https://bugzilla.novell.com/show_bug.cgi?id=205509
------- Comment #5 from lavrinenko_alex@mail.ru 2006-09-21 02:41 MST -------
Szymon, I did normal installation. Here's my dmesg output:
Linux version 2.6.16.13-4-default (geeko@buildhost) (gcc version 4.1.0 (SUSE
Linux)) #1 Wed May 3 04:53:23 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001beb0000 (usable)
BIOS-e820: 000000001beb0000 - 000000001beb8000 (ACPI data)
BIOS-e820: 000000001beb8000 - 000000001bf00000 (ACPI NVS)
BIOS-e820: 000000001bf00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
446MB LOWMEM available.
found SMP MP-table at 000f64d0
On node 0 totalpages: 114352
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 110256 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 PTLTD ) @ 0x000f64a0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1beb3c1c
ACPI: FADT (v001 VN800 FIC_LM7R 0x06040000 PTL_ 0x000f4240) @ 0x1beb7eec
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x1beb7f60
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x1beb7fb0
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x1beb3d91
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x1beb3c54
ACPI: DSDT (v001 FIC LM7R 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: FIC Product ID: LM7R APIC at: 0xFEE00000
I/O APIC #1 Version 3 at 0xFEC00000.
Processors: 1
Allocating PCI resources starting at 30000000 (gap: 20000000:dffe0000)
Built 1 zonelists
Kernel command line: root=/dev/sda3 vga=791 resume=/dev/sda2 splash=silent
pci=noacpi noapic pci=usepirqmask irqpoll
bootsplash: silent mode.
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1396.770 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447784k/457408k available (1491k kernel code, 8968k reserved, 607k
data, 156k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2798.34 BogoMIPS (lpj=5596680)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Celeron(R) M processor 1.40GHz stepping 08
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 2314k freed
not found!
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8ec, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI Error (nsxfeval-0242): Handle is NULL and Pathname is relative [20060127]
ACPI Error (nsxfeval-0242): Handle is NULL and Pathname is relative [20060127]
ACPI Error (nsxfeval-0242): Handle is NULL and Pathname is relative [20060127]
ACPI Error (nsxfeval-0242): Handle is NULL and Pathname is relative [20060127]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
PCI: Found IRQ 5 for device 0000:00:06.0
PCI: Sharing IRQ 5 with 0000:00:0c.2
PCI: Sharing IRQ 5 with 0000:00:10.4
PCI: Sharing IRQ 5 with 0000:00:11.5
PCI: Sharing IRQ 5 with 0000:00:11.6
PCI: Found IRQ 10 for device 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:12.0
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
Setting up standard PCI resources
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:06: ioport range 0xfe10-0xfe11 has been reserved
pnp: 00:06: ioport range 0xfe00-0xfe00 has been reserved
PCI: Failed to allocate mem resource #6:10000@f4000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d1000000-d1ffffff
PREFETCH window: f0000000-f3ffffff
PCI: Bus 2, cardbus bridge: 0000:00:0c.0
IO window: 00002400-000024ff
IO window: 00002800-000028ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Found IRQ 10 for device 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:12.0
PCI: Setting latency timer of device 0000:00:0c.0 to 64
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1158840918.600:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
vesafb: framebuffer at 0xf0000000, mapped to 0xdc880000, using 6144k, total
65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:aa85
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 47089
bytes,<6>...found (1024x768, 27542 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
input: PC Speaker as /class/input/input3
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
LID MODM Z00A
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 156k freed
Write protecting the kernel read-only data: 281k
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
PCI: Found IRQ 9 for device 0000:00:0f.0
sata_via 0000:00:0f.0: routed to hard irq line 9
sata_via 0000:00:0f.0: enabling SATA channels (0x32)
ata1: SATA max UDMA/133 cmd 0x1430 ctl 0x1426 bmdma 0x1400 irq 9
ata2: SATA max UDMA/133 cmd 0x1428 ctl 0x1422 bmdma 0x1408 irq 9
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 00:045a 49:2f00 82:746b 83:7f01 84:6003 85:3c69 86:3f01 87:6003
88:40ff 93:0000
ata1: dev 0 ATA-7, max UDMA7, 78140160 sectors: LBA48
sata_get_dev_handle: SATA dev addr=0xf0000, handle=0x00000000
ata1: dev 0 configured for UDMA/133
sata_get_dev_handle: SATA dev addr=0xf0000, handle=0x00000000
scsi0 : sata_via
ata2: SATA link down (SStatus 0)
scsi1 : sata_via
Vendor: ATA Model: SAMSUNG HM040HI Rev: YA10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda:<6>input: PS/2 Mouse as /class/input/input4
input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Found IRQ 10 for device 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:12.0
PCI: Via IRQ fixup for 0000:00:0f.1, from 0 to 10
sd 0:0:0:0: Attached scsi generic sg0 type 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide1: BM-DMA at 0x1418-0x141f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide1...
hdc: PHILIPS CD-RW/DVD-ROM SCB5265, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (31 C)
ACPI: Fan [FAN] (on)
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 787176k swap on /dev/sda2. Priority:-1 extents:1 across:787176k
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper: module not supported by Novell, setting U taint flag.
ndiswrapper version 1.10 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5a (Broadcom,02/18/2005, 3.100.64.1) loaded
PCI: Enabling device 0000:00:06.0 (0000 -> 0002)
PCI: Found IRQ 5 for device 0000:00:06.0
PCI: Sharing IRQ 5 with 0000:00:0c.2
PCI: Sharing IRQ 5 with 0000:00:10.4
PCI: Sharing IRQ 5 with 0000:00:11.5
PCI: Sharing IRQ 5 with 0000:00:11.6
ndiswrapper: using irq 5
wlan0: vendor: ''
wlan0: ndiswrapper ethernet device 00:14:a5:44:4e:2a using driver bcmwl5a,
14E4:4318.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP
with WPA, WPA2, WPA2PSK
lp: driver loaded but no devices found
wlan0 renamed to eth1
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PCI: Found IRQ 5 for device 0000:00:10.4
PCI: Sharing IRQ 5 with 0000:00:06.0
PCI: Sharing IRQ 5 with 0000:00:0c.2
PCI: Sharing IRQ 5 with 0000:00:11.5
PCI: Sharing IRQ 5 with 0000:00:11.6
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 5, io mem 0xd0002800
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.13-4-default ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
PCI: Found IRQ 10 for device 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:12.0
Yenta: CardBus bridge found at 0000:00:0c.0 [1734:109b]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0c.0, mfunc 0x01ac1b22, devctl 0x64
Linux agpgart interface v0.101 (c) Dave Jones
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
Yenta: ISA IRQ mask 0x08d8, PCI irq 10
Socket status: 30000006
PCI: Found IRQ 10 for device 0000:00:12.0
PCI: Sharing IRQ 10 with 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:10.1
eth0: VIA Rhine II at 0x12000, 00:40:ca:d8:cc:12, IRQ 10.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 43e1.
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=5 option
and report if it works on your machine.
For more details, read ALSA-Configuration.txt.
PCI: Enabling device 0000:00:11.5 (0000 -> 0001)
PCI: Found IRQ 5 for device 0000:00:11.5
PCI: Sharing IRQ 5 with 0000:00:06.0
PCI: Sharing IRQ 5 with 0000:00:0c.2
PCI: Sharing IRQ 5 with 0000:00:10.4
PCI: Sharing IRQ 5 with 0000:00:11.6
PCI: Via IRQ fixup for 0000:00:11.5, from 255 to 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
USB Universal Host Controller Interface driver v2.3
eth1 renamed to wlan0
ieee1394: Initialized config rom entry `ip1394'
agpgart: Detected VIA P4M800CE chipset
agpgart: AGP aperture is 256M @ 0xe0000000
PCI: Enabling device 0000:00:0c.2 (0010 -> 0012)
PCI: setting IRQ 11 as level-triggered
PCI: Assigned IRQ 11 for device 0000:00:0c.2
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:00:10.4
PCI: Sharing IRQ 11 with 0000:00:11.5
PCI: Sharing IRQ 11 with 0000:00:11.6
PCI: Setting latency timer of device 0000:00:0c.2 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[d0002000-d00027ff]
Max Packet=[2048] IR/IT contexts=[4/8]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
PCI: Found IRQ 10 for device 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:12.0
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 10, io base 0x00001440
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.13-4-default uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:10.1
PCI: Sharing IRQ 10 with 0000:00:0c.0
PCI: Sharing IRQ 10 with 0000:00:0f.1
PCI: Sharing IRQ 10 with 0000:00:10.0
PCI: Sharing IRQ 10 with 0000:00:12.0
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 10, io base 0x00001460
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.13-4-default uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
usb 2-1: new device found, idVendor=046d, idProduct=c00e
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: configuration #1 chosen from 1 choice
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
dm-netlink version 0.0.2 loaded
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input6
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0040ca01347102dd]
loop: loaded (max 8 devices)
PCI: Enabling device 0000:00:11.6 (0000 -> 0001)
PCI: Found IRQ 11 for device 0000:00:11.6
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:00:0c.2
PCI: Sharing IRQ 11 with 0000:00:10.4
PCI: Sharing IRQ 11 with 0000:00:11.5
PCI: Via IRQ fixup for 0000:00:11.6, from 255 to 11
PCI: Setting latency timer of device 0000:00:11.6 to 64
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
IA-32 Microcode Update Driver: v1.14