Here you go:
1) lsmod | grep hci_
uhci_hcd 32016 0 usbcore 112512 7 usblp,usb_storage,ndiswrapper,slusb,usbhid,uhci_hcd
2) cat /etc/fstab
/dev/hda1 / reiserfs acl,user_xattr 1 1 /dev/hda5 swap swap defaults 0 0 proc /proc proc defaults 0 0 sysfs /sys sysfs noauto 0 0 usbfs /proc/bus/usb usbfs noauto 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 /dev/cdrecorder /media/cdrecorder subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 0 0 /dev/fd0 /media/floppy subfs noauto,fs=floppyfss,procuid,nodev,nosuid,sync 0 0 none /subdomain subdomainfs noauto 0 0
3) fdisk -l /dev/... ['l' = lower case L; ... = usb drive, e.g. 'sda']
Disk /dev/sda: 300.0 GB, 300090728448 bytes 255 heads, 63 sectors/track, 36483 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 36482 293041633+ 83 Linux And just for kicks, the final installment of dmesg: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 8 if 0 alt 0 proto 2 vid 0x03F0 pid 0x8204 Vendor: Maxtor Model: OneTouch II Rev: 023g Type: Direct-Access ANSI SCSI revision: 04 SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: assuming drive cache: write through SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: assuming drive cache: write through sda: sda1 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0 usb-storage: device scan complete ReiserFS: sda1: found reiserfs format "3.6" with standard journal ReiserFS: sda1: using ordered data mode ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda1: checking transaction log (sda1) ReiserFS: sda1: Using r5 hash to sort names usb 1-2: USB disconnect, address 6 usb 1-2.4: USB disconnect, address 7 usb 1-2.7: USB disconnect, address 8 drivers/usb/class/usblp.c: usblp0: removed hub 1-0:1.0: over-current change on port 2 usb 1-2: new full speed USB device using uhci_hcd and address 9 hub 1-2:1.0: USB hub found hub 1-2:1.0: 7 ports detected usb 1-2.4: new full speed USB device using uhci_hcd and address 10 scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 10 usb-storage: waiting for device to settle before scanning usb 1-2.7: new full speed USB device using uhci_hcd and address 11 drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 11 if 0 alt 0 proto 2 vid 0x03F0 pid 0x8204 Vendor: Maxtor Model: OneTouch II Rev: 023g Type: Direct-Access ANSI SCSI revision: 04 SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: assuming drive cache: write through SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: assuming drive cache: write through sda: sda1 Attached scsi disk sda at scsi2, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0 usb-storage: device scan complete ReiserFS: sda1: found reiserfs format "3.6" with standard journal ReiserFS: sda1: using ordered data mode ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda1: checking transaction log (sda1) ReiserFS: sda1: Using r5 hash to sort names With best regards, Pete -- Peter N. Spotts | Science Correspondent The Christian Science Monitor One Norway Street, Boston, MA 02038 USA Office: 1-671-450-2449 | Office in home: 1-508-520-3139 www.csmonitor.com | www.peterspotts.net pspotts@alum.mit.edu