Am Montag, 20. Dezember 2004 23:43 schrieb Ralf Kleemann:
Dirk Schneider schrieb:
Die Datei "/etc/sensors.conf" ist Dein Freund.
Dort die für die auf Deinem Motherboard verwendeten Sensor-Chipsätze relevante Sektion suchen und die Parameter für die Lüfter entsprechend einstellen. Ist dort alles beschrieben.
Wenn ich bei mir (Suse 9.1) sensors ausführe kommt als Rückmeldung "No sensors found!".
Ich habe ein ASUS K8V mit dem Chipsatz VIA K8T800 und VT8237. Ich habe in /etc/sensors.conf nach K8T800 und VT8237 gesucht aber nichts gefunden.
Kann es sein, daß das K8V von sensors nicht unterstützt wird?
Gruß Ralf
bei mir schaut das so aus: auszug aus sensors.conf ______________________ chip "as99127f-*" # Same as above for w83782d except that in5 and in6 negative voltages # are computed as in the w83781d. # Asus won't release a datasheet so this is guesswork. # Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak, # Victor G. Marimon and others for their feedback. # Dual power plane label in0 "VCore 1" label in1 "VCore 2" # Single power plane (A7V133, A7M266) # label in0 "VCore" # ignore in1 label in2 "+3.3V" label in3 "+5V" label in4 "+12V" # These last two may not make sense on all motherboards. label in5 "-12V" label in6 "-5V" compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) compute in4 ((28/10)+1)*@ , @/((28/10)+1) compute in5 -(240/60.4)*@ , -@/(240/60.4) compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4) # Depending on your motherboard, you have to choose between three formulae # for temp2. Quoting Artur Gawryszczak: # "I guess, that the formula "temp2 (@*30/43)+25, (@-25)*43/30" is correct # for those Asus motherboards, which get CPU temperature from internal # thermal diode (Pentium Coppermine, and above), and "temp2 @*2.0, @/2.0" # is correct for Athlon/Duron boards, which use a thermistor in the # socket." # The third formula was found and reported by Victor G. Marimon. # Asus CUV4X, Asus A7V8X # compute temp2 (@*30/43)+25, (@-25)*43/30 # Asus A7V133, Asus A7M266 compute temp2 @*2.0, @/2.0 # Asus CUSL2 # compute temp2 (@*60/43)+25,(@-25)*43/60 # See comments above if temp3 looks bad. What works for temp2 is likely # to work for temp3. compute temp3 @*2.0, @/2.0 # adjust this if your vid is wrong; see doc/vid # set vrm 9.0 # set limits to 5% for the critical voltages # set limits to 10% for the non-critical voltages # set limits to 20% for the battery voltage set in0_min vid*0.95 set in0_max vid*1.05 set in1_min vid*0.95 set in1_max vid*1.05 set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 set in3_min 5.0 * 0.95 set in3_max 5.0 * 1.05 set in4_min 12 * 0.90 set in4_max 12 * 1.10 set in5_max -12 * 0.90 set in5_min -12 * 1.10 set in6_max -5 * 0.95 set in6_min -5 * 1.05 # examples for temperature limits # set temp1_over 40 # set temp1_hyst 37 # set temp2_over 52 # set temp2_hyst 47 # set temp3_over 52 # set temp3_hyst 47 ------------------------------- weiß ja nich ob es dich weiter bringt... :( schlumpfine:/etc # sensors as99127f-i2c-0-2d Adapter: SMBus Via Pro adapter at e800 Algorithm: Non-I2C SMBus adapter VCore 1: +1.53 V (min = +1.28 V, max = +1.40 V) VCore 2: +1.53 V (min = +1.28 V, max = +1.40 V) +3.3V: +3.37 V (min = +3.13 V, max = +3.45 V) +5V: +4.97 V (min = +4.72 V, max = +5.24 V) +12V: +12.27 V (min = +10.79 V, max = +13.19 V) -12V: -12.83 V (min = -0.00 V, max = -0.00 V) -5V: -4.86 V (min = -0.00 V, max = -0.00 V) fan1: 2280 RPM (min = 1500 RPM, div = 4) fan2: 1776 RPM (min = 1500 RPM, div = 4) fan3: 1388 RPM (min = 1500 RPM, div = 4) temp1: +27°C (limit = +60°C) temp2: +38.4°C (limit = +120°C, hysteresis = +100°C) temp3: +14.0°C (limit = +120°C, hysteresis = +100°C) vid: +1.350 V alarms: beep_enable: Sound alarm enabled