Hallo Liste, ich habe hier ein Problemchen mit Hylafax. Senden funktioniert, aber das Empfangen macht Probleme. Die TIFF's die erstellt werden sind nur 460 Byte gross. Hier ist mal ein Stück Log Datei, vielleicht könnt ihr damit was anfangen ? Ciao Björn recvq/fax00007.tif: Sender: 0049 375 7883862 Pages: 1 Quality: Fine Page: 1728 by 1 Received: 2001:09:10 18:34:47 TimeToRecv: 0:33 SignalRate: 14400 bit/s DataFormat: 2-D MR ---- Transcript of session follows ---- Sep 10 18:34:31.65: [ 276]: SESSION BEGIN 00000017 493757883862 Sep 10 18:34:31.65: [ 276]: <-- [4:ATA\r] Sep 10 18:34:34.12: [ 276]: --> [3:FAX] Sep 10 18:34:34.13: [ 276]: MODEM set baud rate: 19200 baud (flow control unchanged) Sep 10 18:34:34.13: [ 276]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF Sep 10 18:34:34.13: [ 276]: ANSWER: FAX CONNECTION Sep 10 18:34:34.13: [ 276]: MODEM input buffering enabled Sep 10 18:34:34.13: [ 276]: RECV FAX: begin Sep 10 18:34:40.57: [ 276]: --> [5:+FCON] Sep 10 18:34:41.61: [ 276]: --> [29:+FTSI: " 0049 XXX XXXXXXX"] Sep 10 18:34:41.62: [ 276]: REMOTE TSI "0049 XXX XXXXXXX" Sep 10 18:34:41.95: [ 276]: --> [22:+FDCS: 1,5,0,0,1,0,0,1] Sep 10 18:34:41.96: [ 276]: REMOTE wants 14400 bit/s Sep 10 18:34:41.96: [ 276]: REMOTE wants page width 1728 pixels in 215 mm Sep 10 18:34:41.96: [ 276]: REMOTE wants A4 page length (297 mm) Sep 10 18:34:41.96: [ 276]: REMOTE wants 7.7 line/mm Sep 10 18:34:41.96: [ 276]: REMOTE wants 2-D MR Sep 10 18:34:42.06: [ 276]: --> [2:OK] Sep 10 18:34:42.07: [ 276]: <-- [7:AT+FDR\r] Sep 10 18:34:45.06: [ 276]: --> [5:+FCFR] Sep 10 18:34:47.68: [ 276]: --> [22:+FDCS: 1,5,0,0,1,0,0,1] Sep 10 18:34:47.69: [ 276]: REMOTE wants 14400 bit/s Sep 10 18:34:47.69: [ 276]: REMOTE wants page width 1728 pixels in 215 mm Sep 10 18:34:47.69: [ 276]: REMOTE wants A4 page length (297 mm) Sep 10 18:34:47.69: [ 276]: REMOTE wants 7.7 line/mm Sep 10 18:34:47.69: [ 276]: REMOTE wants 2-D MR Sep 10 18:34:47.69: [ 276]: --> [7:CONNECT] Sep 10 18:34:47.69: [ 276]: RECV: begin page Sep 10 18:34:47.69: [ 276]: MODEM set XON/XOFF/FLUSH: input ignored, output generated Sep 10 18:34:47.69: [ 276]: RECV: send trigger 021 Sep 10 18:34:47.69: [ 276]: <-- data [1] Sep 10 18:35:15.92: [ 276]: RECV: 9 total lines, 0 bad lines, 0 consecutive bad lines Sep 10 18:35:15.92: [ 276]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled Sep 10 18:35:15.92: [ 276]: --> [17:+FPTS: 1,2219,0,0] Sep 10 18:35:25.34: [ 276]: --> [7:+FET: 2] Sep 10 18:35:25.35: [ 276]: RECV recv EOP (no more pages or documents) Sep 10 18:35:25.45: [ 276]: --> [2:OK] Sep 10 18:35:25.46: [ 276]: RECV send MCF (message confirmation) Sep 10 18:35:25.46: [ 276]: RECV FAX (00000017): from 0049 XXX XXXXXXX, page 1 in 0:43, A4, 7.7 line/mm, 2-D MR Sep 10 18:35:25.46: [ 276]: RECV FAX (00000017): recvq/fax00007.tif from 0049 XXX XXXXXXX, route to <unspecified>, 1 pages in 0:51 Sep 10 18:35:25.48: [ 276]: <-- [7:AT+FDR\r] Sep 10 18:35:28.50: [ 276]: --> [8:+FHNG: 0] Sep 10 18:35:28.50: [ 276]: REMOTE HANGU P: Normal and proper end of connection (code 0) Sep 10 18:35:28.50: [ 276]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "ttyS2" "00000017" ""