https://bugzilla.novell.com/show_bug.cgi?id=340978#c2
--- Comment #2 from Tambet Ingo 2007-11-13 01:34:01 MST ---
Here's the output:
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:0c:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:0c:00.0 to 64
ohci_hcd 0000:0c:00.0: OHCI Host Controller
ohci_hcd 0000:0c:00.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:0c:00.0: irq 16, io mem 0xb8000000
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.22.5-31-default ohci_hcd
usb usb5: SerialNumber: 0000:0c:00.0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
PCI: Enabling device 0000:0c:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:0c:00.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:0c:00.1 to 64
ohci_hcd 0000:0c:00.1: OHCI Host Controller
ohci_hcd 0000:0c:00.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:0c:00.1: irq 16, io mem 0xb8001000
usb usb6: new device found, idVendor=0000, idProduct=0000
usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.22.5-31-default ohci_hcd
usb usb6: SerialNumber: 0000:0c:00.1
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
usb 5-1: new full speed USB device using ohci_hcd and address 2
usb 5-1: new device found, idVendor=12d1, idProduct=1003
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: HUAWEI Mobile
usb 5-1: Manufacturer: HUAWEI Technologies
usb 5-1: configuration #1 chosen from 1 choice
option 5-1:1.0: GSM modem (1-port) converter detected
usb 5-1: GSM modem (1-port) converter now attached to ttyUSB0
The new ttyUSB0 device doesn't respond to 'AT' commands.
When things work (before 10.3) there are 3 serial ports for the card. ttyUSB0
for control and data, ttyUSB1 for signal strength monitoring, and ttyUSB2 (not
sure what it is or does).
--
Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug.