule: "synaptics" [ 24.754] (II) Loading /usr/lib64/xorg/modules/input/synaptics_drv.so [ 24.754] (II) Module synaptics: vendor="X.Org Foundation" [ 24.754] compiled for 1.16.1, module version = 1.8.1 [ 24.754] Module class: X.Org XInput Driver [ 24.754] ABI class: X.Org XInput driver, version 21.0 [ 24.754] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad' [ 24.755] (**) SynPS/2 Synaptics TouchPad: always reports core events [ 24.755] (**) Option "Device" "/dev/input/event1" [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5670 (res 44) [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4794 (res 76) [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255 [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15 [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7 [ 24.785] (**) Option "HorizEdgeScroll" "off" [ 24.785] (**) Option "TapButton1" "1" [ 24.785] (**) Option "TapButton2" "3" [ 24.785] (**) Option "TapButton3" "2" [ 24.785] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found [ 24.785] (**) SynPS/2 Synaptics TouchPad: always reports core events [ 24.822] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input2/event1" [ 24.822] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 12) [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5 [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75 [ 24.822] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.037 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000 [ 24.822] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4 [ 24.823] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found [ 24.823] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0) [ 24.823] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates" [ 24.823] (II) config/udev: Adding input device PC Speaker (/dev/input/event6) [ 24.823] (II) No input driver specified, ignoring this device. [ 24.823] (II) This device may have been added with another device file. [ 1022.066] (II) UnloadModule: "synaptics" [ 1022.066] (II) evdev: AT Translated Set 2 keyboard: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Ideapad extra buttons: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Lenovo EasyCamera: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Power Button: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.066] (II) evdev: Video Bus: Close [ 1022.066] (II) UnloadModule: "evdev" [ 1022.067] (II) evdev: Power Button: Close [ 1022.067] (II) UnloadModule: "evdev" [ 1025.087] (EE) Server terminated successfully (0). Closing log file. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
participants (1)
-
Myrosia Dzikovska