Rajko M. wrote:
On Sunday 28 October 2007 12:51:54 pm Dennis J. Tuchler wrote:
The plea for help is a sort of double dip on this forum. I also posted a request for help with a driver for the Canon Pixma MP830. After sending that note, I tried to fix the problem myself by changing the parallel port connection provided in the SUSE-supplied driver with a USB port designation.
In short you connected printer using USB instead of parallel port cable.
The Canon PIXMA MP 830 connects to the computer by a USB port.
It wouldn 't accept it, saying that the port wasn't properly configured!
I would need more details on this, like this: Printer connected to computer and turned on. Started YaST > Hardware > Printer Do you see printer in YaST list, or there is no nothing? What message below list tells?
I downloaded a new driver from Gutenprint and then turned on Yast2 and went to Hardware>Printer. The printer was not spotted but I clicked "Edit" and found its driver in the collection of drivers. I loaded the driver. This time, there was no port designated, but I was told that the wrong spooler was chosen. SO, I guess the spooler picks the port. What now? (I hope this is all solved in 10.3 which I might be getting in a couple of months, depending on the status of my 10/3 order with SuSE)
It was already working, by the way, to connect the scanner feature to my computer. So, I tried to mount the usb port only to find I had no idea how to indicate the proper device in the mount command (I tried several of them, searched though the relevant man entries and even did a couple of apropos searches.)
You can mount hard drive connected to USB port, but not port itself.
If you can help me (despite my double-dipping), I would appreciate it.
It is obvious that there is no many with Canon Pixma MP830, but without more details people that know how to setup printers can't say what might be wrong, or help you to troubleshoot problem. For instance it would be helpful to turn printer on and run: dmesg | tail -n10
I ran dmesg | tail -n10 and got: usb 1-6.4: SerialNumber: 188C80 usb 1-6.4: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 6 usb-storage: waiting for device to settle before scanning Vendor: Canon Model: MP830Storage Rev: 0114 Type: Direct-Access ANSI SCSI revision: 02 sd 2:0:0:0: Attached scsi removable disk sda sd 2:0:0:0: Attached scsi generic sg0 type 0 usb-storage: device scan complete
to see what kernel is doing. Is registered any activity on USB port. Then command: hwinfo --printer I ran hwinfo --printer (as root) and saw:
21: USB 00.1: 10900 Printer [Created at usb.122] UDI: /org/freedesktop/Hal/devices/usb_device_4a9_1713_188C80_if1 Unique ID: vnL8.pR2kLXpvOP1 Parent ID: MtLc.sdOrso15kK4 SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.4/1-6.4:1.1 SysFS BusID: 1-6.4:1.1 Hardware Class: printer Model: "Canon MP830" Hotplug: USB Vendor: usb 0x04a9 "Canon" Device: usb 0x1713 "MP830" Revision: "1.14" Serial ID: "188C80" Speed: 480 Mbps Module Alias: "usb:v04A9p1713d0114dc00dsc00dp00ic07isc01ip02" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #14 (Hub) Thanks again for your help. -- Best regards, Dennis J. Tuchler University City, Missouri 63130 -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org