Mailinglist Archive: opensuse (3106 mails)

< Previous Next >
Re: [opensuse] Wireless Card
  • From: Danesh Daroui <Danesh.D@xxxxxxxxxxxx>
  • Date: Thu, 15 Feb 2007 13:23:42 +0100
  • Message-id: <45D450CE.4000407@xxxxxxxxxxxx>
Kenneth Schneider wrote:
On Thu, 2007-02-15 at 11:59 +0100, Andreas Jaeger wrote:
Danesh Daroui <Danesh.D@xxxxxxxxxxxx> writes:

I ran hwinfo --wlan and the result is:

12: PCI 202.0: 0200 Ethernet controller [Created at pci.286]
UDI: /org/freedesktop/Hal/devices/pci_14e4_4320
Unique ID: rBUF._LuIAhxm4a3
Parent ID: qscc.S+4MMSCCLf5
SysFS ID: /devices/pci0000:00/0000:00:14.4/0000:02:02.0
SysFS BusID: 0000:02:02.0
Hardware Class: network
Model: "Hewlett-Packard Company nx9500 Built-in Wireless"
Vendor: pci 0x14e4 "Broadcom"
Device: pci 0x4320 "BCM4306 802.11b/g Wireless LAN Controller"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x12f4 "nx9500 Built-in Wireless"
Revision: 0x03
Driver: "bcm43xx"
Driver Modules: "bcm43xx"
Device File: eth0
Features: WLAN
Memory Range: 0xd0200000-0xd0201fff (rw,non-prefetchable)
IRQ: 201 (no events)
HW Address: 00:90:4b:53:b6:21
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412e-05 2.417e-05 2.422e-05 2.427e-05 2.432e-05
2.437e-05 2.442e-05 2.447e-05 2.452e-05 2.457e-05 2.462e-05 2.467e-05
2.472e-05 2.484e-05
WLAN bitrates: 1.2e-05 1.8e-05 2.4e-05 3.6e-05 4.8e-05 7.2e-05 9.6e-05
0.000108 2e-06 4e-06 1.1e-05 2.2e-05
WLAN encryption modes: WEP40 WEP104
WLAN authentication modes: open sharedkey
Module Alias: "pci:v000014E4d00004320sv0000103Csd000012F4bc02sc80i00"
Driver Info #0:
Driver Status: bcm43xx is active
Driver Activation Cmd: "modprobe bcm43xx"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #8 (PCI bridge)

I think it shows that my wireless card is installed successfully but I
can not still connect to a network...
Broadcom support is not quite fully working yet :-(

Andreas

It may not be fully working but the bcm43xx does, it is also in the
Linksys WPC54G which works quite well in my laptop. The OP needs to
extract the drivers from the windows .sys file and add them
to /lib/firmware.

I have .sys driver files for Windows. How can I use thin in OpenSuse without ndiswrapper?

--
To unsubscribe, e-mail: opensuse+unsubscribe@xxxxxxxxxxxx
For additional commands, e-mail: opensuse+help@xxxxxxxxxxxx

< Previous Next >
Follow Ups