Fritz-USB Ich renne gegen ne Wand.....
Das das Ding nur über Capi4Linux läuft war mir ja schon bekannt :-) Habe mir auch alles besorgt und wollte nun installieren Hier das Ergebniss: capiplugin: $Revision: 1.13 $ capiconn: 1.5 capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6)] linux:~ # capiinit start linux:~ # pppd call isdn/avm Plugin /etc/ppp/plugins/userpass.so loaded. Plugin /etc/ppp/plugins/capiplugin.so loaded. capiplugin: $Revision: 1.13 $ capiconn: 1.5 capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6)] linux:~ # capiinit show ERROR: no cards configured in /etc/capi.conf linux:~ # cat /proc/capi/controller linux:~ # pppd call isdn/avm Plugin /etc/ppp/plugins/userpass.so loaded. Plugin /etc/ppp/plugins/capiplugin.so loaded. capiplugin: $Revision: 1.13 $ capiconn: 1.5 capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6)] Klasse-verstehe hier nur noch Bahnhof-Zug weg :-( Glücklicherweise fand ich ne Install-log Datei * Installation log (Wed Oct 24 22:02:53 CEST 2001): Kernel: 2.4.4-4GB Card: fcusb Extracted from install_passive.txt: - Version : 03.09.10 - Build : 01.10.09 Libver: 2001.04.18 Sysver: 2001.03.08 Files: .: -rw-r--r-- 1 root root 149129 Oct 9 00:00 c4l-lib-2001.04.18-1.i386.rpm -rw-r--r-- 1 root root 44520 Oct 9 00:00 c4l-sys-2001.03.08-1.i386.rpm -rw-r--r-- 1 root root 715976 Oct 9 00:00 fcusb.o -rwx------ 1 root root 8431 Oct 9 00:00 install -rw-r--r-- 1 root root 81 Oct 9 00:00 install.card -rw-r--r-- 1 root root 237 Oct 24 22:02 install.log -rw-r--r-- 1 root root 56221 Oct 9 00:00 install_passive.de -rw-r--r-- 1 root root 51210 Oct 9 00:00 install_passive.en ./lib: -rw-r--r-- 1 root root 685406 Oct 9 00:00 fcusb-lib.o ./src.drv: ./src.sys: * usbmgr: version 0.4.6 * Host controller driver: usb-ohci * Host controller use count: 0 * Installing 'c4l_start' * /usr/share/doc/CAPI4Linux ok * CAPI tools ok * Starting USB device filesystem update... (Output of ls -laR /etc/usbmgr/vendor/057c) * Before update: ls: /etc/usbmgr/vendor/057c: No such file or directory * After adding entries for fcusb: /etc/usbmgr/vendor/057c: total 12 drwxr-xr-x 3 root root 4096 Oct 24 22:02 . drwxr-xr-x 62 root root 4096 Oct 24 22:02 .. drwxr-xr-x 2 root root 4096 Oct 24 22:02 0c00 /etc/usbmgr/vendor/057c/0c00: total 12 drwxr-xr-x 2 root root 4096 Oct 24 22:02 . drwxr-xr-x 3 root root 4096 Oct 24 22:02 .. -rw-r--r-- 1 root root 6 Oct 24 22:02 module * Content of installed file(s): File /etc/usbmgr/vendor/057c/0c00/module: fcusb * Running rpm * Copying driver, conf file and documentation * Running depmod: * Running insmod (for CAPI modules): Using /lib/modules/2.4.4-4GB/kernel/drivers/isdn/avmb1/capiutil.o Using /lib/modules/2.4.4-4GB/kernel/drivers/isdn/avmb1/kernelcapi.o Using /lib/modules/2.4.4-4GB/kernel/drivers/isdn/avmb1/capifs.o Using /lib/modules/2.4.4-4GB/kernel/drivers/isdn/avmb1/capi.o * Kernel log (for CAPI modules): Oct 24 22:03:13 linux kernel: CAPI-driver Rev 1.22 : loaded Oct 24 22:03:14 linux kernel: capifs: Rev 1.16 : loaded Oct 24 22:03:14 linux kernel: capi20: started up with major 68 Oct 24 22:03:14 linux kernel: kcapi: capi20 attached Oct 24 22:03:14 linux kernel: capi20: Rev1.49: started up with major 68 (middleware+capifs) * Leaving install script Scheint ja alles da zu sein........aber was habe ich da gefunden...ne Erromessage-datei-hier isse auch noch: /*--------------------------------------------------------------------------* \ CAPI 2.0 Messages \*--------------------------------------------------------------------------* / /*-- informative values (corresponding message was processed) -----*/ 0x0001 "NCPI not supported by current protocol, NCPI ignored"; 0x0002 "Flags not supported by current protocol, flags ignored"; 0x0003 "Alert already sent by another application"; /*-- error information concerning CAPI_REGISTER -----*/ 0x1001 "Too many applications" 0x1002 "Logical block size to small, must be at least 128 Bytes" 0x1003 "Buffer exceeds 64 kByte" 0x1004 "Message buffer size too small, must be at least 1024 Bytes" 0x1005 "Max. number of logical connections not supported" 0x1006 "Reserved" 0x1007 "The message could not be accepted because of an internal busy condition" 0x1008 "OS resource error (no memory ?)" 0x1009 "CAPI not installed" 0x100A "Controller does not support external equipment" 0x100B "Controller does only support external equipment" /*-- error information concerning message exchange functions -----*/ 0x1101 "Illegal application number" 0x1102 "Illegal command or subcommand or message length less than 12 bytes" 0x1103 "The message could not be accepted because of a queue full condition !! The error code does not imply that CAPI cannot receive messages directed to another controller, PLCI or NCCI" 0x1104 "Queue is empty" 0x1105 "Queue overflow, a message was lost !! This indicates a configuration error. The only recovery from this error is to perform a CAPI_RELEASE" 0x1106 "Unknown notification parameter" 0x1107 "The Message could not be accepted because of an internal busy condition" 0x1108 "OS Resource error (no memory ?)" 0x1109 "CAPI not installed" 0x110A "Controller does not support external equipment" 0x110B "Controller does only support external equipment" /*-- error information concerning resource / coding problems -----*/ 0x2001 "Message not supported in current state" 0x2002 "Illegal Controller / PLCI / NCCI" 0x2003 "Out of PLCI" 0x2004 "Out of NCCI" 0x2005 "Out of LISTEN" 0x2006 "Out of FAX resources (protocol T.30)" 0x2007 "Illegal message parameter coding" /*-- error information concerning requested services -----*/ 0x3001 "B1 protocol not supported" 0x3002 "B2 protocol not supported" 0x3003 "B3 protocol not supported" 0x3004 "B1 protocol parameter not supported" 0x3005 "B2 protocol parameter not supported" 0x3006 "B3 protocol parameter not supported" 0x3007 "B protocol combination not supported" 0x3008 "NCPI not supported" 0x3009 "CIP Value unknown" 0x300A "Flags not supported (reserved bits)" 0x300B "Facility not supported" 0x300C "Data length not supported by current protocol" 0x300D "Reset procedure not supported by current protocol" 0x300E "TEI assignment failed or supplementary service not supported" 0x3010 "Request not allowed in this state" /*-- informations about the clearing of a physical connection -----*/ 0x3301 "Protocol error layer 1 (broken line or B-channel removed by signalling protocol)" 0x3302 "Protocol error layer 2" 0x3303 "Protocol error layer 3" 0x3304 "Another application got that call" /*-- T.30 specific reasons -----*/ 0x3311 "Connecting not successful (remote station is no FAX G3 machine)" 0x3312 "Connecting not successful (training error)" 0x3313 "Disconnected before transfer (remote station does not support transfer mode, e.g. resolution)" 0x3314 "Disconnected during transfer (remote abort)" 0x3315 "Disconnected during transfer (remote procedure error, e.g. unsuccessful repetition of T.30 commands)" 0x3316 "Disconnected during transfer (local tx data underrun)" 0x3317 "Disconnected during transfer (local rx data overflow)" 0x3318 "Disconnected during transfer (local abort)" 0x3319 "Illegal parameter coding (e.g. SFF coding error)" /*-- disconnect causes from the network according to ETS 300 102-1/Q.931 -----*/ /*----- normal event -----*/ 0x3481 "Unallocated (unassigned) number" 0x3482 "No route to specified transit network" 0x3483 "No route to destination" 0x3486 "Channel unacceptable" 0x3487 "Call awarded and being delivered in an established channel" 0x3490 "Normal call clearing" 0x3491 "User busy" 0x3492 "No user responding" 0x3493 "No answer from user (user alerted)" 0x3495 "Call rejected" 0x3496 "Number changed" 0x349A "Non-selected user clearing" 0x349B "Destination out of order" 0x349C "Invalid number format" 0x349D "Facility rejected" 0x349E "Response to STATUS ENQUIRY" 0x349F "Normal, unspecified" /*----- resource unavailable -----*/ 0x34A2 "No circuit / channel available" 0x34A6 "Network out of order" 0x34A9 "Temporary failure" 0x34AA "Switching equipment congestion" 0x34AB "Access information discarded" 0x34AC "Requested circuit / channel not available" 0x34AF "Resources unavailable, unspecified" /*----- service or option not available -----*/ 0x34B1 "Quality of service unavailable" 0x34B2 "Requested facility not subscribed" 0x34B9 "Bearer capability not authorized" 0x34BA "Bearer capability not presently available" 0x34BF "Service or option not available, unspecified" /*----- service or option not implemented -----*/ 0x34C1 "Bearer capability not implemented" 0x34C2 "Channel type not implemented" 0x34C5 "Requested facility not implemented" 0x34C6 "Only restricted digital information bearer capability is available" 0x34CF "Service or option not implemented, unspecified" /*----- invalid message -----*/ 0x34D1 "Invalid call reference value" 0x34D2 "Identified channel does not exist" 0x34D3 "A suspended call exists, but this call identity does not" 0x34D4 "Call identity in use" 0x34D5 "No call suspended" 0x34D6 "Call having the requested call identity has been cleared" 0x34D7 "User not a member of closed user group" 0x34D8 "Incompatible destination" 0x34DB "Invalid transit network selection" 0x34DF "Invalid message, unspecified" /*----- protocol error -----*/ 0x34E0 "Mandatory information element is missing" 0x34E1 "Message type non-existent or not implemented" 0x34E2 "Message not compatible with call state or message type non-existent or not implemented" 0x34E3 "Information element non-existent or not implemented" 0x34E4 "Invalid information element contents" 0x34E5 "Message not compatible with call state" 0x34E6 "Recovery on timer expiry" 0x34EF "Protocol error, unspecified" /*----- interworking -----*/ 0x34FF "Interworking, unspecified" /*-- B3 protocol 7 (Modem) -----*/ 0x3500 "Normal end of connection"; 0x3501 "Carrier lost"; 0x3502 "Error on negotiation, i.e. no modem with error correction at other end"; 0x3503 "No answer to protocol request"; 0x3504 "Remote modem only works in synchronous mode"; 0x3505 "Framing fails"; 0x3506 "Protocol negotiation fails"; 0x3507 "Other modem sends wrong protocol request"; 0x3508 "Sync information (data or flags) missing"; 0x3509 "Normal end of connection from the other modem"; 0x350a "No answer from other modem"; 0x350b "Protocol error"; 0x350c "Error on compression"; 0x350d "No connect (timeout or wrong modulation)"; 0x350e "No protocol fall-back allowed"; 0x350f "No modem or fax at requested number"; 0x3510 "Handshake error"; /*-- error info concerning the requested supplementary service -----*/ 0x3600 "Supplementary service not subscribed"; 0x3603 "Supplementary service not available"; 0x3604 "Supplementary service not implemented"; 0x3606 "Invalid served user number"; 0x3607 "Invalid call state"; 0x3608 "Basic service not provided"; 0x3609 "Supplementary service not requested for an incoming call"; 0x360a "Supplementary service interaction not allowed"; 0x360b "Resource unavailable"; /*-- error info concerning the context of a supplementary service request -----*/ 0x3700 "Duplicate invocation"; 0x3701 "Unrecognized operation"; 0x3702 "Mistyped argument"; 0x3703 "Resource limitation"; 0x3704 "Initiator releasing"; 0x3705 "Unrecognized linked-ID"; 0x3706 "Linked response unexpected"; 0x3707 "Unexpected child operation"; Ich hoffe das es jemanden gibt,der weiß was da schief gelaufen ist........Ich weiss es nicht und hoffe sehr auf eure Hilfe :-) Es bedankt sich- Axel-Köln (SuSE7.2-Prof)
Das das Ding nur über Capi4Linux läuft war mir ja schon bekannt :-) Habe mir auch alles besorgt und wollte nun installieren Hier das Ergebniss:
capiplugin: $Revision: 1.13 $ capiconn: 1.5 capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6)] linux:~ # capiinit start linux:~ # pppd call isdn/avm Plugin /etc/ppp/plugins/userpass.so loaded. Plugin /etc/ppp/plugins/capiplugin.so loaded. capiplugin: $Revision: 1.13 $ capiconn: 1.5 capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6)] linux:~ # capiinit show ERROR: no cards configured in /etc/capi.conf
Hier sind die Einträge aus meiner /etc/capi.conf: card file proto io irq mem cardnr options # # USB drivers are supposed to be loaded by the USB manager (see comments in # /usr/share/doc/packages/usbmgr/*) in case of an hotplug event! Therefore this # file has been left empty causing "capiinit show" to fail. Use the CAPI file- # system instead: "cat /proc/capi/controller" fcusb2 fus2base.frm - - - - - Ich hoffe das hilft. Dirk
participants (2)
-
Axel Lindlau
-
DVornheder@t-online.de