[opensuse-arm] no HDMI on openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz
The title says it all. No HDMI on this specific build. openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz Otherwise, it boots/runs. I'm going to flog it a bit more. -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
On Mon, 13 Oct 2014 01:19:16 -0700 lists <lists@lazygranch.com> wrote:
The title says it all. No HDMI on this specific build. openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz
Otherwise, it boots/runs. I'm going to flog it a bit more.
This image seems to have other problems. I used zypper update, then issued the reboot command. The display on the serial port got to "starting kernel" and just froze there. I did a reboot by hand (i.e. hold the boot button and apply power). --------------------------------------------- U-Boot 2013.04 (Mar 17 2014 - 15:34:07) I2C: ready DRAM: 512 MiB WARNING: Caches not enamusb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode contnot set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 mmc0 is current device SD/MMC found on device 0 1950 bytes read in 6 ms (317.4 KiB/s) Running bootscript from mmc0 ... ## Executing script at 80200000 kerneladdr=0x802000004504224 bytes read in 609 ms (7.1 MiB/s) ** File not found initrd ** 21959 bytes read in 24 ms (892.6 KiB/s) ## Flattened Device Tree Tree in pla885c6 Starting kernel ... ------------------------------ Again, nothing happens. To be sure, I went to the HDMI port, just to see if the display got transferred there, and again, nothing. At this point, I'm going to halt testing and wait until someone thinks there is an image with HDMI support. -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
Hi openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw second-boots fine, just checked. Could you show full log of the first boot? 14.10.2014 05:17, lists пишет:
On Mon, 13 Oct 2014 01:19:16 -0700 lists <lists@lazygranch.com> wrote:
The title says it all. No HDMI on this specific build. openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz
Otherwise, it boots/runs. I'm going to flog it a bit more.
This image seems to have other problems. I used zypper update, then issued the reboot command. The display on the serial port got to "starting kernel" and just froze there.
I did a reboot by hand (i.e. hold the boot button and apply power). --------------------------------------------- U-Boot 2013.04 (Mar 17 2014 - 15:34:07)
I2C: ready DRAM: 512 MiB WARNING: Caches not enamusb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode contnot set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 mmc0 is current device SD/MMC found on device 0 1950 bytes read in 6 ms (317.4 KiB/s) Running bootscript from mmc0 ... ## Executing script at 80200000 kerneladdr=0x802000004504224 bytes read in 609 ms (7.1 MiB/s) ** File not found initrd ** 21959 bytes read in 24 ms (892.6 KiB/s) ## Flattened Device Tree Tree in pla885c6
Starting kernel ...
------------------------------ Again, nothing happens. To be sure, I went to the HDMI port, just to see if the display got transferred there, and again, nothing.
At this point, I'm going to halt testing and wait until someone thinks there is an image with HDMI support.
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
participants (2)
-
lists -
Matwey V. Kornilov