https://bugzilla.novell.com/show_bug.cgi?id=270233 Summary: Module ata_piix has an almost unusably long start time Product: openSUSE 10.3 Version: Alpha 3 Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: Kernel AssignedTo: kernel-maintainers@forge.provo.novell.com ReportedBy: volker3204@paradise.net.nz QAContact: qa@suse.de PIII-450 Intel 440BX chipset 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) Booting the installation or rescue system takes approximately: basic drivers: 25s ata_piix: 1:45min (!!) usb devices: 35s ieee1394: 15s Booting 10.2 is much faster, and suppressing ata_piix thus using piix instead is much faster too, but gives the old hdX again. Boot dmesg contains <7>libata version 2.20 loaded. <7>ata_piix 0000:00:07.1: version 2.10ac1 <6>ata1: PATA max UDMA/33 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14 <6>ata2: PATA max UDMA/33 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15 <6>scsi0 : ata_piix <6>Time: acpi_pm clocksource has been installed. <6>ata1.00: ATA-7: SAMSUNG SP0802N, TK200-04, max UDMA/100 <6>ata1.00: 156368016 sectors, multi 16: LBA48 <6>ata1.01: ATAPI, max UDMA/100 <6>ata1.00: configured for UDMA/33 <6>ata1.01: configured for UDMA/33 <6>scsi1 : ata_piix <4>ATA: abnormal status 0x7F on port 0x00010177 <4>ATA: abnormal status 0x7F on port 0x00010177 <6>ata2.01: ATAPI, max UDMA/33 <4>ata2.01: qc timeout (cmd 0xef) <3>ata2.01: failed to set xfermode (err_mask=0x4) <4>ata2: failed to recover some devices, retrying in 5 secs <4>ATA: abnormal status 0x7F on port 0x00010177 <4>ATA: abnormal status 0x7F on port 0x00010177 <4>ata2.01: qc timeout (cmd 0xef) <3>ata2.01: failed to set xfermode (err_mask=0x4) <4>ata2.01: limiting speed to UDMA/33:PIO3 <4>ata2: failed to recover some devices, retrying in 5 secs <4>ATA: abnormal status 0x7F on port 0x00010177 <4>ATA: abnormal status 0x7F on port 0x00010177 <4>ata2.01: qc timeout (cmd 0xef) <3>ata2.01: failed to set xfermode (err_mask=0x4) <4>ata2.01: disabled <5>scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK20 PQ: 0 ANSI: 5 <5>SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB) <5>sda: Write Protect is off <7>sda: Mode Sense: 00 3a 00 00 <5>SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB) <5>sda: Write Protect is off <7>sda: Mode Sense: 00 3a 00 00 <5>SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 > <5>sd 0:0:0:0: Attached scsi disk sda <5>sd 0:0:0:0: Attached scsi generic sg0 type 0 <5>scsi 0:0:1:0: CD-ROM ASUS DVD-ROM E616 2.0 PQ: 0 ANSI: 5 <5>scsi 0:0:1:0: Attached scsi generic sg1 type 5 <6>ACPI: Fan [FAN] (on) <6>md: raid1 personality registered for level 1 <6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found <6>md: raid0 personality registered for level 0 <4>sr0: scsi3-mmc drive: 6x/48x cd/rw xa/form2 cdda tray <6>Uniform CD-ROM driver Revision: 3.20 <7>sr 0:0:1:0: Attached scsi CD-ROM sr0 The harddisk and dvdrom are there, but the cdwriter is missing - that looks like it's significant. The cdwriter hardware works (w 10.2). Yast logs and last boot dmesg attached. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is.