Hallo, ohne sicher zu sein, das ich auch alle vorherigen Mails gesehen habe (Antworte doch immer auf die vorherigen Mails, auch eigene, damit der Zusammenhang erhalten bleibt!) Am Sonntag, 23. Januar 2005 23:28 schrieb Dieter Soost:
Hallo Alex,
ich poste jetzt mal auf Verdacht "ifconfig" und "route -n". Info: Die IP für eth1 habe ich auf "10.42.42.42 / 255.255.255.0" gesetzt.
ifconfig: ===================================================================== ======= dsl0 Link encap:Point-to-Point Protocol inet addr:192.168.99.1 P-t-P:192.168.99.99 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:4 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:0 (0.0 b) TX bytes:60 (60.0 b)
eth0 Link encap:Ethernet HWaddr 00:30:84:3E:F6:43 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::230:84ff:fe3e:f643/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72015 errors:0 dropped:0 overruns:0 frame:0 TX packets:80166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4447014 (4.2 Mb) TX bytes:86844458 (82.8 Mb) Interrupt:11 Base address:0xef00
eth1 Link encap:Ethernet HWaddr 00:E0:7D:F2:32:A7 inet addr:10.42.42.42 Bcast:10.42.42.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:7dff:fef2:32a7/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1176 errors:0 dropped:0 overruns:0 frame:0 TX packets:1034 errors:0 dropped:0 overruns:0 carrier:0 collisions:8 txqueuelen:1000 RX bytes:127441 (124.4 Kb) TX bytes:132015 (128.9 Kb) Interrupt:12 Base address:0x2e00
...
route -n ===================================================================== ======= Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.99.99 0.0.0.0 255.255.255.255 UH 0 0 0 dsl0 10.42.42.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.99.99 0.0.0.0 UG 0 0 0 dsl0 ===================================================================== =======
Du hast tatsächlich drei Netzwerkkarten? Eine zum anschluß direkt (via Crossover-kabel?) an das dsl-Modem und das hat die IP-Adresse 192.168.99.99 ?? eine für das Netzwek 192.168.0.X und eine für das Netzwerk 10.42.42.X Auf eth0 und eth1 ist wirklich traffic zu sehen dsl0 sieht ziemlich tot aus (das ist glaub ich dein Problem ?? ). Kannst Du das mal aufklären? Verwendest Du möglicherweise einen vlan-fähigen switch?
Danke !
Gruss Dieter
Viel Glück -- MfG Rolf Masfelder EMail: rolf.masfelder@nector.de