Hallo,
vielleicht kann mir mal jemand einen Tip geben .....
Ich habe ein SuSE 8.2 System unter einem AMD Duron laufen.
Nun habe ich eine D-Link DWL-G520 Karte eingebaut, und den Atheros Treiber
(madwifi Projekt) heruntergeladen und entpackt.
Ein make lief durch, jedoch erscheinen nun beim laden via insmod Fehler
bzgl. der Kernelversion (als Beispiel):
[snip]
insmod -f ath_hal/ath_hal.
Warning: kernel-module version mismatch
ath_hal/ath_hal.o was compiled for kernel version 2.4.20-4GB
while this kernel is version 2.4.20-4GB-athlon
Warning: loading ath_hal/ath_hal.o will taint the kernel: non-GPL license -
Proprietary
See http://www.tux.org/lkml/#export-tainted for information about tainted
modules
Warning: loading ath_hal/ath_hal.o will taint the kernel: forced load
Module ath_hal loaded, with warnings
[/snip]
Ich mußte also händisch alle drei Module mittels der Option -f laden .....
In /var/log/messages erscheint nun folgendes:
[snip]
Sep 3 22:22:50 linux kernel: wlan: 0.7.1.1 BETA (Sam Leffler
)
Sep 3 22:23:07 linux kernel: ath_hal: 0.9.5.3 BETA (Sam Leffler
)
Sep 3 22:23:16 linux kernel: ath_pci: 0.8.3.2 BETA (Sam Leffler
)
Sep 3 22:23:16 linux kernel: PCI: Enabling device 00:09.0 (0014 -> 0016)
Sep 3 22:23:16 linux kernel: ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
Sep 3 22:23:16 linux kernel: ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54M
Sep 3 22:23:16 linux kernel: ath0: 802.11 address: 00:80:c8:1e:45:97
Sep 3 22:23:16 linux kernel: ath0: Atheros 5212: mem=0xe1800000, irq=9
Sep 3 22:23:24 linux /etc/hotplug/net.agent[2589]: No HW description found
... exiting
[/snip]
Es macht also den Eindruck, als wenn die Karte gefunden wurde, und
ansprechbar ist - ich habe noch keine Konfiguration durchgeführt.
Ein iwconfig gibt nun folgendes aus:
[snip]
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
sit0 no wireless extensions.
ath0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412GHz Access Point: 00:00:00:00:00:00
Bit Rate:0kb/s Tx-Power Off Sensitivity=0/3
Retry Off RTS thr Off Fragment thr Off
Encryption key Off
Power Management Off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[/snip]
Wie kann ich aber nn entweder die make Definitionen (Makefile.inc) insoweit
anpassen, daß die Fehler beim Laden nicht auftreten, oder aber, daß das
Laden der Module beim Booten des System (ggf. inkl. der -f Option)
durchgeführt wird?
Danke & Gruß
Torsten