Hi all. I have two similar ATA drives that are recognized by SUSE 10.0 as UDMA 100, see boot.msg excerpt: <6>PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. <6> ide2: BM-DMA at 0x8800-0x8807, BIOS settings: hde:pio, hdf:pio <6> ide3: BM-DMA at 0x8808-0x880f, BIOS settings: hdg:pio, hdh:pio <7>Probing IDE interface ide2... <4>hde: SAMSUNG SP1213N, ATA DISK drive <4>hdf: SAMSUNG SP1614N, ATA DISK drive <4>ide2 at 0xa000-0xa007,0x9802 on irq 10 <7>ide_acpi_hwif_get_handle: ENTER: device ide2 <7>ide_get_dev_handle: ENTER: pci 00:11.0 <7>ide_get_dev_handle: for dev=0x11.0, addr=0x110000, parent=0xdff6ec00, *handle=0x00000000 <7>ide_acpi_hwif_get_handle: ide_get_dev_handle failed (-19) <7>ide_acpi_init: no ACPI object for ide2 found <6>hde: max request size: 128KiB <6>hde: 234493056 sectors (120060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) <6>hde: cache flushes supported <6> hde: hde1 hde2 < hde5 hde6 hde7 hde8 > hde3 hde4 <6>hdf: max request size: 128KiB <6>hdf: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) <6>hdf: cache flushes supported <6> hdf: hdf1 hdf2 A parallel installation of openSUSE 10.3 on the same machine treats the second ATA disk as PIO/4, see boot.msg excerpt below. If I trusted the messages, I would conclude openSUSE 10.3 shows a regression here. Any similar effects, any help? <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <7>pata_via 0000:00:04.1: version 0.3.1 <6>scsi0 : pata_via <6>scsi1 : pata_via <6>ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001d800 irq 14 <6>ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001d808 irq 15 <6>ata1.00: ATAPI: _NEC DV-5700B, 1.91, max UDMA/33 <6>ata1.00: configured for UDMA/33 <5>scsi 0:0:0:0: CD-ROM _NEC DV-5700B 1.91 PQ: 0 ANSI: 5 <4>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 <7>PCI: setting IRQ 10 as level-triggered <6>ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 <6>scsi2 : pata_pdc202xx_old <6>scsi3 : pata_pdc202xx_old <6>ata3: PATA max UDMA/100 cmd 0x0001a000 ctl 0x00019802 bmdma 0x00018800 irq 10 <6>ata4: PATA max UDMA/100 cmd 0x00019400 ctl 0x00019002 bmdma 0x00018808 irq 10 <6>ata3.00: ATA-7: SAMSUNG SP1213N, TL100-24, max UDMA/100 <6>ata3.00: 234493056 sectors, multi 16: LBA48 <6>ata3.01: ATA-7: SAMSUNG SP1614N, TM100-30, max UDMA/100 <6>ata3.01: 312581808 sectors, multi 16: LBA48 <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/100 <5>scsi 2:0:0:0: Direct-Access ATA SAMSUNG SP1213N TL10 PQ: 0 ANSI: 5 <5>scsi 2:0:1:0: Direct-Access ATA SAMSUNG SP1614N TM10 PQ: 0 ANSI: 5 <6>ACPI: CPU0 (power states: C1[C1] C2[C2]) <6>ACPI: Processor [CPU0] (supports 16 throttling states) <6>BIOS EDD facility v0.16 2004-Jun-25, 2 devices found <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>USB Universal Host Controller Interface driver v3.0 <4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 <7>PCI: setting IRQ 9 as level-triggered <6>ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 <6>uhci_hcd 0000:00:04.2: UHCI Host Controller <6>uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 <6>uhci_hcd 0000:00:04.2: irq 9, io base 0x0000d400 <6>usb usb1: new device found, idVendor=0000, idProduct=0000 <6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: UHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.22.16-0.1-default uhci_hcd <6>usb usb1: SerialNumber: 0000:00:04.2 <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 2 ports detected <6>ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 <6>uhci_hcd 0000:00:04.3: UHCI Host Controller <6>uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2 <6>uhci_hcd 0000:00:04.3: irq 9, io base 0x0000d000 <6>usb usb2: new device found, idVendor=0000, idProduct=0000 <6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: UHCI Host Controller <6>usb usb2: Manufacturer: Linux 2.6.22.16-0.1-default uhci_hcd <6>usb usb2: SerialNumber: 0000:00:04.3 <6>usb usb2: configuration #1 chosen from 1 choice <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 2 ports detected <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda: sda1 sda2 < sda5 sda6 sda7<6>usb 1-2: new full speed USB device using uhci_hcd and address 2 <4> sda8 > sda3 sda4 <5>sd 2:0:0:0: [sda] Attached SCSI disk <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdb: sdb1 sdb2 <5>sd 2:0:1:0: [sdb] Attached SCSI disk <6>usb 1-2: new device found, idVendor=050f, idProduct=0003 <6>usb 1-2: new device strings: Mfr=0, Product=0, SerialNumber=0 <6>usb 1-2: configuration #1 chosen from 1 choice <6>hub 1-2:1.0: USB hub found <6>hub 1-2:1.0: 4 ports detected <4>Marking TSC unstable due to: possible TSC halt in C2. <6>Time: acpi_pm clocksource has been installed. <6>usb 1-2.1: new low speed USB device using uhci_hcd and address 3 <6>usb 1-2.1: new device found, idVendor=046d, idProduct=c00e <6>usb 1-2.1: new device strings: Mfr=1, Product=2, SerialNumber=0 <6>usb 1-2.1: Product: USB-PS/2 Optical Mouse <6>usb 1-2.1: Manufacturer: Logitech <6>usb 1-2.1: configuration #1 chosen from 1 choice <6>usb 1-2.2: new low speed USB device using uhci_hcd and address 4 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x6 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:04:5b:20:00/00:00:00:00:00/f0 Emask 0x30 (host bus error) <6>ata3: soft resetting link <6>usb 1-2.2: new device found, idVendor=046a, idProduct=0001 <6>usb 1-2.2: new device strings: Mfr=0, Product=0, SerialNumber=0 <6>usb 1-2.2: configuration #1 chosen from 1 choice <6>usbcore: registered new interface driver hiddev <6>input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 <6>input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:04.2-2.1 <6>ata3.00: configured for UDMA/100 <6>input: HID 046a:0001 as /class/input/input2 <6>ata3.01: configured for UDMA/100 <6>ata3: EH complete <6>input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:04.2-2.2 <6>usbcore: registered new interface driver usbhid <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/100 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/100 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <4>ata3.01: limiting speed to UDMA/66:PIO4 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/66 <6>ata3: EH complete <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/66 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/66 <6>sd 2:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:1:0: [sdb] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 00 20 5e <6>sd 2:0:1:0: [sdb] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sdb, sector 8279 <3>Buffer I/O error on device sdb1, logical block 4108 <4>lost page write due to I/O error on sdb1 <3>Buffer I/O error on device sdb1, logical block 4109 <4>lost page write due to I/O error on sdb1 <3>Buffer I/O error on device sdb1, logical block 4110 <4>lost page write due to I/O error on sdb1 <3>Buffer I/O error on device sdb1, logical block 4111 <4>lost page write due to I/O error on sdb1 <6>ata3: EH complete <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>kjournald starting. Commit interval 5 seconds <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/66 <6>ata3: EH complete <4>ata3.01: limiting speed to UDMA/33:PIO4 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:3f:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:46:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>sd 2:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:1:0: [sdb] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 00 00 46 <6>sd 2:0:1:0: [sdb] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sdb, sector 63 <3>Buffer I/O error on device sdb1, logical block 0 <4>lost page write due to I/O error on sdb1 <6>ata3: EH complete <6>EXT3 FS on sdb1, internal journal <6>EXT3-fs: mounted filesystem with ordered data mode. <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x4 <3>ata3.01: cmd ca/00:08:57:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 4096 out <4> res 51/84:01:5e:20:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for UDMA/33 <6>sd 2:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:1:0: [sdb] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 00 20 5e <6>sd 2:0:1:0: [sdb] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sdb, sector 8279 <3>Buffer I/O error on device sdb1, logical block 1027 <4>lost page write due to I/O error on sdb1 <6>ata3: EH complete <4>ata3.01: limiting speed to PIO4 <3>ata3.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.01: BMDMA stat 0x6 <3>ata3.01: cmd ca/00:10:5f:20:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 8192 out <4> res 51/84:04:6b:20:00/00:00:00:00:00/f0 Emask 0x30 (host bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>scsi 0:0:0:0: Attached scsi generic sg0 type 5 <5>sd 2:0:0:0: Attached scsi generic sg1 type 0 <5>sd 2:0:1:0: Attached scsi generic sg2 type 0 <6>Linux agpgart interface v0.102 (c) Dave Jones <6>ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 <4>3c59x: Donald Becker and others. <6>0000:00:0d.0: 3Com PCI 3c905C Tornado at f881a000. <6>agpgart: Detected VIA Twister-K/KT133x/KM133 chipset <6>agpgart: AGP aperture is 32M @ 0xe6000000 <4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 <7>PCI: setting IRQ 5 as level-triggered <6>ACPI: PCI Interrupt 0000:00:04.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 <7>PCI: Setting latency timer of device 0000:00:04.5 to 64 <4>sr0: scsi3-mmc drive: 17x/40x cd/rw xa/form2 cdda tray <6>Uniform CD-ROM driver Revision: 3.20 <7>sr 0:0:0:0: Attached scsi CD-ROM sr0 <7>parport_pc: VIA 686A/8231 detected <7>parport_pc: probing current configuration <7>parport_pc: Current parallel port base: 0x378 <6>parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5 <6>parport_pc: VIA parallel port: io=0x378, irq=7 <6>input: Power Button (FF) as /class/input/input3 <6>ACPI: Power Button (FF) [PWRF] <6>input: Power Button (CM) as /class/input/input4 <6>ACPI: Power Button (CM) [PWRB] <4>i2c-adapter i2c-9191: sensors disabled - enable with force_addr=0xe200 <6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 <6>rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 <4>rtc_cmos: probe of 00:05 failed with error -16 <6>Adding 2369576k swap on /dev/sda4. Priority:-1 extents:1 across:2369576k <6>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/100 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <4>ata3.00: limiting speed to UDMA/66:PIO4 <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/66 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/66 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:43:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:43:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/66 <6>ata3.01: configured for PIO4 <6>sd 2:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 a3 cf 43 <6>sd 2:0:0:0: [sda] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sda, sector 10735427 <3>Buffer I/O error on device sda8, logical block 3944 <4>lost page write due to I/O error on sda8 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/66 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <4>ata3.00: limiting speed to UDMA/33:PIO4 <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:44:cf:a3/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:4a:cf:a3/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>sd 2:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 a3 cf 4a <6>sd 2:0:0:0: [sda] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sda, sector 10735428 <3>Buffer I/O error on device sda8, logical block 3945 <4>lost page write due to I/O error on sda8 <3>Buffer I/O error on device sda8, logical block 3946 <4>lost page write due to I/O error on sda8 <3>Buffer I/O error on device sda8, logical block 3947 <4>lost page write due to I/O error on sda8 <3>Buffer I/O error on device sda8, logical block 3948 <4>lost page write due to I/O error on sda8 <3>Buffer I/O error on device sda8, logical block 3949 <4>lost page write due to I/O error on sda8 <3>Buffer I/O error on device sda8, logical block 3950 <4>lost page write due to I/O error on sda8 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:01:37:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 512 out <4> res 51/84:01:37:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for UDMA/33 <6>ata3.01: configured for PIO4 <6>sd 2:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK <6>sd 2:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor] <4>Descriptor sense data with sense descriptors (in hex): <6> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 <6> 00 23 5c 37 <6>sd 2:0:0:0: [sda] Add. Sense: Scsi parity error <4>end_request: I/O error, dev sda, sector 2317367 <4>printk: 1 messages suppressed. <3>Buffer I/O error on device sda6, logical block 3944 <4>lost page write due to I/O error on sda6 <6>ata3: EH complete <4>ata3.00: limiting speed to PIO4 <3>ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 <3>ata3.00: BMDMA stat 0x4 <3>ata3.00: cmd ca/00:07:38:5c:23/00:00:00:00:00/e0 tag 0 cdb 0x0 data 3584 out <4> res 51/84:01:3e:5c:23/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) <6>ata3: soft resetting link <6>ata3.00: configured for PIO4 <6>ata3.01: configured for PIO4 <6>ata3: EH complete <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sda] 234493056 512-byte hardware sectors (120060 MB) <5>sd 2:0:0:0: [sda] Write Protect is off <7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:1:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) <5>sd 2:0:1:0: [sdb] Write Protect is off <7>sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>loop: module loaded