I am trying to get SuSE Linux 7.3 to write and burn a CD-R, and have been folowing the README for koncd. Managed to carry out all procedures outlined in the README namely 1) lines to /etc/modules.conf alias char-major-21 sg # line already there post-install sg modprobe "-k" ide-scsi # line added 2) /etc/lilo.conf append = "hdc=ide-scsi hdb=ide-scsi # line added 3) On reboot no ide-scsi module found with the command lsmod, but after entering # "-k" ide-scsi from the console prompt, the module is loaded 4) Subsequent steps 4,5,6 of the readme carried out ok except that in step 5 I found that /etc/fstab mounts the CD-WRITER as /dev/cdrecorder instead as /dev/cdr as mentioned in the README, so left it unchanged. 5) On running koncd setup there were no error messages, however to my surprise I could not perform any operations on a CD-R. Would like to know how to get the ide-scsi module properly loaded and whether I need to add a line in /etc/fstab to mount /dev/cdr in addition to the line in fstab: /dev/cdrecorder /media/cdrecorder auto ro,noauto,user,exec 0 0 ? Any other tips also please !
** On Sat, 23 Feb 2002 22:19:55 +0100 Roy Leembruggen <r.c.leembruggen@freeler.nl>dashed off this message: **Would like to know how to get the ide-scsi module properly loaded and whether **I need to add a line in /etc/fstab to mount /dev/cdr in addition to the line **in fstab: I may be brain dead here but IIRC, suse7.3 setsup everything you need to make the cdrecorder available ( i.e. none of the fidling w/ append foo ) IF yours isn't actually loading , check to see you have the ide-scsi module started ( I think it's a line added to boot local??? ) Unfortunately I can't check for you as my box is on it's way back to the manufacturers so they can fix what they were suposed to fix origionally! I can tell you I never had much luck w/ the koncd program at all, but Xcdroast seemed to find all scsi and ide scsi cd units w/ no problem... But ymmv -- j afterthought : I'm not Young enough to know everything!
Hello Roy, I have in my "/etc/init.d/boot.local an entry: /sbin/modprobe ide-scsi and my ATAPI DVD-ROM and CD-RW burner work just fine. I only use Xcdroast so YMMV. Ed On Sat, 23 Feb 2002 22:19:55 +0100 Roy Leembruggen <r.c.leembruggen@freeler.nl> wrote:
I am trying to get SuSE Linux 7.3 to write and burn a CD-R, and have been folowing the README for koncd. Managed to carry out all procedures outlined in the README namely
1) lines to /etc/modules.conf alias char-major-21 sg # line already there post-install sg modprobe "-k" ide-scsi # line added
2) /etc/lilo.conf append = "hdc=ide-scsi hdb=ide-scsi # line added
3) On reboot no ide-scsi module found with the command lsmod, but after entering # "-k" ide-scsi from the console prompt, the module is loaded
4) Subsequent steps 4,5,6 of the readme carried out ok except that in step 5 I found that /etc/fstab mounts the CD-WRITER as /dev/cdrecorder instead as /dev/cdr as mentioned in the README, so left it unchanged.
5) On running koncd setup there were no error messages, however to my surprise I could not perform any operations on a CD-R.
Would like to know how to get the ide-scsi module properly loaded and whether I need to add a line in /etc/fstab to mount /dev/cdr in addition to the line in fstab: /dev/cdrecorder /media/cdrecorder auto ro,noauto,user,exec 0 0 ?
Any other tips also please !
-- Edwin O. Erdman Penguinista - diagonally parked in a parallel universe !!! Registered Linux User# 135893 Machine#s 59387, 82657 SuSE 7.3 - KDE 2.2.2 - Sylpheed 7.1
* Edwin O.Erdman <eerdman@wi.rr.com> [02-23-02 17:23] crowed:
Hello Roy, I have in my "/etc/init.d/boot.local an entry: /sbin/modprobe ide-scsi and my ATAPI DVD-ROM and CD-RW burner work just fine. I only use Xcdroast so YMMV.
And I have vanilla install of SuSE7.3pro and do NOT have the added line (ide-scsi). I do have an adapti cdrw (HP9100).
On Sat, 23 Feb 2002 22:19:55 +0100 Roy Leembruggen <r.c.leembruggen@freeler.nl> wrote:
I am trying to get SuSE Linux 7.3 to write and burn a CD-R, and have been folowing the README for koncd. Managed to carry out all procedures outlined in the README namely
1) lines to /etc/modules.conf alias char-major-21 sg # line already there post-install sg modprobe "-k" ide-scsi # line added
2) /etc/lilo.conf append = "hdc=ide-scsi hdb=ide-scsi # line added
3) On reboot no ide-scsi module found with the command lsmod, but after entering # "-k" ide-scsi from the console prompt, the module is loaded
4) Subsequent steps 4,5,6 of the readme carried out ok except that in step 5 I found that /etc/fstab mounts the CD-WRITER as /dev/cdrecorder instead as /dev/cdr as mentioned in the README, so left it unchanged.
5) On running koncd setup there were no error messages, however to my surprise I could not perform any operations on a CD-R.
Would like to know how to get the ide-scsi module properly loaded and whether I need to add a line in /etc/fstab to mount /dev/cdr in addition to the line in fstab: /dev/cdrecorder /media/cdrecorder auto ro,noauto,user,exec 0 0 ?
-- Pat Shanahan Registered Linux User #207535 Registered at: http://counter.li.org
participants (4)
-
Edwin O.Erdman
-
jfweber@bellsouth.net
-
pat
-
Roy Leembruggen