* Eberhard Moenkeberg
(--) NV: Found NVIDIA GeForce 7300 GS at 05@00:00:0 ... (II) NV(0): Probing for analog device on output A... (--) NV(0): ...found one (II) NV(0): Probing for analog device on output B... (--) NV(0): ...found one (II) NV(0): Probing for EDID on I2C bus A... (II) NV(0): I2C device "DDC:E-EDID segment register" registered at address 0x60. (II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0. (--) NV(0): DDC detected a DFP: (II) NV(0): Manufacturer: SAM Model: 467 Serial#: 1129132596 (II) NV(0): Year: 2009 Week: 1 (II) NV(0): EDID Version: 1.3 (II) NV(0): Digital Display Input (II) NV(0): Max Image Size [cm]: horiz.: 52 vert.: 32 (II) NV(0): Gamma: 2.20 (II) NV(0): DPMS capabilities: Off (II) NV(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 (II) NV(0): First detailed timing is preferred mode (II) NV(0): redX: 0.650 redY: 0.337 greenX: 0.296 greenY: 0.604 (II) NV(0): blueX: 0.147 blueY: 0.074 whiteX: 0.312 whiteY: 0.329 ... (II) NV(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0 (II) NV(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0 (II) NV(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 170 MHz (II) NV(0): Monitor name: SyncMaster
With these infos, you can build an appropriate mode line:
Section "Modes" Identifier "Modes[0]" Modeline "1920x1200" 154 1920 1968 2000 2080 1200 1203 1209 1235 EndSection
which is indeed already in the log:
(II) NV(0): Printing DDC gathered Modelines: (II) NV(0): Modeline "1920x1200"x0.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync -vsync (74.0 kHz)
and a monitor section:
Section "Monitor" DisplaySize 520 320 HorizSync 30-81 Identifier "Monitor[0]" ModelName "SyncMaster" VertRefresh 56-75 UseModes "Modes[0]" EndSection
ok, mod xorg.conf as: diff ./xorg.conf.new ./xorg.conf.new.1 68,70c68,70 < Driver "nv" < VendorName "Unknown Vendor" < BoardName "Unknown Board" ---
Driver "nvidia" VendorName "nVidia" BoardName "7300GS"
101a102,115
EndSection
Section "Modes" Identifier "Modes[0]" Modeline "1920x1200" 154 1920 1968 2000 2080 1200 1203 1209 1235 EndSection
Section "Monitor" DisplaySize 520 320 HorizSync 30-81 Identifier "Monitor[0]" ModelName "SyncMaster" VertRefresh 56-75 UseModes "Modes[0]"
Same result, but now get EE vnc module version mis-match to libvnc... I guess this means that xorg.X11 is later version? http://wahoo.no-ip.org/~pat/Xorg.0.log.1 For this test, vnc is not important. Commented out the load order and retried. Now get no error, *but* still no screen, blank with backlight hints. http://wahoo.no-ip.org/~pat/Xorg.0.log.2 Changed driver from "nvidia" back to "nv" Now: (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) Still *no* screen! Past experience shows that this error results from the proprietary nVidia driver removing several files: missing /usr/lib64/dri/gallium/libGL.so.1 missing /usr/lib64/dri/gallium/libGL.so.1.2 missing /usr/lib64/libGL.so.1.2 missing /usr/lib/libGL.so.1.2 from: Mesa Mesa-32bit xorg-x11-driver-video-nouveau-3d after replacing the missing files: I was wrong, still blank/black screen. reinstalling the proprietary nvidia driver. tks, -- Patrick Shanahan Plainfield, Indiana, USA HOG # US1244711 http://wahoo.no-ip.org Photo Album: http://wahoo.no-ip.org/gallery2 Registered Linux User #207535 @ http://counter.li.org -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-factory+help@opensuse.org