Mailinglist Archive: opensuse-support (220 mails)

< Previous Next >
Re: [opensuse-support] Sata SSD physical sector size shown as 512bytes? And other stuff when moving root drive to new physical drive.
On Wed, Jan 30, 2019 at 10:58 PM Carlos E. R.
<robin.listas@xxxxxxxxxxxxxx> wrote:
And it boots? Then good :-)

Yes the system came back up fine, boots normally. The Suse logo
graphics stuff is not showing, only real text screen mode grub2
already to begin with, but that was already prior to the switch to
ssd.

There is a fstrim service or timer that should be on.

Okay thanks will see about those trim commands or procedures with SSD.

The current situation is: on every boot the system is detecting the
sata devices, shown in the kernel logs (journalctl -b) just fine, and
a bit later it shows some kind of exception and a reset of this one
sata device. the other sata disks (classical hdd) and cdrom dont show
this messages.
Also the same sata cable worked fine on the previous hdd type of
device, but I even replaced the old sata cable with a newer one for
the ssd now. But still.
This message shows up on every boot. when the device is initialised.
Is this something to worry about?
Thanks.

============================
Jan 29 19:21:33 linux010 kernel: ata3: SATA link up 3.0 Gbps (SStatus
123 SControl 300)
Jan 29 19:21:33 linux010 kernel: ata3.00: supports DRM functions and
may not be fully accessible
Jan 29 19:21:33 linux010 kernel: ata3.00: ATA-11: Samsung SSD 860 EVO
500GB, RVT02B6Q, max UDMA/133
Jan 29 19:21:33 linux010 kernel: ata3.00: 976773168 sectors, multi 1:
LBA48 NCQ (depth 31/32), AA
Jan 29 19:21:33 linux010 kernel: ata8.00: ATAPI: HL-DT-ST DVDRAM
GH22NS50, TN02, max UDMA/100
Jan 29 19:21:33 linux010 kernel: ata3.00: supports DRM functions and
may not be fully accessible
Jan 29 19:21:33 linux010 kernel: ata3.00: configured for UDMA/133
Jan 29 19:21:33 linux010 kernel: scsi 2:0:0:0: Direct-Access ATA
Samsung SSD 860 2B6Q PQ: 0 ANSI: 5
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: Attached scsi generic sg0 type 0
Jan 29 19:21:33 linux010 kernel: ata3.00: Enabling discard_zeroes_data


Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] 976773168 512-byte
logical blocks: (500 GB/466 GiB)
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] Write Protect is off
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Jan 29 19:21:33 linux010 kernel: ata3.00: Enabling discard_zeroes_data
Jan 29 19:21:33 linux010 kernel: sda: sda1 sda2 sda3
Jan 29 19:21:33 linux010 kernel: ata3.00: Enabling discard_zeroes_data
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] supports TCG Opal
Jan 29 19:21:33 linux010 kernel: sd 2:0:0:0: [sda] Attached SCSI disk

Jan 29 19:21:35 linux010 kernel: ata3.00: exception Emask 0x0 SAct
0xf00 SErr 0x0 action 0x6
Jan 29 19:21:35 linux010 kernel: ata3.00: irq_stat 0x40000008
Jan 29 19:21:35 linux010 kernel: ata3.00: failed command: READ FPDMA QUEUED
Jan 29 19:21:35 linux010 kernel: ata3.00: cmd
60/08:40:f8:40:40/00:00:01:00:00/40 tag 8 ncq dma 4096 in

res
41/84:08:f8:40:40/00:00:01:00:00/00 Emask 0x410 (ATA bus error) <F>
Jan 29 19:21:35 linux010 kernel: ata3.00: status: { DRDY ERR }
Jan 29 19:21:35 linux010 kernel: ata3.00: error: { ICRC ABRT }
Jan 29 19:21:35 linux010 kernel: ata3: hard resetting link

Jan 29 19:21:35 linux010 kernel: ata3: SATA link up 3.0 Gbps (SStatus
123 SControl 300)
Jan 29 19:21:35 linux010 kernel: ata3.00: supports DRM functions and
may not be fully accessible
Jan 29 19:21:35 linux010 kernel: ata3.00: supports DRM functions and
may not be fully accessible
Jan 29 19:21:35 linux010 kernel: ata3.00: configured for UDMA/133
Jan 29 19:21:35 linux010 kernel: ata3: EH complete
Jan 29 19:21:35 linux010 kernel: ata3.00: Enabling discard_zeroes_data
--
To unsubscribe, e-mail: opensuse-support+unsubscribe@xxxxxxxxxxxx
To contact the owner, e-mail: opensuse-support+owner@xxxxxxxxxxxx

< Previous Next >
Follow Ups
References