Hello, after upgrade from 13.1 to 13.2 automounting of USB disks in KDE stopped working. Manual mounting works. KDE sometimes shows prompt for root password. It then allows to mount the disk within KDE. Unmounting then doesn't require root password. Autofs is running (and I haven't touched config files), although „systemctl status autofs.service“ says: „automount[22123]: lookup_init:139: lookup(yp): map auto.master: Local domain name not set“. I don't know how relevant this is for the problem. In KDE Config Centre | Removable devices I have for all devices checked automounting. But it doesn't have any effect... Dmesg shows: [39222.693189] usb 3-3: new high-speed USB device number 16 using xhci_hcd [39222.859722] usb 3-3: New USB device found, idVendor=0951, idProduct=1625 [39222.859729] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [39222.859732] usb 3-3: Product: DT 101 II [39222.859735] usb 3-3: Manufacturer: Kingston [39222.859737] usb 3-3: SerialNumber: 001372982D3DA9C096330076 [39222.860367] usb-storage 3-3:1.0: USB Mass Storage device detected [39222.860734] scsi18 : usb-storage 3-3:1.0 [39223.863680] scsi 18:0:0:0: Direct-Access Kingston DT 101 II 1.00 PQ: 0 ANSI: 2 [39223.864060] sd 18:0:0:0: Attached scsi generic sg3 type 0 [39223.864444] sd 18:0:0:0: [sdc] 31277056 512-byte logical blocks: (16.0 GB/14.9 GiB) [39223.864813] sd 18:0:0:0: [sdc] Write Protect is off [39223.864821] sd 18:0:0:0: [sdc] Mode Sense: 23 00 00 00 [39223.865160] sd 18:0:0:0: [sdc] No Caching mode page found [39223.865165] sd 18:0:0:0: [sdc] Assuming drive cache: write through [39223.966081] sdc: sdc1 [39223.967376] sd 18:0:0:0: [sdc] Attached SCSI removable disk [39235.643843] usb 3-3: USB disconnect, device number 16 [39243.309729] usb 3-3: new high-speed USB device number 17 using xhci_hcd [39243.474636] usb 3-3: New USB device found, idVendor=125f, idProduct=a93a [39243.474644] usb 3-3: New USB device strings: Mfr=1, Product=3, SerialNumber=2 [39243.474647] usb 3-3: Product: Portable HDD SH93 [39243.474650] usb 3-3: Manufacturer: ADATA [39243.474653] usb 3-3: SerialNumber: SH0190810190 [39243.475207] usb-storage 3-3:1.0: USB Mass Storage device detected [39243.476273] scsi19 : usb-storage 3-3:1.0 [39244.479114] scsi 19:0:0:0: Direct-Access ADATA HDD SH93 PQ: 0 ANSI: 0 [39244.479690] sd 19:0:0:0: Attached scsi generic sg3 type 0 [39244.479695] sd 19:0:0:0: Embedded Enclosure Device [39244.479745] sd 19:0:0:0: [sdc] 1465149168 512-byte logical blocks: (750 GB/698 GiB) [39244.480092] sd 19:0:0:0: Failed to get diagnostic page 0x8000002 [39244.480095] sd 19:0:0:0: Failed to bind enclosure -19 [39244.480251] sd 19:0:0:0: [sdc] Write Protect is off [39244.480256] sd 19:0:0:0: [sdc] Mode Sense: 03 00 00 00 [39244.480456] sd 19:0:0:0: [sdc] No Caching mode page found [39244.480464] sd 19:0:0:0: [sdc] Assuming drive cache: write through [39244.504825] sdc: sdc1 [39244.505877] sd 19:0:0:0: [sdc] Attached SCSI disk [39253.085857] usb 3-3: USB disconnect, device number 17 Any idea what went wrong? Vojtěch -- Vojtěch Zeisek Komunita openSUSE GNU/Linuxu Community of the openSUSE GNU/Linux http://www.opensuse.org/ http://trapa.cz/