October 2008 - openSUSE Bugs - openSUSE Mailing Lists

[Bug 333658] New: lots of "Out of SW-IOMMU space" log messages from SATA disks with XEN
by bugzilla_noreply＠novell.com 10 Mar '09

10 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=333658#c1 Summary: lots of "Out of SW-IOMMU space" log messages from SATA disks with XEN Product: openSUSE 10.3 Version: Final Platform: x86-64 OS/Version: openSUSE 10.3 Status: NEW Severity: Normal Priority: P5 - None Component: Xen AssignedTo: cgriffin(a)novell.com ReportedBy: tilman(a)imap.cc QAContact: qa(a)suse.de Found By: Customer Intel Pentium D940 on Intel DQ965GF board, two SATA hard disks fresh install of openSUSE 10.3 64 bit with all available updates ts@xenon:~> uname -a Linux xenon 2.6.22.9-0.4-xen #1 SMP 2007/10/05 21:32:04 UTC x86_64 x86_64 x86_64 GNU/Linux When booting with XEN, /var/log/messages shows many error messages like the following: Oct 13 13:27:36 xenon kernel: PCI-DMA: Out of SW-IOMMU space for 32768 bytes at device 0000:00:1f.2 Oct 13 13:27:36 xenon kernel: ata2.00: exception Emask 0x0 SAct 0x10 SErr 0x0 action 0x0 Oct 13 13:27:36 xenon kernel: ata2.00: cmd 60/f8:20:87:3c:d6/02:00:02:00:00/40 tag 4 cdb 0x0 data 389120 in Oct 13 13:27:36 xenon kernel: res 40/00:08:e7:30:d6/00:00:02:00:00/40 Emask 0x40 (internal error) followed by what looks like a reset of the affected disk: Oct 13 13:27:36 xenon kernel: ata2.00: configured for UDMA/133 Oct 13 13:27:36 xenon kernel: ata2: EH complete Oct 13 13:27:36 xenon kernel: sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) Oct 13 13:27:36 xenon kernel: sd 1:0:0:0: [sdb] Write Protect is off Oct 13 13:27:36 xenon kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Oct 13 13:27:36 xenon kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA The frequency of these messages is about 10 per minute after boot but seems to ebb down later. The affected hard disk is mostly sdb (ata2) which hosts the root partition, but occasionally also sda (ata1) where /boot and /home reside. When booting without XEN, no such messages appear. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 9

[Bug 394351] New: Beta3P boot crashes at mmc0 init with card mounted
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=394351 Summary: Beta3P boot crashes at mmc0 init with card mounted Product: openSUSE 11.0 Version: Beta 3plus Platform: Other OS/Version: openSUSE 11.0 Status: NEW Severity: Normal Priority: P5 - None Component: Booting AssignedTo: jsrain(a)novell.com ReportedBy: stefan.l.arndt(a)gmx.net QAContact: jsrain(a)novell.com Found By: --- On my machine (ACER 8920) boot does not work with a mmc card mounted. The Card itself is readable with MS Vista. It stops with the following lines: ACPCI: PCI Interrupt 00000 ????? -> GSI->16 IRQ 16 mmc0: SDHCI at 0xfc0000 irq16 DMA ACPI: Sleep button (CM)(SLPD) mmc0: Got command interrupt 0x00040000 even ????? input: LIDSWITCH ?????? mmc0: error -22 whilst initiaqlizing SDIO card ACPCI: PCI Interrupt 00000 ????? -> GSI->16 IRQ 16 The above line is the last one. Removing the card fixes the problem. Question marks reflect that I do not know what was here. Regards Stefan Arndt -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 154

[Bug 338003] New: Tracker bug for GtkFileChooser issues
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=338003 Summary: Tracker bug for GtkFileChooser issues Product: openSUSE 10.3 Version: Final Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: GNOME - Platform AssignedTo: federico(a)novell.com ReportedBy: federico(a)novell.com QAContact: qa(a)suse.de Depends on: 169809,171077,201309,228318 Found By: Development We'll use this bug to track issues in GtkFileChooser. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 40

[Bug 437780] New: Nautilus doesn' t use Kerberos for authentication to Windows shares when user is logged in via Active Directory
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=437780 Summary: Nautilus doesn't use Kerberos for authentication to Windows shares when user is logged in via Active Directory Product: openSUSE 11.0 Version: Final Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: GNOME AssignedTo: bnc-team-gnome(a)forge.provo.novell.com ReportedBy: jhaygood(a)reaktix.com QAContact: qa(a)suse.de Found By: --- How to reproduce 1. Set up an openSUSE system to use Active Directory authentication using YaST 2. Log in to GNOME using your domain credentials 3. Verify that you have a Kerberos ticket by opening up Terminal and typing in "klist". 4. Browse the network. 5. Find a server on the same domain and connect to it. Expected Results: You should see all shares accessible to you, and be able to open and manipulate them without any password prompts Actual Results: You are prompted for a username/password/domain prompt. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 20

[Bug 264844] New: Ship with totem-gstreamer and totem-xine
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=264844 Summary: Ship with totem-gstreamer and totem-xine Product: openSUSE 10.2 Version: Final Platform: Other OS/Version: Other Status: NEW Severity: Enhancement Priority: P5 - None Component: GNOME AssignedTo: bnc-team-gnome(a)forge.provo.novell.com ReportedBy: martin(a)gamesplace.info QAContact: qa(a)suse.de Currently, OpenSuSE only ships with the gstreamer Totem. It would be nice if there would be two packages, one totem-gstreamer (installed by default) package and one totem-xine package. This would make it easier for users to use xine as a backend for Totem. A user could install totem-xine from the official repositories and would just have to install a working libxine version from 3d party repositories. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is.

1 4

[Bug 381139] New: [multiscreen]: Need to recheck configuration after coming back from suspend
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=381139 Summary: [multiscreen]: Need to recheck configuration after coming back from suspend Product: openSUSE 11.0 Version: Factory Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: GNOME AssignedTo: bnc-team-gnome(a)forge.provo.novell.com ReportedBy: captain.magnus(a)opensuse.org QAContact: qa(a)suse.de Found By: --- Before suspend; Was setup with a CRT 1024x768 to the left, Builtin 1450x1050 to the right During suspend; Unplugged CRT, plugged in LCD 1680x1050 After suspend; Out of sync on LCD as it tried to use screen resoultion/refresh from the CRT We need to recheck the monitor setup when coming back from a suspend as this would happen frequently when people move between office and home etc. Perhaps just disable xinerama if monitor have changed would do it for now. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 9

[Bug 392041] New: subversion reads from stdin even without tty and breaks
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=392041 Summary: subversion reads from stdin even without tty and breaks Product: openSUSE 11.0 Version: Beta 3 Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: Development AssignedTo: olh(a)novell.com ReportedBy: matz(a)novell.com QAContact: qa(a)suse.de Found By: --- This actually happens in cron scripts that work since years. The new subversion (subversion-1.5.0-83 for me) does this on repos with conflicts: % svn up < /dev/null U gcc/ChangeLog A gcc/testsuite/gcc.dg/torture/builtin-isinf_sign-1.c U gcc/testsuite/gfortran.dg/char_cast_1.f90 U gcc/testsuite/ChangeLog Conflict discovered in 'gcc/tree-ssa-alias.c'. Select: (p) postpone, (df) diff-full, (e) edit, (h) help for more options: svn: Can't read stdin: End of file found And then stops. I'm aware of --non-interactive. svn should be able to figure that out itself, namely when the input is not a tty. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 5

[Bug 383187] New: Broken RANDR 1.2 support in krandrtray
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=383187 Summary: Broken RANDR 1.2 support in krandrtray Product: openSUSE 11.0 Version: Beta 1 Platform: Other OS/Version: Other Status: NEW Severity: Normal Priority: P5 - None Component: KDE4 Applications AssignedTo: kde-maintainers(a)suse.de ReportedBy: sndirsch(a)novell.com QAContact: qa(a)suse.de Found By: --- With krandrtray of KDE4 always clone mode is applied, no matter what I configure. An Apply button is missing as well. A side-by-side configuration by using xrandr --output DVI-I_1/digital --right-of DVI-I_2/digital works fine. # xrandr Screen 0: minimum 320 x 200, current 1680 x 1050, maximum 3360 x 1050 DVI-I_1/analog disconnected DVI-I_1/digital connected 1680x1050+0+0 433mm x 271mm 1680x1050 59.9*+ 60.0 59.9 59.9* 1280x1024 59.9 1280x960 59.9 1024x768 60.0 800x600 60.3 56.2 640x480 60.0 DVI-I_2/analog disconnected DVI-I_2/digital connected 1680x1050+0+0 433mm x 271mm 1680x1050 59.9*+ 59.9 1280x1024 75.0 59.9 1280x960 59.9 1152x864 75.0 74.9 69.8 1024x768 75.1 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 75.0 72.8 66.7 60.0 720x400 70.1 I'll attach a screenshot of krandrtray. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 20

[Bug 426143] New: xen live migration timer problem
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=426143 Summary: xen live migration timer problem Product: openSUSE 11.0 Version: Final Platform: i386 OS/Version: openSUSE 11.0 Status: NEW Severity: Major Priority: P5 - None Component: Xen AssignedTo: cgriffin(a)novell.com ReportedBy: kristjan.eentsalu(a)err.ee QAContact: qa(a)suse.de Found By: --- Hello I have a problem with live migration, if I do a live migration from dom0 A which uptime is bigger than dom0 B, then timer hangs in domU uptimeA-uptimeB sec. dmesg shows this clocksource/0: Time went backwards: ret=2cfb262ddd2 delta=-9691479862 shadow=2cfaeb3b089 offset=3af5da5 printk: 253 messages suppressed. clocksource/0: Time went backwards: ret=2d0da2358af delta=-4729586777 shadow=2d0d8b9a6e3 offset=169e612 Found these in the internet: http://bugzilla.xensource.com/bugzilla/show_bug.cgi?id=1282 setting xen.independent_wallclock = 1 did not help and https://bugzilla.redhat.com/show_bug.cgi?id=426861#c41 but this seems to be resolved/fixed since xen 3.1.1 http://lists.xensource.com/archives/html/xen-devel/2008-08/msg00304.html running ntp in both dom0 and xen-3.2.1_16881_04-4.2 xen-libs-3.2.1_16881_04-4.2 kernel-xen-2.6.25.16-0.1 xen-tools-3.2.1_16881_04-4.2 Kristjan -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 22

[Bug 413219] New: Apache authn_dbd_module doesn't work with Postgresql
by bugzilla_noreply＠novell.com 09 Mar '09

09 Mar '09

https://bugzilla.novell.com/show_bug.cgi?id=413219 Summary: Apache authn_dbd_module doesn't work with Postgresql Product: openSUSE 11.1 Version: Factory Platform: x86-64 OS/Version: openSUSE 11.0 Status: NEW Severity: Normal Priority: P5 - None Component: Apache AssignedTo: bnc-team-apache(a)forge.provo.novell.com ReportedBy: mkaspar(a)it-media.cz QAContact: qa(a)suse.de Found By: --- I tried to configure Apache to authentize against PostgreSQL DB. I wanted to use authn_dbd_module but after configuration, Apache fails to start with error message: Syntax error on line 1 of /etc/apache2/conf.d/dbd.conf: DBD: Failed to load driver apr_dbd_pgsql_driver I'v got libapr-util1-dbd-pgsql-1.2.12-43.1 installed, dbd and authn_dbd modules loaded via sysconfig/apache2. I created /etc/apache2/conf.d/dbd.conf file with: DBDriver pgsql DBDParams "dbname=db user=user password=password" DBDMin 4 DBDKeep 8 DBDMax 20 DBDExptime 300 It's on openSUSE 11 with all the updates installed. The same problem appears on openSUSE 10.3. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

1 8