Any help please!!!!!!!!! SuSE 9.1 boots normally for the most part. I insert (or boot with) my d-link or Orinoco wireless card and get this. May 29 10:12:50 linux cardmgr[1611]: socket 0: Anonymous Memory May 29 10:12:50 linux cardmgr[1611]: executing: 'modprobe memory_cs 2>&1' May 29 10:12:50 linux cardmgr[1611]: + FATAL: Module memory_cs not found. May 29 10:12:50 linux cardmgr[1611]: modprobe exited with status 1 May 29 10:12:50 linux cardmgr[1611]: module /lib/modules/2.6.4-54.5-default/pcmcia/memory_cs.o not available May 29 10:12:50 linux cardmgr[1611]: bind 'memory_cs' to socket 0 failed: Invalid argument May 29 10:13:41 linux cardmgr[1611]: exiting No Network, so I excute as root: linux:~ # rcpcmcia restart Shutting down PCMCIA FATAL: Module ds is in use. FATAL: Module pcmcia_core is in use. failed Starting PCMCIA done linux:~ # Then I have network, and syslog says this: May 29 10:13:42 linux kernel: PCI: Found IRQ 10 for device 0000:00:0a.0 May 29 10:13:42 linux kernel: PCI: Sharing IRQ 10 with 0000:00:0d.0 May 29 10:13:42 linux kernel: Yenta: CardBus bridge found at 0000:00:0a.0 [1558:8501] May 29 10:13:42 linux kernel: Yenta: Using INTVAL to route CSC interrupts to PCI May 29 10:13:42 linux kernel: Yenta: Routing CardBus interrupts to PCI May 29 10:13:42 linux kernel: Yenta: ISA IRQ mask 0x08d8, PCI irq 10 May 29 10:13:42 linux kernel: Socket status: 30000010 May 29 10:13:42 linux kernel: PCI: Found IRQ 10 for device 0000:00:0a.1 May 29 10:13:42 linux kernel: Yenta: CardBus bridge found at 0000:00:0a.1 [1558:8501] May 29 10:13:42 linux kernel: Yenta: Using INTVAL to route CSC interrupts to PCI May 29 10:13:42 linux kernel: Yenta: Routing CardBus interrupts to PCI May 29 10:13:42 linux kernel: Yenta: ISA IRQ mask 0x08d8, PCI irq 10 May 29 10:13:42 linux kernel: Socket status: 30000006 May 29 10:13:43 linux cardmgr[3493]: watching 2 sockets May 29 10:13:43 linux kernel: cs: IO port probe 0x0c00-0x0cff: clean. May 29 10:13:43 linux kernel: cs: IO port probe 0x0820-0x08ff: clean. May 29 10:13:43 linux kernel: cs: IO port probe 0x0800-0x080f: clean. May 29 10:13:43 linux kernel: cs: IO port probe 0x03e0-0x04ff: excluding 0x4d0-0x4d7 May 29 10:13:43 linux kernel: cs: IO port probe 0x0100-0x03af: clean. May 29 10:13:43 linux kernel: cs: IO port probe 0x0a00-0x0aff: clean. May 29 10:13:43 linux cardmgr[3494]: socket 0: D-Link DWL-650 May 29 10:13:43 linux kernel: eth0: Station identity 001f:0009:0001:0004 May 29 10:13:43 linux kernel: eth0: Looks like an Intersil firmware version 1.4.9 May 29 10:13:43 linux kernel: eth0: Ad-hoc demo mode supported May 29 10:13:43 linux kernel: eth0: IEEE standard IBSS ad-hoc mode supported May 29 10:13:43 linux kernel: eth0: WEP supported, 104-bit key May 29 10:13:43 linux kernel: eth0: MAC address 00:40:36:A7:17:4C May 29 10:13:43 linux kernel: eth0: Station name "Prism I" May 29 10:13:43 linux kernel: eth0: ready May 29 10:13:43 linux kernel: eth0: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f May 29 10:13:45 linux kernel: eth0: Error -110 setting multicast list. May 29 10:13:45 linux last message repeated 2 times May 29 10:13:45 linux kernel: eth0: New link status: Connected (0001) May 29 10:13:55 linux kernel: eth0: no IPv6 routers present