Probleme mit RAID-Controller SLES9 und Primergy RX200
Hallo, hat jemand Erfahrung bei der Installation von SLES9 auf einem Fujitsu Siemens Primergy RX200 mit Hardware-Raid-Controller: Adaptec AIC-7902 Integrated Ultra320 SCSI Host Bus Adapter ? Trotz allem korrekten Einrichten des Raids (funktionierte mit dem vorher laufen Windoof problemlos) werden bei der Installation immer zwei Platten sda und sdb erkannt. Ohne Start per SP2-CD findet SLES9 gar keine Platten. Weiss da jemand wie man SLES9 auf dem Server inkl. Hardware-Raid installiert bekommt ? Danke schon mal für jede Antwort :-) -- Regards, Jens Strohschnitter ------------------------------------- *!!!LINUX LINUX LINUX LINUX LINUX!!!* * http://www.jens-strohschnitter.de * ------------------------------------- Set the controls for the heart of the sun -------------------------------------
Jens Strohschnitter wrote:
Hallo,
hat jemand Erfahrung bei der Installation von SLES9 auf einem Fujitsu Siemens Primergy RX200 mit Hardware-Raid-Controller:
Adaptec AIC-7902 Integrated Ultra320 SCSI Host Bus Adapter
Das ist doch kein Hardware-RAID-Controller, da brauchst du doch noch mindestens einen Zero-Channel RAID-Controller dazu. Und vermutlich gibt es für diese Kombination keinen Treiber für Linux. Hast du FSC mal direkt gefragt? Normalerweise sind die sehr bemüht um eine Antwort, auch wenn sie vielleicht negativ ausfällt. Sandy
Hallo,
hat jemand Erfahrung bei der Installation von SLES9 auf einem Fujitsu Siemens Primergy RX200 mit Hardware-Raid-Controller:
Adaptec AIC-7902 Integrated Ultra320 SCSI Host Bus Adapter
Das ist doch kein Hardware-RAID-Controller, da brauchst du doch noch mindestens einen Zero-Channel RAID-Controller dazu. Und vermutlich gibt es für diese Kombination keinen Treiber für Linux.
Hast du FSC mal direkt gefragt? Normalerweise sind die sehr bemüht um eine Antwort, auch wenn sie vielleicht negativ ausfällt.
Hi kein HW-Raidcontroller ? Also wir haben 9 dieser Server in unserer Citrixumgebung. Ich denke mal nicht dass wir da etwa ohne Hardware- raid arbeiten :-) Werde aber mal bei FSC nachfragen. Danke. -- Regards, Jens Strohschnitter ------------------------------------- *!!!LINUX LINUX LINUX LINUX LINUX!!!* * http://www.jens-strohschnitter.de * ------------------------------------- Set the controls for the heart of the sun -------------------------------------
Jens Strohschnitter wrote:
hat jemand Erfahrung bei der Installation von SLES9 auf einem Fujitsu Siemens Primergy RX200 mit Hardware-Raid-Controller:
Adaptec AIC-7902 Integrated Ultra320 SCSI Host Bus Adapter
Das ist doch kein Hardware-RAID-Controller, da brauchst du doch noch mindestens einen Zero-Channel RAID-Controller dazu. Und vermutlich gibt es für diese Kombination keinen Treiber für Linux.
Hast du FSC mal direkt gefragt? Normalerweise sind die sehr bemüht um eine Antwort, auch wenn sie vielleicht negativ ausfällt.
kein HW-Raidcontroller ? Also wir haben 9 dieser Server in unserer Citrixumgebung. Ich denke mal nicht dass wir da etwa ohne Hardware- raid arbeiten :-) Werde aber mal bei FSC nachfragen. Danke.
Uh, ich habe jetzt doch mal auf der Adaptec-Seite nachgesehen, wo tatsächlich steht, dass der Chip angeblich RAID 0,1 in Hardware unterstützt. Ich habe bei uns ein paar Primergy TX150 stehen, wo der Controller nur mit einem Zero-Channel-Controller zu einem Hardware-RAID zu überreden ist. Welche Treiber hast du denn ausprobiert? Auch den auf der Homepage von Adaptec? http://www.adaptec.com/ibm/downloads/a320raid-3_00_042z5d-1_sles9i586_i586_r... Natürlich steht dann direkt dabei, dass es keinen offiziellen Support von Adaptec für diesen als Beta deklarierten Treiber gibt. Ich finde den Support von Adaptec für Linux Kernel 2.6 ohnehin ziemlich erbärmlich. Sandy
hat jemand Erfahrung bei der Installation von SLES9 auf einem Fujitsu Siemens Primergy RX200 mit Hardware-Raid-Controller:
Adaptec AIC-7902 Integrated Ultra320 SCSI Host Bus Adapter
Welche Treiber hast du denn ausprobiert? Auch den auf der Homepage von > http://www.adaptec.com/ibm/downloads/a320raid-3_00_042z5d-1_sles9i586_i586_r... Natürlich steht dann direkt dabei, dass es keinen offiziellen Support von
Hi den Treiber hatte ich noch nicht probiert, aber wenn bei der Installation bereits nur auf z.B. sda installiert wird, kann ich da den Treiber im nachhinein installieren und wird dann das HW-Raid aktiv ? Werden dann die Platten automatisch synchronisiert ? Ich dachte immer, das HW-Raid muss bei der Installation aktiv sein, damit die 2. Platte bereits beim Install synchronisiert wird. Aber wie kann ich dann den Treiber bei der Installation bereits einbinden ? -- Regards, Jens Strohschnitter ------------------------------------- *!!!LINUX LINUX LINUX LINUX LINUX!!!* * http://www.jens-strohschnitter.de * ------------------------------------- Set the controls for the heart of the sun -------------------------------------
Jens Strohschnitter wrote:
http://www.adaptec.com/ibm/downloads/a320raid-3_00_042z5d-1_sles9i586_i586_r... Natürlich steht dann direkt dabei, dass es keinen offiziellen Support von
den Treiber hatte ich noch nicht probiert, aber wenn bei der Installation bereits nur auf z.B. sda installiert wird, kann ich da den Treiber im nachhinein installieren und wird dann das HW-Raid aktiv ? Werden dann die Platten automatisch synchronisiert ?
Bei einem Software-RAID bzw. einen in Software realisiertem RAID habe ich das tatsächlich so machen können. Bei echten Hardware-RAIDs ist das IMHO jedoch nicht möglich, da dann das RAID erst einmal formatiert wird und dabei alle vorhandenen Daten vernichtet werden. Im besten Fall beherrscht der Controller die Möglichkeit der RAID-Level-Migration und kann von JBOD nach RAID1 ohne Datenverlust migrieren. Ich glaube aber nicht, dass dieser Controller das kann.
Ich dachte immer, das HW-Raid muss bei der Installation aktiv sein, damit die 2. Platte bereits beim Install synchronisiert wird. Aber wie kann ich dann den Treiber bei der Installation bereits einbinden ?
Ich nehme an, dass du das gesamte System auf das RAID installieren willst? In dem Fall hast du nur zwei Möglichkeiten: a) Quäle Adaptec, dass die dir eine entsprechende Moduldiskette basteln oder bastle sie dir selbst aus dem Treiber des RPMs. b) Installiere das Grundsystem auf eine normale IDE-Platte, installiere dann den Treiber, hänge das RAID ein, kopiere alle Dateien auf das RAID, binde den RAID-Treiber in die initrd ein, passe die Pfade in /etc/fstab an und bete beim Neustart. (^-^) Sandy
Bei einem Software-RAID bzw. einen in Software realisiertem RAID habe ich das tatsächlich so machen können. Bei echten Hardware-RAIDs ist das IMHO jedoch nicht möglich, da dann das RAID erst einmal formatiert wird und dabei alle vorhandenen Daten vernichtet werden. Im besten Fall beherrscht der Controller die Möglichkeit der RAID-Level-Migration und kann von JBOD nach RAID1 ohne Datenverlust migrieren. Ich glaube aber nicht, dass dieser Controller das kann.
Ich dachte immer, das HW-Raid muss bei der Installation aktiv sein, damit die 2. Platte bereits beim Install synchronisiert wird. Aber wie kann ich dann den Treiber bei der Installation bereits einbinden ?
Ich nehme an, dass du das gesamte System auf das RAID installieren willst? In dem Fall hast du nur zwei Möglichkeiten: a) Quäle Adaptec, dass die dir eine entsprechende Moduldiskette basteln oder bastle sie dir selbst aus dem Treiber des RPMs. b) Installiere das Grundsystem auf eine normale IDE-Platte, installiere dann den Treiber, hänge das RAID ein, kopiere alle Dateien auf das RAID, binde den RAID-Treiber in die initrd ein, passe die Pfade in /etc/fstab an und bete beim Neustart. (^-^)
Hallo das klingt ja alles sehr Haarstreubend. Ich werde mal einen Call bei SBS aufmachen. Hoffe die können mir da eine "einfachere" Lösung anbieten :-) Aber auf alle Fälle vielen Dank für Deine Bemühungen. Werde eine evtl. Lösung natürlich an diesen Thread geben. -- Regards, Jens Strohschnitter ------------------------------------- *!!!LINUX LINUX LINUX LINUX LINUX!!!* * http://www.jens-strohschnitter.de * ------------------------------------- Set the controls for the heart of the sun -------------------------------------
Hallo
das klingt ja alles sehr Haarstreubend. Ich werde mal einen Call bei SBS aufmachen. Hoffe die können mir da eine "einfachere" Lösung anbieten :-) Aber auf alle Fälle vielen Dank für Deine Bemühungen. Werde eine evtl. Lösung natürlich an diesen Thread geben.
Lösung gefunden: Treiber-Diskette mit Raidsoftware von fsc-pc.de runterladen Diskettenimage erstellen Booten mit SLES9SP2 Beim Bootscreen F6 drücken pci=nommconf Bootoption setzen Installation starten --> Jetzt wird nach der Disk gefragt. --> Der Treiber wird eingebunden --> und siehe da - das System hat nur sda und das Raid klappt. -- Regards, Jens Strohschnitter ------------------------------------- *!!!LINUX LINUX LINUX LINUX LINUX!!!* * http://www.jens-strohschnitter.de * ------------------------------------- Set the controls for the heart of the sun -------------------------------------
participants (2)
-
Jens Strohschnitter
-
Sandy Drobic