Uff. Ich hab's. Vielen Dank an Alle, die geholfen haben. Jetzt klappt Senden + Empfangen. Hier nun die Zusammenfassung (Auflösung des Problems) Auch wenn das faxsetup einem Glauben macht, man müsse ModemResetCmds: ATS23=3&E8128901&L99 setzen ist das völlig falsch! Der Parameter &L99 ist wie Karsten Keil schon schrieb "daneben", denn da geht es um die MSN Genauso ist das Register S23 völlig daneben. Der Tatsächliche Befehl mus lauten: ModemResetCmds: AT&E8128901 wobei 8128901 durch die Eigene MSN ersetzt sein muss. Hier nun eine beispielhafte und komplette config.modem (sollte auch für andere funzen, wenn die MSN 8128901 durch die eigene MSN ersetzt wird). ---- SNIP ----- # $Id: i4l_class1,v 1.0 2000/10/20 09:09:37 kkeil Exp $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Generic I4L Class 1 modem configuration for Siemens ISURF or # Sedlbauer speedfax+ ISDN cards # CountryCode: 49 AreaCode: 911 FAXNumber: "+49 911 8128901" LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: "etc/dialrules" ServerTracing: 527 SessionTracing: 527 RecvFileMode: 0644 LogFileMode: 0600 DeviceMode: 0660 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-r -b -s %s %l" LocalIdentifier: "TypoType Nuernberg" TagLineFont: etc/lutRS18.pcf TagLineFormat: "Von: %%l|%c| Seite %%p von %%t" MaxRecvPages: 25 # # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint #ModemRate: 19200 # rate for DCE-DTE communication #ModemFlowControl: xonxoff # XON/XOFF flow control assumed # #ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem #ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: AT&E8128901 # stuff to do when modem is reset #ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1SwitchingCmd: delay:9 # silence between HDLC recv and trans Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration --- SNIP ---- Nochmals, vielen Dank allen Helfern.