Am 05.09.2017 um 12:11 schrieb Freek de Kruijf:
Op dinsdag 5 september 2017 08:53:02 CEST schreef Freek de Kruijf:
Op maandag 4 september 2017 14:28:24 CEST schreef u:
On 04.09.17 11:49, Freek de Kruijf wrote:
I used the latest JeOS image 2017.05.23-Build1.1 for the RPi1 (armv6l) on a SD card and booted the system, which went OK.
After that I did a "zypper dup --no-recommends" on that system which, at the end, shows the following message:
Output of grub2-arm-uboot-2.02-6.1.armv6hl.rpm %posttrans script: update-bootloader: 2017-09-04 11:31:09 <3> update-bootloader-1244
run_command.274: '/usr/lib/bootloader/grub2-efi/install' failed with exit code>
1, output: <<<<<<<<<<<<<<<< target = arm-efi ls: cannot access '/sys/firmware/efi/efivars': No such file or directory + /usr/sbin/grub2-install --target=arm-efi --no-nvram --removable Installing for arm-efi platform.
Can you try to run this command on its own? If it still fails, run it with strace -f and upload the output somewhere (or look at it and search for failures)?
Thanks!
Alex
The RPi1 is not EFI system, so I wonder why the target should be arm-efi.
# /usr/sbin/grub2-install --target=arm-efi --no-nvram --removable Installing for arm-efi platform. /usr/sbin/grub2-install: error: cannot find a GRUB drive for /dev/mmcblk0p2. Check your device.map.
# more /boot/grub2/device.map (hd0) /dev/disk/by-id/mmc-SDC_0x49910339
# ls /dev/disk/by-id/ mmc-SDC_0x49910339 mmc-SDC_0x49910339-part1 mmc-SDC_0x49910339-part2 mmc- SDC_0x49910339-part3
When running yast in ncurses to change the bootloader without any update I also get the same error message: Error Execution of command "[["/usr/bin/grub2-editenv", "list"]]" failed. Exit code: 1 Error output: /usr/bin/grub2-editenv: error: cannot find a GRUB drive for / dev/mmcblk0p2. Check your device.map.
I am able to continue and I get the default "GRUB for EFI", which I change for GRUB2 After that I get the message: Error Internal error. Please report a bug report with logs. Run save_y2logs to get complete logs. Details: unsuported architecture arm Caller: /usr/share/YaST2/lib/bootloader/stage1_proposal.rb:266:in `block in class:Stage1Proposal'
Obviously the architecture is armv6l.
Submitted bug#1057142: https://bugzilla.opensuse.org/show_bug.cgi?id=1057142
Got answer:
--- Comment #1 from Ladislav Slezák
--- Unfortunately RPi1 is not supported by YaST. YaST supports only aarch64 EFI based boards. On RPi1 you have configure booting manually. You can find some booting hints at https://en.opensuse.org/ HCL:Raspberry_Pi#Installing_the_openSUSE_Tumbleweed_image
I had started preparing arm for yast2-bootloader but I needed to wait until a yast2-core pull request got merged and packaged and I haven't followed up since. Basically we need to check all (Ruby?) code paths in there that check for aarch64 or arm64 and decide whether to extend those to arm as well - any volunteer? That is independent of the GRUB error. Regards, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org