Am Sonntag, 15. August 2004 18:22 schrieb Christian Boltz:
Interessant, dass Du mir/uns das mitteilst ;-)
Die Lösung Deines Problems solltest Du auf folgender Seite finden: http://www.dets-home.de/it-writings/smart-questions-ger.html
Gruß
Christian Boltz
PS: Wenn Du eine sinnvolle Antwort willst, wären ein paar Angaben mehr recht hilfreich, u. a. - Ausschnitt aus /var/log/messages bei rcnetwork restart (und natürlich die Ausgabe von rcnetwork restart selbst) - Ausgabe von ifconfig - der Inhalt von /etc/sysconfig/network/ifcfg-eth* und ifcfg-wlan* im gleichen Verzeichnis (WLAN-Key usw. "maskieren") - Ausgabe von lsmod
Bei mir funktioniert das kabelgebundene Netzwerk auf einem TM 803 übrigens problemlos. WLAN habe ich noch kaum getestet - beim letzten Test war es etwas instabil, das ist aber ein paar Kernel-Updates her ;-)
Hallo Christian, hallo Leute! Danke das Ihr mir helfen wollt! Ich habe mal alle Ausgaben hergenommen und zeige sie euch nun: Quaggelmaschine:/home/andreas # rcnetwork start Hint: you may set mandatory devices in /etc/sysconfig/network/config Setting up network interfaces: lo lo warning: using NO encryption lo command 'iwconfig lo mode auto' returned Error for wireless request "Set Mode" (8B06) : SET failed on device lo ; Operation not supported. lo command 'iwconfig lo nick Quaggelmaschine' returned Error for wireless request "Set Nickname" (8B1C) : SET failed on device lo ; Operation not supported. lo command 'iwconfig lo rate auto' returned Error for wireless request "Set Bit Rate" (8B20) : SET failed on device lo ; Operation not supported. lo command 'iwconfig lo key off' returned Error for wireless request "Set Encode" (8B2A) : SET failed on device lo ; Operation not supported. lo command 'iwconfig lo essid any' returned Error for wireless request "Set ESSID" (8B1A) : SET failed on device lo ; Operation not supported. done eth0 device: Broadcom Corporation BCM4401 100Base-T (rev 01) eth0 configuration: eth-id-00:c0:9f:26:2c:aa eth0 warning: using NO encryption eth0 command 'iwconfig eth0 mode auto' returned Error for wireless request "Set Mode" (8B06) : SET failed on device eth0 ; Operation not supported. eth0 command 'iwconfig eth0 nick Quaggelmaschine' returned Error for wireless request "Set Nickname" (8B1C) : SET failed on device eth0 ; Operation not supported. eth0 command 'iwconfig eth0 rate auto' returned Error for wireless request "Set Bit Rate" (8B20) : SET failed on device eth0 ; Operation not supported. eth0 command 'iwconfig eth0 key off' returned Error for wireless request "Set Encode" (8B2A) : SET failed on device eth0 ; Operation not supported. eth0 command 'iwconfig eth0 essid any' returned Error for wireless request "Set ESSID" (8B1A) : SET failed on device eth0 ; Operation not supported. done eth1 device: Intel Corp. PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04) eth1 configuration: wlan-bus-pci-0000:02:04.0 eth1 warning: using NO encryption eth1 command 'iwconfig eth1 mode Managed' returned Error for wireless request "Set Mode" (8B06) : SET failed on device eth1 ; Input/output error. eth1 command 'iwconfig eth1 rate auto' returned Error for wireless request "Set Bit Rate" (8B20) : SET failed on device eth1 ; Operation not supported. SIOCSIFFLAGS: Success eth1 (DHCP) . . . . . no IP address yet... backgrounding. waitin dsl0 dsl0 Startmode is 'manual' skippe Setting up service network . . . . . . . . . . . . . . . . done Quaggelmaschine:/home/andreas # dmesg eth1: Using hotplug firmware load. eth1: Firmware not available or load failed eth1: ipw2100_get_firmware failed: -2 eth1: Failed to power on the adapter. eth1: Failed to start the firmware. eth1: Using hotplug firmware load. eth1: Firmware not available or load failed eth1: ipw2100_get_firmware failed: -2 eth1: Failed to power on the adapter. eth1: Failed to start the firmware. Quaggelmaschine:/home/andreas # ifconfig eth0 eth0 Protokoll:Ethernet Hardware Adresse 00:C0:9F:26:2C:AA BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:5 Quaggelmaschine:/home/andreas # ifconfig eth1 eth1 Protokoll:Ethernet Hardware Adresse 00:00:00:00:00:00 BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:10 Basisadresse:0xc000 Speicher:d0206000-d0206fff Quaggelmaschine:/etc/sysconfig/network # more ifcfg-eth-id-00\:c0\:9f\:26\:2c\:aa NETWORK='192.168.2.1' BOOTPROTO='dhcp' MTU='1492' REMOTE_IPADDR='' STARTMODE='onboot' UNIQUE='LHB6.uE+1Gsq0aS2' _nm_name='eth0-to-smc' Quaggelmaschine:/etc/sysconfig/network # more ifcfg-eth-id-00\:c0\:9f\:26\:2c\:aa NETWORK='192.168.2.1' BOOTPROTO='dhcp' MTU='1492' REMOTE_IPADDR='' STARTMODE='onboot' UNIQUE='LHB6.uE+1Gsq0aS2' _nm_name='eth0-to-smc' Quaggelmaschine:/etc/sysconfig/network # more ifcfg-wlan-bus-pci-0000\:02\:04.0 BOOTPROTO='dhcp' MTU='1492' REMOTE_IPADDR='' STARTMODE='onboot' UNIQUE='UVH2.zosBAd2HjH5' WIRELESS_AP='' WIRELESS_BITRATE='auto' WIRELESS_CHANNEL='' WIRELESS_ESSID='' WIRELESS_FREQUENCY='' WIRELESS_KEY='' WIRELESS_MODE='Managed' WIRELESS_NICK='' WIRELESS_NWID='' WIRELESS_POWER='yes' _nm_name='bus-pci-0000:02:04.0'