Hallo, hab eine flash card als hd in meine firewall (motherboard Vie Epia CL6000) eingebaut und SuSe 9.1 neu installiert (minimal ohne X11) und upgedated. Es bootet (!) und läuft. Leistungshunger (noch ohne slimdrive dvd) während der Installation 25 - 35 Watt, Temp der CPU (lt Bios-Health) 55° Celsius ohne Lüfter. Für Interessierte gibts weiter unten ein paar Infos zur flashcard HD. Beim Booten passiert aber Merkwürdiges und ich wollt fragen, ob jemand einen Tipp geben kann. Beim booten gibts folgende Meldungen (aus boot.msg), die ich nicht ganz verstehe: -1. Was ist ide2 ? (nach ide0 = ok und ide1 = ok): <4>hda: SanDisk SDCFB-2048, CFA DISK drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <4>hdc: CRD-8240B, ATAPI CD/DVD-ROM drive <4>ide1 at 0x170-0x177,0x376 on irq 15 <3>ide2: I/O resource 0x3EE-0x3EE not free. <3>ide2: ports already in use, skipping probe ############################# -2. dma ist AUS-geschaltet ? Das ist aus boot.msg: <4>hda: max request size: 128KiB <6>hda: 4001760 sectors (2048 MB) w/1KiB Cache, CHS=3970/16/63, DMA <6> hda:<4>hda: dma_timer_expiry: dma status == 0x21 <4>hda: DMA timeout error <4>hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest } [ snip ] <4>hda: max request size: 128KiB <6>hda: 4001760 sectors (2048 MB) w/1KiB Cache, CHS=3970/16/63, DMA <6> hda:<4>hda: dma_timer_expiry: dma status == 0x21 <4>hda: DMA timeout error <4>hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest } [ snip ] <6> hda: hda1 hda2 (Zeile 164 ..) <6> hda: hda1 hda2 <6> hda: hda1 hda2 ... <6> hda: hda1 hda2 <6> hda: hda1 hda2 <6> hda: hda1 hda2 (Zeile 257, ergo ca. fast 100 mal ????) [ snip ] Activating swap-devices in /etc/fstab... doneChecking root file system... fsck 1.34 (25-Jul-2003) ****************************************************** * Warning: The dma on your hard drive is turned off. * * This may really slow down the fsck process. * ****************************************************** Reiserfs super block in block 16 on 0x302 of format 3.6 with standard journal Blocks (total/free): 444400/313348 by 4096 bytes Filesystem is clean Filesystem seems mounted read-only. Skipping journal replay. ########################################## => dma turned off == das sagt auch yast->IDE DMA-Modus: Akt DMA-Modus: aus Geräte-Name: SDCFB-2048 Typ: Festplatte Gerät: /def/hda Benötigter DMA-Modus: Keine Änderung => hmm, soll ich das anschalten? Immerhin ergibt hdparm -I /dev/hda: # hdparm -I /dev/hda /dev/hda: CompactFlash ATA device, with removable media Model Number: SanDisk SDCFB-2048 Serial Number: 019307H2504N0548 Firmware Revision: HDX 2.18 Standards: Supported: 10 Likely used: 10 Configuration: Logical max current cylinders 3970 3970 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 4001760 LBA user addressable sectors: 4001760 device size with M = 1024*1024: 1953 MBytes device size with M = 1000*1000: 2048 MBytes (2 GB) Capabilities: LBA, IORDY(may be)(cannot be disabled) Queue depth: 1 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 1 Current = 1 DMA: mdma0 mdma1 *mdma2 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Jetzt noch eine Info zur Festplattengeschwindigkeit hdparm -t /dev/hda ergibt: /dev/hda: Timing buffered disk reads: 16 MB in 3.19 seconds = 5.02 MB/sec Meine normale Festplatte ist wohl ca 10mal schneller: Timing buffered disk reads: 166 MB in 3.01 seconds = 55.21 MB/sec Erst einmal Danke, Calli